The URL can be used to link to this page

Home My WebLink AboutFile Documents.395 Thunderbowl Ln.0255.2018 (26).ARBK4/4/12 ANSI/APSP/ICC-‐ 15 Standard Writing Committee Form 1 of 2 1. _________ gallons ___ 2. _________ gpm ___ 3. _________ gpm ___ 4. _________ gpm ___ 5a. _________ inches ___ 5b. _________ inches ___ 5c. _________ inches ___ 5d. _________ inches ___ 6a. ___________________ 6b. _________ sq. ft.___ 7. _________ inches ___ Table 1 8a. ________________ 8b. _________ gpm ___ ___ a. Pump model b. Pump flow (§5.3.2.1, 5.3.2.2: Applicable Curve A or C gpm flow listed in database) d. Minimum return branch pipe diameter (Calculate: Item 4. ______(gpm) ÷ Branch Pipes ______(quantity) = branch flow rate _______(gpm). Enter the smallest pipe size from Table 1 with a 8 fps flow capacity the same or more than the calculated return branch flow rate.) 6. §5.4.1: Filter type and size: a. Filter type: (Cartridge, DE, Sand) b. Minimum filter area (Calculate: item 4. _______(gpm) ÷ filter factor ________) Filter factors: Cartridge=0.375, Sand=15, Diatomaceous Earth=2 7. §5.4.2: Backwash valve: ____Yes, ____No? (When using a backwash valve, enter result of item 5c or 2 inches whichever is larger) 8. Pump selection: §5.3.2.1: Pools 17,000 gallons or less, select pump* from the database with a Curve-‐A gpm flow equal to item 2 or less. §5.3.2.2: Pools 17,001 gallons or more, select pump* from the database with a Curve-‐C gpm flow equal to item 2 or less. *Multi-‐ speed pumps must have one speed listed that satisfies this requirement. 3. §5.2.2: Auxiliary Pool Load: ____Yes, ____No? (Enter the highest “auxiliary pool load” to be powered by the swimming pool filtration pump. Do not add auxiliary pool load flow rates together, only the highest is used.) 4. Calculated maximum flow rate (Item 2 or item 3, whichever is larger.) 5. §5.5.1: Pipe sizing: a. Minimum suction pipe diameter (Enter the smallest pipe size from Table 1 with a 6 fps flow capacity the same or more than item 4.) b. Minimum suction branch pipe diameter (Calculate: Item 4. ______(gpm) ÷ Branch Pipes ______(quantity) = branch flow rate _______(gpm). Enter the smallest pipe size from Table 1 with a 6 fps flow capacity the same or more than the calculated suction branch flow rate.) c. Minimum return pipe diameter (Enter the smallest pipe size from Table 1 with a 8 fps flow capacity the same or more than item 4.) OWNER:CONTRACTOR PHONE: DATE: This information sheet was prepared by the APSP-‐15 Residential Swimming Pool and Spa Energy Efficiency Standard Writing Committee of the Association of Pool and Spa Professionals (APSP). It is not part of the American National Standard ANSI/APSP/ICC-‐15 2011 but is included for information only. Contractors should acquire and comply with the ANSI/APSP/ICC-‐15 2011 standard which can be purchased at www.apsp.org. 1. §5.2.1: Calculated pool volume a. Gallons: ___________ ; or b. Calculated Gallons: ________(surface area) X ________ (average depth) X 7.48 (gal/ft^3) = _________ 2. §5.2.1: Calculated maximum filtration flow rate (Pool volume ÷ 360 or 36gpm whichever is larger) ANSI/APSP/ICC 15 ENERGY EFFICIENCY COMPLIANCE INFORMATION FOR RESIDENTIAL SWIMMING POOLS PROJECT NAME: AND ADDRESS CONTRACTOR NAME AND ADDRESS: Pipe Size: 1.5" 2" 2.5" 3" 3.5" 4" 5" 6" Nominal GPM @ 6 fps 38 63 90 138 185 238 374 540 Nominal GPM @ 8 fps 51 84 119 184 247 317 499 720 Print Save As PDF Lot #7 Thunderbowl 395 Thunderbowl Lane Aspen, CO 81611 Aspen Extreme II, LLC Even Flow Pools 3157 W 26th Ave Denver, CO 80211 (303) 995-3591 4/18/2019 8,399 0 8,399 36 4 4 36 1.5 36 1 36 1.5 1.5 36 1 36 1.5 Cartridge 36 0.375 96.0 2.0 Pentair VS3050 36 06/18/2019 4/4/12 ANSI/APSP/ICC-‐ 15 Standard Writing Committee Form 2 of 2 Component Section Check 4.4.1.1 4.4.1.2 4.3.1.3 4.3.2 5.1.1 5.3.1 5.3.3 5.3.4 5.5.2 5.5.3 5.5.6 Pool systems Pool filter pump listed in database Pool filter pump with total horsepower 1.0 or more is multi-‐speed Multi-‐speed pump controller programmed to default to the filtration flow rate when no auxiliary pool loads are operating within 24 hours and programmed with temporary override capability for servicing. Single-‐speed pump controller capable of operating pump during off-‐peak electric demand. Pipe before pump has at least 4 diameters of straight pipe. System installed with solar, or setup for the future addition of solar heating equipment by installing 18 inches of horizontal or vertical pipe after the filter and before a heater, or built-‐in or built-‐up connections, or dedicated pipe to and from the pool. Directional inlets for mixing pool water. ANSI/APSP/ICC 15 ENERGY EFFICIENCY COMPLIANCE INFORMATION FOR RESIDENTIAL SWIMMING POOLS Requirements Heaters Heater has no pilot light Readily accessible on-‐off switch mounted outside of the heater No electric resistance heating unless for inground spa with tight fitting cover with R-‐6 insulation, or for pool with 60% of documented pool heating from on-‐site solar or recovered energy. Heater efficiency: gas/oil fired heater efficiency at least 78%, heat pump COP at least 4.0 4 4 4 4 4 4 4 4 4 4 06/18/2019