Loading...
HomeMy WebLinkAboutFile Documents.555 E Durant Ave.0120.2017 (9).ARBKSpecifications Additional information can be found online at www.heatilator.com 51-1/8" [1299] 62" [1575] 15-5/8"[397] 42-1/2"[1080] 4"[102] 8-9/16"[217] 63"[1600] 8-9/16"[217] 1" [25]58" [1473] 17-1/8"[435] 18-5/8"[471] 41-3/4"[1060] 2-3/8"[60] 8-9/16"[217] 24-1/2"[622] 8-7/8"[225] 2-3/4"[70] 7-1/4"[184] 23-3/4"[603] GAS ACCESS ELECTRICAL ACCESS CENTERED ON APPLIANCE Ø 8" [203] Please consult the manufacturer’s installation manual for all details and requirements before making a final design layout decision. Crave6048 48" Direct Vent Gas Fireplace Crave CRAVE6048 MODEL FRONT WIDTH BACK WIDTH HEIGHT DEPTH GLASS SIZE CRAVE6048 Actual Framing Actual Framing Actual Framing Actual Framing 47-1/2 x 12-1/25860-1/4 58 60-1/4 41-3/4 42 17-1/8 18-1/4 TOP FRONTLEFT RIGHT BEFORE FRAMING, PLEASE NOTE: A minimum of 24" of vertical venting is required before attaching any elbow to the appliance. Crave CRAVE6048 25"[635] 24"[610] 13-1/8"[333]16-3/4"[425] 52-5/16" [1329] 51" [1295] 49-3/16" [1249] 5/8" [16] 27-5/16"[692] 5-7/8"[149] 48-3/4" [1238] 57-5/8" [1463] 12-5/8"[321] 21-3/8"[543]27-5/16"[694] 5-7/8"[149] 49-1/8" [1248] 57-1/2" [1461] 12-1/8"[308] 21-3/8"[543] 19-7/16"[494] CLEAN FACE TRIM FIREPLACE VIEWING AREA17-1/4"[438] 51-1/8" [1299] OVERLAP FIT METHOD (FOUR SQUARE, ILLUSION) FIREPLACE VIEWING AREA 15-3/4"[400] 51-1/8" [1299] INSIDE FIT METHOD (CLEAN FACE TRIM) FOUR SQUARE FRONT ILLUSION FRONT FRONT DIMENSIONS FINISHED OPENING DIMENSIONS Decorative Front Dimensions and Framing • Rectangular holes on bottom of access panel should be covered. • Approved for 0"-4" finishing material on inside fit method • If finishing materials are 0-1” thick, the outer trim ring should be adjusted out so that the trim ring overlaps the finishing material. This is intended to provide the cleanest look. • If finishing materials are 1-4” thick, install the trim ring all the way in. Finishing materials may not extend past the outside edge of the trim ring. • Rectangular holes on bottom of access panel must be exposed. • ONLY approved for 0"-1" finishing material on overlap fit method • Rectangular holes on bottom of access panel must be exposed. • ONLY approved for 0"-1" finishing material on overlap fit method Specifications GS/HTL/CRAVE6048_0717 PRODUCT LISTING CODES US ANSI Z21.88-2014 CAN CSA 2.33-2014 UL307B Additional information can be found online at www.heatilator.com Product information provided is not complete and is subject to change without notice. Product installation must adhere strictly to instructions accompanying product to avoid risk of fire and potential injury. Lakeville, MN Phone: (800) 927-6841 Web: www.heatilator.com APPLIANCE LOCATION WALL PENETRATION MANTEL LEG/WALL PROJECTIONS 100-3/8"[2550] 70-3/4"[1797]60-1/4[1530]** 60-1/4[1530]** 60-1/4 [1530]** 60-1/4 [1530]** 18-1/4"[464] 28-1/2"[724]1"[25] 1"[25] See clearancesin install manual Refer to Section 10 of install manual for hearth, mantel and wall projection information. If a HEAT-ZONE® or HEAT-DUCT will be installed,refer to Section 5.E of install manual for information. 2 HEAT-ZONES = Add 4" to ** dimension 1 HEAT-ZONE = Add 2" to ** dimension FRAMING DIMENSIONS CLEARANCES TO COMBUSTIBLES 42"[1067] 60-1/4"[1530] 10"[254] HEADER DEPTH** 18-1/4"[464] APPLIANCE MAY BE INSTALLED OFF OF FLOOR*** * Adjust framing dimensions for interior sheathing (such as sheetrock) ** Header depth not to exceed 3-1/2". *** If appliance is installed off the floor, maintain required clearances to combustibles Construct platform in accordance with local building codes. Note: All measurements in inches. MEASUREMENTS FROM TOP EDGE OF THE APPLIANCE OPENING 4 5 6 13-16 3 2 1 6 7 8 9 10 11 18 31 MAX. MIN. TO CEILING Measurement from top edge of opening to bottom of appliance = 24-1/2 IN. OVERLAP FIT MEASUREMENTS FROM TOP EDGE OF THE APPLIANCE OPENING 4 5 6 14-16 0-9 10 18 31 MIN. MAX. TO CEILING Measurement from top edge of openingto bottom of appliance = 24-1/2 IN. 7 11 INSIDE FITNote: All measurements in inches. MEASUREMENT FROMTOP EDGE OPENING 18 20 23 26 29 31 TO CEILING 9 12 631 Measurement from top edge opening to bottom of appliance = 24-1/2" MAX. Note: All measurements in inches. MANTEL PROJECTIONS - NON-COMBUSTIBLE MANTEL PROJECTIONS - COMBUSTIBLE 63" [1600] 10"12" 63" [1600] Do not pack with insulation orother material * Shows center of vent framinghole for top venting. Center of holeis 1" [25] above center of horizontalvent pipe. 3 ft. maximum 4-1/2" minimum FIREPLACE OPENING See Appliance dimension diagram in install manual - Dimension B Note: Clearance from opening to perpendicualar wall Top View FIREPLACE OPENING See Appliance dimension diagram in install manual - Dimension B Note: Clearance from opening to perpendicualar wall Top View 7" minimum UNLIMITED Combustible Non-CombustibleAcceptable on both sides of opening 48"[1219] 0" 1" [25] 1" [25] 31" [787]Top ofFireplaceOpening toCeiling 0" 55-1/2"[1410]Bottom ofFireplace toCeiling Crave CRAVE6048