Loading...
HomeMy WebLinkAboutFile Documents.601 E Hyman Ave.0131.2018 (4).ACBKEH RadiantElectric Heat CeramiCircuit™ Ceiling Cove Mount Heaters High Efficiency Ceramic Infrared Panels Model 945 • 1000 Watts Model 1445 • 1500 Watts Model 645 • 825 Watts Model 632 • 585 Watts The Ultimate in Energy Efficient HeatingSilent • Reliable • Economical• • • • • • • • • • • • • • • • • • • • • • • www.electricheat.com 800.774.4450 Apartments & Condos• Assisted Living• Medical & Clean Room• Remodeling• Residential• Commercial• Industrial• Garage and Shop• The CeramiCircuit™ ceiling cove mount heater provides rapid response comfort in 5 - 7 min- utes from an overhead mounting location which assures even and full distribution of the infrared energy it creates. There are no concerns about lost floor space with this heater. This assures maxi- mum comfort at lowest operating expense. Intended for indoor use only. Both models are available in beige or white. Matching mounting brackets and trim panels included. www.electricheat.com CeramiCircuit™ Ceiling Cove Mount Heaters Model 1445 • 1500 Watts Model 945 • 1000 Watts Model 645 • 825 Watts Model 632• 585 Watts Model Dimensions Watts BTUs Ship Wt. 945-C 46”W x 10”H x 7.5”D 1000 3414 22 lbs. 240 volt/4.2 amps 208 volt/4.8 amps 120 volt/8.3 amps 277 volt/3.6 amps 1445-C 46”W x 15”H x 10”D 1500 5150 40 lbs. 240 volt/6.2 amps 208 volt/7.2 amps 120 volt/12.5 amps 277 volt/5.4 amps 645-C 46”W x 7”H x 5.5”D 825 2817 17 lbs. 240 volt/3.4 amps 208 volt/3.9 amps 120 volt/6.8 amps 277 volt/2.9 amps 632-C 33”W x 7”H x 5.5”D 585 1989 14 lbs. 240 volt/3.4 amps 208 volt/2.9 amps 120 volt/4.8 amps 277 volt/2.3 amps Minimum Ceiling Clearance Minimum Elevation To Bottom Of Heater Supplied Mounting Brackets Provide Proper 36° Angle For Correct Energy Distribution 6" 6' Do Not Mount On Low Density Materials Such As Pegboard Hi g h e s t E n e r g y O u t p u t Lower Energy Output The room and all objects in it are gently saturated with infrared energy, just as if they were left in the sun on a warm day. Because heat seeks cold, all objects absorb, re-radiate and reflect the heat in all directions, meaning that comfort comes from every direction. Placing the heater on the exterior wall creates a barrier against the loss of body heat to the cold window under the heater. Cold floors aren't an issue with a CeramiCircuit™ installation. Even comfort is the rule with just a 4˚ floor to ceiling temperature difference being typical, although each structure will vary in this regard. The floor is warmed just like every other object in the room. © 2003 CeramiCircuit™ is a Registered Trademark of Radiant Electric Heat 410 Engineering Specifications The contractor shall supply and install CeramiCircuit™ infrared cove mounted heating panels, manufactured by Radiant Electric Heat, Inc., of the wattage and voltage specified on the plan. The heater shall be designed to provide maximum radiant heating energy output. Heater elements are to be constructed of ceramic coated 18 gauge steel plates with an energizing circuit on the internal face of the heating element. Heater body shall be a 20 gauge galvanized steel construct with ventilation slots at perimeter and 20 gauge steel bezel with high temperature powder coating. Heater shall have a junction box of approximately 6.75 inches on the back side of the heater body. There shall be three 7/8” standard knockouts in the junction box to allow entry of power feed. Actual power connections to the element and heater grounding connection shall be at the left end of the heater. Heater elements shall have a wattage density of a minimum of 2.3 watts/square inch of emissive surface area. Contractor shall install manufacturer’s supplied powder coated mounting brackets (2) as specified on the plan, and finish with supplied panel end trim pieces (2). Ratings & Approvals Heaters shall be rated at 585 watts (Model 632), 825 watts (Model 645), 1000 watts (Model 945), or 1500 watts (Model 1445) in appropriate voltages of 120 volts, 208 volts, 240 volts, or 277 volts. Heaters shall be listed and approved by Underwriter’s Laboratories . • Infrared energy heats people, not space. Find comfort at lower air temps . • Low temperature operation. Typically less than 350° F on the element. • Allergy free and sinus friendly. No pipes, no ducts, no furnace, no chimneys, no mainte- nance, no visible glow when in operation. • Ten year warranty, pro-rated after 5 years.