Loading...
HomeMy WebLinkAboutFile Documents.401 E Cooper Ave.0063.2018 (5).ACBK980 S. Isabella Rd. Mt. Pleasant, Michigan 48858 Phone: 800-733-8948 or 989-773-7981 Fax: 800-669-0619 www.delfield.com Exterior bottom shall be heavy-gauge galvanized metal. Exterior ends shall be heavy-gauge stainless steel. Exterior top shall be one-piece, heavy-gauge stainless steel with front edge turned down to form nosing and rear edge turned down. Base interior shall be one-piece thermoformed ABS plastic material, with integral shelf supports. ABS interior is backed by a limited lifetime warranty. Base shall be fully insulated with high-density foamed- in-place environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming Potential) polyurethane. Door shall have a heavy-gauge stainless steel exterior, with a thermoformed ABS plastic interior liner, and shall be fully insulated with foamed-in-place polyurethane. Door handle shall be black, recessed ABS. Cabinet shall have (2) adjustable epoxy-coated wire shelves installed. Refrigeration system shall use R290 refrigerant. Compressor shall be 1/5 h.p., with condenser coil and hot gas condensate evaporator mounted on rear of cabinet. Evaporator coil and temperature control shall be mounted on the interior rear wall of the cabinet. Refrigerant flow shall be controlled by a capillary tube. Cabinet shall maintain 36°F to 40°F (2°C to 4°C) interior cabinet temperature. Electrical connections shall be 115 volt, 60 Hertz, single phase. Unit shall have a 6’ (1.8m) long electrical cord and NEMA 5-15P plug. Cord and plug shall be located on rear of cabinet, 16” (40.6cm) above floor, 5” from the left side. Equipment is shipped with 2” (5cm) diameter casters installed. Specifications Standard Features Options & Accessories•Features Delfield’s exclusive ABS interior. ABS is extremely durable - It won’t dent, chip or corrode and is backed by a limited lifetime warranty •Stainless steel front, sides and top •Two epoxy coated wire shelves, standard installed per unit •Environmentally friendly R290 refrigerant •Foamed in place environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming Potential) polyurethane cuts energy costs •Black recessed quick grip handle •6’ cord and plug supplied •Door is field reversible. Standard hinging provided is on the right side •Three year parts and labor warranty and an additional two year compressor parts warranty •406P-STAR2 - 115V Undercounter refrigerator single section on casters Models 400P Series 406P Self-Contained Compact Undercounter Refrigerator - Starbucks 400P Series: 406P Self-Contained Compact Undercounter Refrigerator - Starbucks•Stainless steel back •Plastic laminate on front •Additional wire shelves •Stainless steel single-tier overshelf •5” (13cm) diameter casters •Model 409 stacking collar (adds 4” to overall combined height for use with models 406/407) •Door lock 406P-STAR2 10267 - R290 model 10267 - R290 model 5/21/2018 980 S. Isabella Rd. Mt. Pleasant, Michigan 48858 Phone: 800-733-8948 or 989-773-7981 Fax: 800-669-0619 www.delfield.com 2" Polyex SwivalCasters W/ 150 Lb RatingFront W/ BrakeRear W/o BrakeQty-4 27.25”69.2cm 32.00” 81.3cm 2.50”6.4cm 28.50”72.4cm 1.00”2.5cm 24.38”61.9cmOpening 22.62”57.5cmOpening 6.00” 2.75” 3.75” 4.00” 17.05”43.3cmDepth 19.44” 49.4cmDepth A A 72” 183cm Nema Plug5-15p 115V units only 1.00” 2.5cmClearance 3.00” 7.6cmClearance 1.00”2.5cmClearance 16.00”41cm Printed in the U.S.A. 5880_DEL_406PSTAR2 05/15400P Series406P Self-Contained Compact Undercounter Refrigerator - StarbucksInstallation Note: Refrigeration system is designed so that air will flow under the unit, through the compressor area, and out the top rear of the unit. Any restriction to this air flow path will void the warranties. Side Clearances Front Elevation Front Elevation Interior Front Clearance Dimensions Side View Side Interior Standard Door Hinging Is On Right May be reversed to left in the field Door Clearance Detail 24.75"63 cm Standard Door Hinging Is On Right Specifications Model V/Hz/Ph # of Shelves Shelf Area Volume H.P.Amps NEMA Plug Ship Weight Total Watts Energy (KWH/Day) 406P-STAR2 115/60/1 2 4.6ft2 5.7ft3 1/5 4.0 5-15P 168lbs (76kg)-1.16 10267 - R290 model 10267 - R290 model 5/21/2018 980 S. Isabella Rd. Mt. Pleasant, Michigan 48858 Phone: 800-733-8948 or 989-773-7981 Fax: 800-669-0619 www.delfield.com Exterior top shall be one-piece, 22-gauge stainless steel with front edge turned down to form nosing and rear edge turned down. Exterior bottom shall be one-piece, 14-gauge galvanized metal. Exterior ends shall be 22-gauge stainless steel. Base interior shall be one-piece thermoformed ABS plastic material, with integral shelf supports. ABS interior is backed by a limited lifetime warranty. Cabinet shall have (4) epoxy- coated wire shelves installed. Base shall be fully insulated with high-density foamed-in-place environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming Potential) polyurethane. Doors shall have a 22-gauge stainless steel exterior, with a thermoformed ABS plastic interior liner, and shall be fully insulated with foamed-in-place polyurethane. Door handles shall be black, recessed ABS. Refrigeration system shall use R290 refrigerant. Compressor shall be 1/5 h.p., with condenser coil and hot gas condensate evaporator mounted on rear of cabinet. Evaporator coil and temperature control shall be mounted on the interior rear wall of the cabinet. Refrigerant flow shall be controlled by a capillary tube. Cabinet shall maintain 36°F to 40°F (2°C to 4°C) interior cabinet temperature. Electrical connections shall be 115 volt, 60 Hertz, single phase. Unit shall have a 6’ (1.8m) long electrical cord and NEMA 5-15P plug. Cord and plug shall be located on rear of cabinet, 16” (40.6cm) above floor, 12” from left side. 220v, 50Hz electrical system is optional. Equipment is shipped with 2” (5cm) diameter casters installed. Specifications Standard Features Options & Accessories•Features Delfield’s exclusive ABS interior. ABS is extremely durable - it won’t dent, chip or corrode and is backed by a limited lifetime warranty •Stainless steel front, sides and top •Environmentally friendly R290 refrigerant •Fully insulated with high-density foamed- in-place environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming Potential) polyurethane •Four epoxy coated wire shelves standard installed per unit •Black recessed quick grip handle •Door hinging available on either right or left, right side is standard •6’ cord and plug supplied •Three year parts and labor warranty and an additional two year compressor parts warranty •UC4048P-STAR - 115V Starbucks two section undercounter refrigerator Models UC4000P Series Self-Contained Compact Undercounter Refrigerator - Starbucks UC4000P Series: Self-Contained Compact Undercounter Refrigerator - Starbucks•Stainless steel back •Plastic laminate on front •Additional wire shelves •3” (7.6cm) diameter casters •5” (13cm) diameter casters •Door lock UC4048P-STAR 10473 - R290 model 10473 - R290 model 5/21/2018 980 S. Isabella Rd. Mt. Pleasant, Michigan 48858 Phone: 800-733-8948 or 989-773-7981 Fax: 800-669-0619 www.delfield.com Printed in the U.S.A. 5881_DEL_UC4048PSTAR 05/15 Specifications Model V/Hz/Ph # Of Shelves Shelf Area Volume H.P.Amps NEMA Plug Ship Weight Total Watts Energy (KWH/Day) UC4048P-STAR 115/60/1 4 8.0ft2 10.80ft3 1/5 4.0 5-15P 236lbs/107kg -1.38UC4000P SeriesSelf-Contained Compact Undercounter Refrigerator - StarbucksInstallation Note: Refrigeration system is designed so that air will flow under the unit, through the compressor area and out the top rear of the unit. Any restriction to this air flow path will void the warranties. Door Clearance Detail 21.75”55.2cm Plan View 48.06” 122.07cm 28.38” 72.08cm Elevation View 2.50”6.35cm 32.00” 81.28cm 1.00” (2.54cm) Clearance on Top and Sides 3.00” (7.62cm) Clearance on Back 2.50”6.35cm 32.00”81.28cm 1.00” (2.54cm)RubberBumper Side View Interior Elevation View Interior Side View 10473 - R290 model 10473 - R290 model 5/21/2018 Specifications subject to change without notice.Chart dimensions rounded up to the nearest 1/8" (millimeters rounded up to next whole number). ROUGH-IN DATA Models: TRUE FOOD SERVICE EQUIPMENT, INC. Project Name: Location: Item #: Qty: Model #: AIA # SIS # Printed in U.S.A. APPROVALS:AVAILABLE AT: 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 Fax (636)272-2408 • Toll Free (800)325-6152 • Intl Fax# (001)636-272-7546 Parts Dept. (800)424-TRUE • Parts Dept. Fax# (636)272-9471 • www.truemfg.com 11/16 Model Doors Capacity (Cu. Ft.) (liters)Shelves Cabinet Dimensions (inches) (mm) HP Voltage Amps NEMA Config. Cord Length (total ft.) (total m) Crated Weight (lbs.) (kg)W D H* TG1R-1S-HC-LH 1 31 4 29 345/8 781/4 1/4 115/60/1 2.5 5-15P 9 405 878 737 880 1988 N/A N/A 2.74 184 * Height does not include 41/4" (108 mm) for castors and 1/4" (7 mm) for system mechanical components. TG1R-1S-HC-LH Designed using the highest quality materials and components to provide the user with colder product temperatures, lower utility costs and exceptional food safety. Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP). High capacity, factory balanced refrigeration system that maintains cabinet temperatures of 33°F to 38°F (.5°C to 3.3°C) for the best in food preservation. Stainless steel doors and front. Anodized quality aluminum exterior sides, back and bottom. NSF approved, clear aluminum interior sides and back liner. Stainless steel floor with coved corners. Adjustable, heavy duty PVC coated shelves. Positive seal self-closing door with 120° stay open feature. Lifetime guaranteed door hinges. Lifetime guaranteed recessed door handle. Entire cabinet structure and solid door are foamed-in-place using a high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP). TG1R-1S-HC-LH TG Spec Series: Reach-In Solid Swing Door Refrigerator with Hydrocarbon Refrigerant TRUE REFRIGERATIONMADE IN SINCE 1945U.S.A. ® TG1R-1S-HC-LH 10970 10970 5/21/2018 STANDARD FEATURES Model: METRIC DIMENSIONS ROUNDED UP TO THENEAREST WHOLE MILLIMETER SPECIFICATIONS SUBJECT TO CHANGEWITHOUT NOTICE PLAN VIEW TRUE FOOD SERVICE EQUIPMENT 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 • Fax (636)272-2408 • Toll Free (800)325-6152 • Intl. Fax# (001)636-272-7546 • www.truemfg.com WARRANTYThree year warranty on all parts & labor and an additional 4 year warranty on compressor.(U.S.A. only) Clip #4 goes in Hole 86 Clip #3 goes in Hole 62 12" (305 mm) 12" (305 mm) Clip #2 goes in Hole 38 Clip #1 goes in Hole 14 12" (305 mm) 12" (305 mm) 13" (331 mm) Ceiling of Cabinet Floor of Cabinet SHELVING INSTALLATION INCREMENTS See Diagram Below Starting at the bottom of the cabinet place the top of each shelf clip into the following holes: Clip #1 Hole 14 – this allows 13" (331 mm) from floor of cabinet to the top of this shelf. Clip #2 Hole 38 – this allows 12" (305 mm) from the top of the shelf below to the top of this shelf. Clip #3 Hole 62 – this allows 12" (305 mm) from the top of the shelf below to the top of this shelf. Clip #4 Hole 86 – this allows 12" (305 mm) from the top of the shelf below to the top of this shelf and 12" (305 mm) from the top of this shelf to the ceiling of the cabinet. DESIGN•True’s solid door reach-in’s are designed with enduring quality that protects your long term investment.•Designed using the highest quality materials and components to provide the user with colder product temperatures, lower utility costs and exceptional food safety. REFRIGERATION SYSTEM•Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP).•High capacity, factory balanced refrigeration system that maintains cabinet temperatures of 33°F to 38°F (.5°C to 3.3°C) for the best in food preservation.•State of the art, electronically commutated evaporator and condenser fan motors. ECM motors operate at higher peak efficiencies and move a more consistent volume of air which produces less heat, reduces energy consumption and provides greater motor reliability.•Top mounted refrigeration system with evaporator positioned out of food zone to maximize capacity. CABINET CONSTRUCTION•Exterior - stainless steel door and rainshield. Anodized quality aluminum sides, back and bottom.•Interior - NSF approved clear aluminum walls and back liner. Stainless steel floor with coved corners. •Insulation - entire cabinet structure and solid door are foamed-in-place using a high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP).•Welded, heavy duty steel frame rail, black powder coated for corrosion protection.•Frame rail fitted with 3 1/2” (89 mm) diameter castors with locks provided on front set. DOOR•Stainless steel exterior. Door opens within cabinet dimension.•Door lock standard.•Lifetime guaranteed recessed door handle. Door fitted with 12” (305 mm) long recessed handle that is foamed-in-place with a sheet metal interlock to ensure permanent attachment.•Positive seal self-closing door with 120° stay open feature. Lifetime guaranteed door hinges.•Magnetic door gasket of one piece construction, removable without tools for ease of cleaning.•Raised interior door liner and recessed door gasket for additional gasket protection. SHELVING•TG1R-1S-HC Model - Four (4) gray heavy duty PVC coated wire shelves 25" x 28 13/16 " (635 mm x 732 mm). Four (4) shelf supports included per shelf (field installed). Shelves adjustable on 6" (153 mm) increments.•Stainless steel shelf standards for additional shelf support. LIGHTING•LED interior lighting - safety shielded. MODEL FEATURES•Exterior digital temperature display, available with either °F or °C.•Evaporator epoxy coated to eliminate the potential of corrosion•NSF-7 compliant for open food product. ELECTRICAL•Unit completely pre-wired at factory and ready for final connection to a 115/60/1 phase, 15 amp dedicated outlet. 11 ft. power cord. TG1R-1S-HC-LH TG Spec Series: Reach-In Solid Swing Door Refrigerator with Hydrocarbon Refrigerant PLAN VIEW ELEVATION 781/4" (1988 mm) 821/2" (2096 mm) 41/4" (108 mm) 29" (737 mm) 345/8" (880 mm) 6111/32" (1559 mm) 2623/32" (679 mm) 10970 5/21/2018 Specifications subject to change without notice.Chart dimensions rounded up to the nearest 1/8" (millimeters rounded up to next whole number). ROUGH-IN DATA Models: TRUE FOOD SERVICE EQUIPMENT, INC. Project Name: Location: Item #: Qty: Model #: AIA # SIS # Printed in U.S.A. APPROVALS:AVAILABLE AT: 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 Fax (636)272-2408 • Toll Free (800)325-6152 • Intl Fax# (001)636-272-7546 Parts Dept. (800)424-TRUE • Parts Dept. Fax# (636)272-9471 • www.truemfg.com 11/16 Model Doors Capacity (Cu. Ft.) (liters)Shelves Cabinet Dimensions (inches) (mm) HP Voltage Amps NEMA Config. Cord Length (total ft.) (total m) Crated Weight (lbs.) (kg)W D H* TG2R-2S-HC 2 56 8 513/8 345/8 781/4 1/3 115/60/1 5.6 5-15P 9 595 1586 1305 880 1988 N/A N/A 2.74 270 * Height does not include 41/4" (108 mm) for castors and 1/4" (7 mm) for system mechanical components. TG2R-2S-HC TG2R-2S-HC Designed using the highest quality materials and components to provide the user with colder product temperatures, lower utility costs and exceptional food safety. Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP). High capacity, factory balanced refrigeration system that maintains cabinet temperatures of 33°F to 38°F (.5°C to 3.3°C) for the best in food preservation. Stainless steel doors and front. Anodized quality aluminum exterior sides, back and bottom. NSF approved, clear aluminum interior sides and back liner. Stainless steel floor with coved corners. Adjustable, heavy duty PVC coated shelves. Positive seal self-closing door with 120° stay open feature. Lifetime guaranteed door hinges. Lifetime guaranteed recessed door handle. Entire cabinet structure and solid door are foamed-in-place using a high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP). TG2R-2S-HC TG Spec Series: Reach-In Solid Swing Door Refrigerator with Hydrocarbon Refrigerant TRUE REFRIGERATIONMADE IN SINCE 1945U.S.A. ® 11083 11083 5/21/2018 STANDARD FEATURES Model: METRIC DIMENSIONS ROUNDED UP TO THENEAREST WHOLE MILLIMETER SPECIFICATIONS SUBJECT TO CHANGEWITHOUT NOTICE PLAN VIEW TRUE FOOD SERVICE EQUIPMENT 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 • Fax (636)272-2408 • Toll Free (800)325-6152 • Intl. Fax# (001)636-272-7546 • www.truemfg.com WARRANTYThree year warranty on all parts & labor and an additional 4 year warranty on compressor.(U.S.A. only) Clip #4 goes in Hole 86 Clip #3 goes in Hole 62 12" (305 mm) 12" (305 mm) Clip #2 goes in Hole 38 Clip #1 goes in Hole 14 12" (305 mm) 12" (305 mm) 13" (331 mm) Ceiling of Cabinet Floor of Cabinet SHELVING INSTALLATION INCREMENTS See Diagram Below Starting at the bottom of the cabinet place the top of each shelf clip into the following holes: Clip #1 Hole 14 – this allows 13" (331 mm) from floor of cabinet to the top of this shelf. Clip #2 Hole 38 – this allows 12" (305 mm) from the top of the shelf below to the top of this shelf. Clip #3 Hole 62 – this allows 12" (305 mm) from the top of the shelf below to the top of this shelf. Clip #4 Hole 86 – this allows 12" (305 mm) from the top of the shelf below to the top of this shelf and 12" (305 mm) from the top of this shelf to the ceiling of the cabinet. DESIGN•True’s solid door reach-in’s are designed with enduring quality that protects your long term investment.•Designed using the highest quality materials and components to provide the user with colder product temperatures, lower utility costs and exceptional food safety. REFRIGERATION SYSTEM•Factory engineered, self-contained, capillary tube system using environmentally friendly R290 hydro carbon refrigerant that has zero (0) ozone depletion potential (ODP), & three (3) global warming potential (GWP).•High capacity, factory balanced refrigeration system that maintains cabinet temperatures of 33°F to 38°F (.5°C to 3.3°C) for the best in food preservation.•State of the art, electronically commutated evaporator and condenser fan motors. ECM motors operate at higher peak efficiencies and move a more consistent volume of air which produces less heat, reduces energy consumption and provides greater motor reliability.•Top mounted refrigeration system with evaporator positioned out of food zone to maximize capacity. CABINET CONSTRUCTION•Exterior - stainless steel door and rainshield. Anodized quality aluminum sides, back and bottom.•Interior - NSF approved clear aluminum walls and back liner. Stainless steel floor with coved corners. •Insulation - entire cabinet structure and solid door are foamed-in-place using a high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP).•Welded, heavy duty steel frame rail, black powder coated for corrosion protection.•Frame rail fitted with 3 1/2" (89 mm) diameter castors with locks provided on front set. DOOR•Stainless steel exterior. Door opens within cabinet dimension.•Door lock standard.•Lifetime guaranteed recessed door handle. Door fitted with 12" (305 mm) long recessed handle that is foamed-in-place with a sheet metal interlock to ensure permanent attachment.•Positive seal self-closing door with 120° stay open feature. Lifetime guaranteed door hinges.•Magnetic door gasket of one piece construction, removable without tools for ease of cleaning.•Raised interior door liner and recessed door gasket for additional gasket protection. SHELVING•TG2R-2S-HC Model - Eight (8) gray heavy duty PVC coated wire shelves 23 1/2 ” x 28 13/16 ” (597 mm x 732 mm). Four (4) shelf supports included per shelf (field installed). Shelves adjustable on 6” (153 mm) increments•Stainless steel shelf standards for additional shelf support. LIGHTING•LED interior lighting - safety shielded. MODEL FEATURES•Exterior digital temperature display, available with either °F or °C.•Evaporator epoxy coated to eliminate the potential of corrosion•NSF-7 compliant for open food product. ELECTRICAL•Unit completely pre-wired at factory and ready for final connection to a 115/60/1 phase, 15 amp dedicated outlet. 11 ft. power cord. TG2R-2S-HC TG Spec Series: Reach-In Solid Swing Door Refrigerator with Hydrocarbon Refrigerant PLAN VIEW ELEVATION 513/8" (1305 mm) 781/4" (1988 mm) 821/2" (2096 mm) 41/4" (108 mm) 513/8" (1305 mm) 345/8" (880 mm) 6111/32" (1559 mm) 2623/32" (679 mm) 11083 5/21/2018 980 S. Isabella Rd. Mt. Pleasant, Michigan 48858 Phone: 800-733-8948 or 989-773-7981 Fax: 800-669-0619 www.delfield.com Exterior top shall be one-piece, 22-gauge stainless steel with front edge turned down to form nosing and rear edge turned down. Exterior back and bottom shall be one piece 24-gauge galvanized metal. Exterior ends shall be 22-gauge stainless steel. Base interior shall be one-piece thermoformed ABS plastic material. Base shall be fully insulated with high-density foamed-in-place environmentally friendly, Kyoto Protocol Compliant, non ODP (ozone depletion potential), non GWP (global warming potential) polyurethane. Door shall have a 22-gauge stainless steel exterior, with a thermoformed ABS plastic interior liner, and shall be fully insulated with foamed-in-place environmentally friendly, Kyoto Protocol Compliant, non ODP (ozone depletion potential), non GWP (global warming potential) polyurethane. Door handle shall be black, recessed ABS. Cabinet shall have stainless steel wire rack. Field reversible door. Refrigeration system shall use R290 refrigerant. Compressor shall be 1/5 h.p., with condenser coil and hot gas condensate evaporator mounted on rear of cabinet. Evaporator coil and temperature control shall be mounted on the interior rear wall of the cabinet. Refrigerant flow shall be controlled by a capillary tube. Cabinet shall maintain 36°F to 40°F (2°C to 4°C) interior cabinet temperature. NSF7 certified for open and packaged food. Electrical connections shall be 115 volt, 60 Hertz, single phase. Unit shall have a 6’ (1.8m) long electrical cord and NEMA 5-15P plug. Cord and plug shall be located on rear of cabinet, 16” (41cm) above floor, 5” from the left side. Casters: Equipment is mounted on 2.00” (5cm) diameter swivel front locking plate casters. Rear casters are fixed. Equipment clearance above the floor is 2.50” (6cm). Installation: Unit will arrive in a 30.5”x29.5”x40.25” package. Uncrate the unit, roll it into place and plug it in. Specifications Standard Features Options & Accessories•Features Delfield’s exclusive ABS interior. ABS is extremely durable - it won’t dent, chip or corrode and is backed by a limited lifetime warranty •Stainless steel front, sides and top •Stainless steel wire rack •Environmentally friendly R290 refrigerant •Foamed in place environmentally friendly, Kyoto Protocol Compliant, non ODP (ozone depletion potential), non GWP (global warming potential) polyurethane cuts energy costs •Black recessed quick grip handle •All units come standard hinged right and may be changed at the factory at no charge. Indicate when order is placed •6’ cord and plug supplied •Field reversible door •Three year parts and labor warranty and an additional two year compressor parts warranty •406P-STAR4 Starbucks single section refrigerator Models 400P Series Self-Contained Compact Undercounter Refrigerator - Starbucks•Stainless steel back •Plastic laminate on front •Wire shelves •Stainless steel single-tier overshelf •3.5” (8.9cm) diameter casters •5” (12.7cm) diameter casters •Model 409 stacking collar adds 4” to overall combined height •Door lock 400P Series Self-Contained Compact Undercounter Refrigerator 406P-STAR4 12618 12618 5/21/2018 980 S. Isabella Rd. Mt. Pleasant, Michigan 48858 Phone: 800-733-8948 or 989-773-7981 Fax: 800-669-0619 www.delfield.com400P SeriesSelf-Contained Compact Undercounter RefrigeratorPrinted in the U.S.A. 5883_DEL_406PPSTAR4 05/15 Specifications Model Volume Ship Weight H. P.Volts Phase Amps HVAC Load NEMA Plug 406P-STAR4 5.7ft3 .16m3 168lbs 76kg 1/5 115/60/1 4.0 1430BTU/h 322W 5-15P Delfield reserves the right to make changes to the design or specifications without prior notice. 6’ 1.8m NEMA Plug 5-15P16.00” 41cm 24.75” 63cm 29.50” 75cm 27.25”69cm 2.50”6cm 32.00”81cm 1.00” 2.5cm Plan View Side ViewElevation View Door SwingWire Rack Installation Note: Refrigeration system is designed so that air will flow under the unit, though the compressor area, and out the top rear of the unit. Any restriction to this air flow path will void the warranties. 12618 5/21/2018 Specifications subject to change without notice.Chart dimensions rounded up to the nearest 1/8" (millimeters rounded up to next whole number). ROUGH-IN DATA Model: TRUE FOOD SERVICE EQUIPMENT, INC. Project Name: Location: Item #: Qty: Model #: AIA # SIS # Printed in U.S.A. APPROVALS:AVAILABLE AT: 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 Fax (636)272-2408 • Toll Free (800)325-6152 • Intl Fax# (001)636-272-7546 Parts Dept. (800)424-TRUE • Parts Dept. Fax# (636)272-9471 • www.truemfg.com T-49F STAR TRUE REFRIGERATIONMADE IN SINCE 1945U.S.A. ® T-Series: Reach-In Solid Swing Door -10ºF Freezer T-49F STAR True’s solid door reach-in’s are designed with enduring quality that protects your long term investment. Designed using the highest quality materials and components to provide the user with colder product temperatures, lower utility costs, exceptional food safety and the best value in today’s food service marketplace. Extra large evaporator coil balanced with higher horsepower compressor and large condenser maintains -10°F (-23.3°C) cabinet temperatures. Ideally suited for both frozen foods and ice cream. Stainless steel solid doors and front. The very finest stainless with higher tensile strength for fewer dents and scratches. Adjustable, heavy duty PVC coated shelves. Positive seal self-closing doors. Lifetime guaranteed door hinges and torsion type closure system. Automatic defrost system time- initiated, temperature-terminated. Saves energy consumption and provides shortest possible defrost cycle. Bottom mounted units feature: ”No stoop” lower shelf. Storage on top of cabinet. Compressor performs in coolest, most grease free area of kitchen. Easily accessible condenser coil for cleaning. Model Doors Shelves Cabinet Dimensions (inches) (mm) HP Voltage Amps NEMA Config. Cord Length (total ft.) (total m) Crated Weight (lbs.) (kg)L D H* T-49F STAR 2 5 541/8 291/2 783/8 3/4 115/60/1 11.0 5-20P 9 480 1375 750 1991 3/4 230-240/50/1 4.8 ▲2.74 218 * Height does not include 5" (127 mm) for castors or 6" (153 mm) for optional legs.▲Plug type varies by country. 4/13 13682 5/21/2018 STANDARD FEATURES Model: METRIC DIMENSIONS ROUNDED UP TO THENEAREST WHOLE MILLIMETER SPECIFICATIONS SUBJECT TO CHANGEWITHOUT NOTICE KCL TRUE FOOD SERVICE EQUIPMENT 2001 East Terra Lane • O’Fallon, Missouri 63366-4434 • (636)240-2400 • Fax (636)272-2408 • Toll Free (800)325-6152 • Intl. Fax# (001)636-272-7546 • www.truemfg.com PLAN VIEW T-49F STAR DESIGN•True’s commitment to using the highest quality materials and oversized refrigeration systems provides the user with colder product temperatures, lower utility costs, exceptional food safety and the best value in today’s food service marketplace. REFRIGERATION SYSTEM•Factory engineered, self-contained, capillary tube system using environmentally friendly (CFC free) R404A refrigerant.•Extra large evaporator coil balanced with higher horsepower compressor and large condenser; maintains -10°F (-23.3°C). Ideally suited for both frozen foods and ice cream.•Sealed, cast iron, self-lubricating evaporator fan motor(s) and larger fan blades give True reach-in’s a more efficient low velocity, high volume airflow design. This unique design ensures faster temperature recovery and shorter run times in the busiest of food service environments.•Bottom mounted condensing unit positioned for easy cleaning. Compressor runs in coolest and most grease free area of the kitchen. Allows for storage area on top of unit.•Automatic defrost system time-initiated, temperature-terminated. Saves energy consumption and provides shortest possible defrost cycle. CABINET CONSTRUCTION•Exterior - Stainless steel front. Anodized quality aluminum ends, back and top.•Interior - attractive, NSF approved, white aluminum liner. Stainless steel floor with coved corners.•Insulation - entire cabinet structure and solid doors are foamed-in-place using Ecomate. A high density, polyurethane insulation that has zero ozone depletion potential (ODP) and zero global warming potential (GWP).•Welded, heavy duty steel frame rail, black powder coated for corrosion protection.•Frame rail fitted with 4" (102 mm) diameter stem castors - locks provided on front set. DOORS•Stainless steel exterior with white aluminum liner to match cabinet interior. Doors extend full width of cabinet shell. Door locks standard.•Lifetime guaranteed recessed door handles. Each door fitted with 12" (305 mm) long recessed handle that is foamed-in-place with a sheet metal interlock to ensure permanent attachment.•Positive seal self-closing doors. Lifetime guaranteed door hinges and torsion type closure system.•Magnetic door gaskets of one piece construction, removable without tools for ease of cleaning. SHELVING•Five (5) adjustable, heavy duty PVC coated wire shelves 24 9/16"L x 22 3/8 "D (624 mm x 569 mm). Four (4) chrome plated shelf clips included per shelf.•Shelf support pilasters made of same material as cabinet interior; shelves are adjustable on 1/2" (13 mm) increments. LIGHTING•Incandescent interior lighting - safety shielded. Lights activated by rocker switch mounted above doors. MODEL FEATURES•Exterior temperature display.•Evaporator is epoxy coated to eliminate the potential of corrosion.•Rear airflow guards prevent product from blocking optimal airflow.•NSF-7 compliant for open food product. ELECTRICAL•Unit completely pre-wired at factory and ready for final connection to a 115/60/1 phase, 20 amp dedicated outlet. Cord and plug set included. T-Series: Reach-In Solid Swing Door -10ºF Freezer Model Elevation Right Plan 3D Back T-49F STAR WARRANTYTwo year warranty on all parts and labor and an additional 3 year warranty on compressor. (U.S.A. only) SHELVING INSTALLATION INCREMENTSSee diagram below LEFT SIDE OF CABINET Clip #1 goes in Hole 28 from the bottom of the cabinet - this allows 17" (432mm) from the floor of cabinet to the top of this shelf. Clip #2 goes in Hole 59 from the bottom of the cabinet - this allows 17" (331mm) from the top of the shelf below to the top of this shelf. Clip #3 goes in Hole 76 from the bottom of the cabinet - this allows 9" (229mm) from the top of the shelf below to the top of this shelf and 11" (280mm) from the top of this shelf to the ceiling of the cabinet. Note: Measurements on left side of shelf standards are to top of shelves not the clips.Note: Hole numbers noted on right side of standard only include shelf clip slots and do not include holes for screws. RIGHT SIDE OF CABINET Clip #1 goes in Hole 28 from the bottom of the cabinet - this allows 17" (432mm) from the floor of cabinet to the top of this shelf. Clip #2 goes in Hole 59 from the bottom of the cabinet - this allows 17" (331mm) from the top of the shelf below to the top of this shelf and 20" (508mm) from the top of this shelf to the ceiling of the cabinet. Note: Measurements on left side of shelf standards are to top of shelves not the clips. Note: Hole numbers noted on right side of standard only include shelf clip slots and do not include holes for screws. CeilingLeft Side of Cabinet Right Side of Cabinet Clip #2 goes in Hole 59 (both sides) Clip #3 goes in Hole 76 (left side only) Clip #1 goes in Hole 28 (both sides) Floor of Cabinet 9" (229 mm) 17" (432 mm) 17" (432 mm) 17" (432 mm) 17" (432 mm) 5/21/2018 Project ______________________________________ Item _________________________________________ Quantity ____________________________________ CSI Section 11400 Approved ___________________________________ Date _________________________________________ Standard Features • On-demand gas infusion system ideal for coffee, tea, dairy, and other beverages • Three In-line gas infusion systems allows for still and nitrogenated beverages to be poured from the same source through different taps • Refrigerated base cabinet and remote chiller (Multiplex Beermaster 75) circulates glycol in conduit to insure that product is kept below 41°F for a cool, consistent pour • Four taps allow for dispense of (1) still and (3) infused beverages from three kegs (PN 3547976) stored in base • Tower is remotely mounted on countertop via 25ft of insulated and glycol-cooled beverage conduit • Drip pan mounted below tower, plumbed to nearby drain • Compatible with food grade nitrogen, mixed gas (food-grade nitrogen & cabon dioxide), and carbon dioxide • Customizable tap handles • Quick connects for on-site, food-grade gases • All NSF-approved materials • Approved for dairy • ND31RS30 Models Nitro Dispensing System GENERATION 2.0 Nitro Dispensing System - Generation 2.0www.multiplexbeverage.com 6312C 3/18 Tel: +1 812.246.7000 Fax: +1 812.246.7024 2100 Future Drive Sellersburg, IN 47172 USA 17588 5/21/2018 Welbilt reserves the right to make changes to the design or specifications without prior notice. Nitro Dispensing System - ND31RS30 Standard Features Refrigerated base cabinet, in-line gas infusion, pressure gauges, thermostat, four TRUpour taps for still and nitro dispense on shared tower, drip pan with plumbed drain Shipping Weight 745 lbs. / 338 kgs. Weight (dry)471 lbs. / 214 kgs. Electrical Requirements 120V/60Hz / 7 FLA - 15 Amp Circuit Remote Chiller Multiplex Beermaster 75 (S0907531-161) with glycol kit (00214510), wall mount rack (00214299) Glycol Conduit Length 50 ft. (15.2 m) maximum - 2.875" (7.3 cm) OD (PN 3540084) Tower Conduit Length 25 ft. (7.6 m) maximum - 3.125" (7.9 cm) OD (PN 3239844) Drain Pan Surface mount, plumbed to nearby drain, 36 fl. oz. capacity In line filter (3) Filters w/ 250 mesh, 40 micron allowance Heat of Rejection (Cabinet base)902 BTU/hr (X kW) Gas Types Food-grade (stored on premises) - Nitrogen, Carbon Dioxide, mixed gas CO2/N2 Maximum Gas Pressure 90 psig Product Storage (3) 3-gallon steel ball-lock tanks (PN 3547976) - All active, sold separately Nitro Dispensing System - Generation 2.0www.multiplexbeverage.com 6312C 3/18 Tel: +1 812.246.7000 Fax: +1 812.246.7024 2100 Future Drive Sellersburg, IN 47172 USA Clearances - Base Cabinet Right Side 5" (12.7 cm)* Left Side 0" (0.0 cm) Back 5" (12.7 cm)* Front (Door Swing)32" (81.3 cm) Top Tower Location Dependent Taps and Tower Side View Drain Pan Top View Refrigerated Base Left or right hinged doors available, must be specified at time of order. Specifications * Either Right Side or Back clearance must be 5" to accomodate beverage conduit, but not both. Other clearance may be 0". 5/21/2018 General Operating Tips Features 1 Postion Soft Heat Server Stand •Remote server docking station for additional satellite coffee service •Server stand to be used with SH servers for remote serving and to obtain proper faucet to counter clearance •LED power indicator shows server is operational •Docking stations have instant power contact with servers •Includes drip tray as shown 1SH Server Stand Electrical Hook-Up CAUTION - Improper electrical installation will damage electronic components. •Attach legs provided •Plug unit into correct electrical •To assure power is on, place server on unit, Red LED indicator on server should illuminate •Provides power to internal heater for the Soft Heat server Starbucks® 1 Position Soft Heat® Server Stand 01/1710312 10312 5/21/2018 BUNN® practices continuous product research and improvement. We reserve the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Dimensions & Specifications Bunn-O-Matic® Corporation - 5020 Ash Grove Drive, Springfield, Illinois 62711 • 800-637-8606 • 217-529-6601 • www.bunn.com All dimensions shown in inches and millimeters. Model Product # Volts Amps Total Capacity Cubic Shipping Cord AgencyWatts Size Weight Attached 1SH Stand 27825.0017 120 .75 90 1 SH Server 1.7ft3 13 lbs No 1SH Stand 27825.0014 100 .63 75 1 SH Server .03m3 5.9 kg No Electrical: 120V model is 2-wires plus ground service rated at 120V, single phase 60 Hz. 220-230V model is 2-wires plus ground service rated at 220-230V, single phase 50/60 Hz. 100V model is 2-wires plus ground service rated rated at 100V, single phase 50/60 Hz. 1/17 © Bunn-O-Matic Corporation 8.4 [ 213.36 ] 11.6 [ 294.64 ] 7.5 [ 190.5 ] 7.2 [ 182.88 ] 7.2 [ 182.88 ] 1.44 [ 36.576 ] 1.44 [ 36.576 ] 8.7 [ 220.98 ] 10.1 [ 256.54 ] 13.2 [ 335.28 ] 10.1 [ 256.54 ] 4.1 [ 104.14 ] POWER CORD (NEMA 5-15P PLUG) 1.75 ADJUSTABLE UL LISTED 10312 5/21/2018 Related Products Features 08/15 Starbucks® Digital Brewing System •Three batch size capability •Stores individual coffee and flavor profiles using adjustable water volume, bypass percentage, pulse-brew, and pre-infusion timing • Operate any combination of equipment error-free with wireless brewer-grinder interface via Smart Funnel® • Reduce accidents with safety features that decrease hot splashes from funnel • Stops brewing when funnel is not present. • Consistently brew perfect coffee using Digital Brewer Control® • Server heat control automatically shuts off once target temperature is reached • Universal side-mounted hot water dispenser for optional attachment to either side of brewer. • Large capacity tank drain •Includes drip tray as shown Dual SH DBC with 1.5 gallon (5.7 L) SH-S Servers (servers sold separately) Electrical Hook-Up CAUTION - Improper electrical installation will damage electronic components 1. An electrician must provide electricalservice as specified. 2.Using a voltmeter, check the voltage andcolor coding of each conductor at theelectrical source. 3. Remove the front panel beneaththe sprayheads. 4.Feed the cord through the strain reliefand connect it to the terminal block. 5.Connect the brewer to the power sourceand verify the voltage at the terminal blockbefore proceeding. Replace the front panel. 6.If plumbing is to be hooked up later, besure the brewer is disconnected from thepower source. If plumbing has beenhooked up, the brewer is ready forinitial set-up. PLUMBING REQUIREMENTS - This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1/2” or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 1/4” flare or female quick connect. NOTE - Bunn-O-Matic recommends 1/4” copper tubing for installations of less than 25 feet (7.62 M) and 3/8” for more than 25 feet (7.62 M) from the 1/2” water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the coun-ter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow. This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA). PLUMBING HOOK-UP1. Flush the water line and securely attachit to the flare fitting located on bottomof brewer. 2.Turn on the water supply. 1. Confirm server is clean and empty 2.Funnel should contain filter and propercoffee amount 3.Press “On/Off” switch 4.Select desired batch size 5.Press “Brew” General Operating Tips Starbucks® Dual Soft Heat® DBC® Brewer 10746 10746 5/21/2018 BUNN® practices continuous product research and improvement. We reserve the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Dimensions & Specifications Bunn-O-Matic® Corporation - 5020 Ash Grove Drive, Springfield, Illinois 62711 • 800-637-8606 • 217-529-6601 • www.bunn.com All dimensions shown in inches and millimeters. Model Product # Volts Amps Total Brewing Cubic Shipping Cord AgencyWatts Capacity/hr Size Weight Attached Dual SH DBC 33500.0056 120/208 40.1 8200 22.8 gal. 13ft3 98 lbs No Dual SH DBC 33500.0051 120/240 35.0 8200 22.8 gal. .37m3 98 lbs No Dual SH DBC 33500.0052 230 30.9 7100 74.5 L .37m3 44.5 kg No Dual SH DBC 33500.0053 200 24.0 8300 90.1 L .37m3 44.5 kg No Dual SH DBC 33500.0054 400 16.0 11,125 119.2 L .37m3 44.5 kg No Dual SH DBC 33500.0055 220 25.5 5600 68.5 L .37m3 44.5 kg No Note: Soft Heat® Brewers and Servers are boxed and shipped separately. Electrical: 120/208V brewer is 3-wires plus ground service rated at 120/208V, single phase 60 Hz. 120/240V brewer is 3-wires plus ground service rated at 120/240V, single phase 60 Hz. 230V brewer is 2-wires plus ground service rated at 230V, single phase 50/60 Hz. 200V brewer is 3-wires plus ground service rated at 200V, three phase 50/60 Hz. 400V brewer is 4-wires plus ground service rated at 230-400V, three phase 50/60 Hz. 220V brewer is 2-wires plus ground service rated at 220V, single phase 60 Hz. Plumbing: 20-90 psi (69-621 kPa). Machine supplied with 3/8” compression fitting. 1/17 © Bunn-O-Matic Corporation 2.0[ 50.8mm ] 32.0[ 812.8mm ] 2.4[ 61.0mm ] 17.9[ 454.7mm ]6.7[ 120.2mm ] 7.3[ 185.4mm ]8.6[ 218.4mm ] 17.9[ 454.7mm ] 20.1[ 510.5mm ] 11.1[ 281.9mm ] 1.1[ 27.9mm ]15.8[ 401.3mm ] 4.0[ 101.6mm ]ADJUSTABLE LEGS SH SERVER WATER SUPPLY 18.0[ 457.2mm ] UL LISTED UL LISTED 10746 5/21/2018 retail grinder KR 1203 Fast and reliable 10808 10808 5/21/2018 Ditting Maschinen AG Länggenstrasse 34 | CH-8184 Bachenbülach | Switzerland Phone +41 44 864 18 00 | Fax + 41 44 864 18 01 info@dittingswiss.ch | www.dittingswiss.ch TECHNICAL DATA Voltage/frequency/phase Motor power Average grinding capacity Hopper capacity Grinding disc diameter Ø Shaker plate Sticker Ditting Basic Adjustment Net weight Dimensions (w x d x h), mm Standard colour EQUIPMENT Hopper magnet Automatic bag holding device Manual bag holding device Bag shaker Cooling fan Overload protection SPECIAL EQUIPMENT Special grinding discs Slide cut-off 10 kg hopper Outlet extension Overload protection Standard 1203 - Art.No.262206 220-240V/50Hz/1 1.4 kW 1400 g/min 1100 g 120 mm shaking 1 left, 1 right 3 spike 38 kg 260 x 340 x 640 black • – •••• –•• – – 1203 - Art.No.262207 220V / 60Hz 1.4 kW 1400 g/min 1100 g 120 mm shaking 1 left, 1 right 13 spike 38 kg 260 x 340 x 640 black • – •••• –•• – – 1203 - Art.No. 262209 230 V / 50Hz Engl. UK-St 1.4 kW 1400 g/min 1100 g 120 mm shaking 1 left, 1 right 13 spike 38 kg 260 x 340 x 640 black • – •••• –•• – – The KR 1203 model is the ideal solution everywhere that fast, reliable and uniform grinding is required. Coffee stores with a large volume of business, supermarkets and roasting establishments value these coffee grinders highly for their exceptional performance, sturdiness and simple and safe operation. •Specially developed motors allowing large grinding capacity at all degrees of fineness •Preservation of coffee’s unique aromatic oils thanks to uniform, gentle and cool grinding made possible by specially sharpened discs developed by Ditting •Continuously variable adjustment of grinding fineness. •Minimal coffee particles left in discharge tube thanks to built-in vibrating device or manual tapper •Efficient bag shaking device distributes grounds evenly into bag and ensures all particles are dispensed •Precision grinding discs made of high quality material that is extremely wear resistant. The original discs can be re-sharpened up to 2-3 times with proper care and maintenance •Easy to maintain and clean StarbuckS SpecificationS: retail grinder KR 1203 10808 5/21/2018 General Operating Tips Features Soft Heat Server •Remote server docking station for additional satellite coffee service •Server stand to be used with SH servers for remote serving and to obtain proper faucet to counter clearance •LED power indicator shows server is operational •Docking stations have instant power contact with servers •Includes drip tray as shown 1.5 Gallon SH Server Electrical Hook-Up CAUTION - Improper electrical installation will damage electronic components. •Attach legs provided •Plug unit into correct electrical •To assure power is on, place server on unit, Red LED indicator on server should illuminate •Provides power to internal heater for the Soft Heat server Starbucks® 1.5 Gallon Soft Heat® Server 01/1710856 10856 5/21/2018 BUNN® practices continuous product research and improvement. We reserve the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. Dimensions & Specifications Bunn-O-Matic® Corporation - 5020 Ash Grove Drive, Springfield, Illinois 62711 • 800-637-8606 • 217-529-6601 • www.bunn.com All dimensions shown in inches and millimeters. Model Product # Capacity Cubic Shipping Net Ready• Cord AgencySize Weight Weight Weight Attached SH-S Server 27850.0048 1.5 Gallon 2.2ft3 13.7 lbs 11 lbs 22 lbs N/A 5.7 L .06 m3 6.2 kg 5.0 kg 9.9 kg Electrical: 120V model is 2-wires plus ground service rated at 120V, single phase 60 Hz. 220-230V model is 2-wires plus ground service rated at 220-230V, single phase 50/60 Hz. 100V model is 2-wires plus ground service rated rated at 100V, single phase 50/60 Hz. 1/17 © Bunn-O-Matic Corporation 11.2 [ 284.48 ] 3.3 [ 83.82 ] 4.0 [ 101.6 ] 11.8 [ 299.72 ] 12.8 [ 325.12 ] 13.9 [ 353.06 ] 8.5 [ 215.9 ] 9.7 [ 246.38 ] 1.6 [ 40.64 ]POWER ON INDICATOR/FLASHING LAMP UL LISTED 10856 5/21/2018 PERFORMANCE Utilizing TurboChef’s patented technology to rapidly cook food without compromis- ing quality, the NGO provides superior cooking performance while requiring less space and consuming less energy. THE NGOTM EXTERIOR CONSTRUCTION n Powder coated, corrosion-resistant steel outer wrap and door n Die-cast aluminum front panels with matte-nickel accents n Cool-to-touch exterior; all surfaces below 50°C n Ergonomic matte-nickel door handle n 4-inch nickel-plated legs INTERIOR CONSTRUCTION n 201/304 stainless steel n Fully welded and insulated cook chamber n Removable rack and lower jetplate STANDARD FEATURES n Independently-controlled dual motors for vertically-recirculated air impingement n Top-launched microwave system n Stirrer to help ensure even distribution of air and microwave n Integral recirculating catalytic converter for UL 710B (KNLZ) listed ventless operation n External air filtration n Vent catalyst to further limit emissions and odors n Smart menu system capable of storing up to 1,024 recipes n Flash firmware updates via smart card n Single or multiple-temperature interface n Built-in self-diagnostics for monitoring oven components and performance n Compatible with Oven ConnectTM and ChefComm Pro® n Smart Voltage Sensor Technology* (U.S. only) n Stackable (requires stacking stand) n Includes plug and cord (6 ft. nominal) n Warranty – 1 year parts and labor n CAT 5 Connection COMES WITH STANDARD ACCESSORIES n 1 Bottle Oven Cleaner (103180) n 1 Trigger Sprayer (103182) n 1 Hard Anodized Cooking Tray (i1-9496) 1. Blower Motors 2. Microwave System 3. Stirred Impinged Air (Top) and Microwave 4. Impinged Air (Bottom) 5. Catalytic Converter 6. Impingement Heater 7. Vent Tube Catalyst 8. Air Filter 9. Inlet Air for Cooling Electronic Components 2 3 4 65 7 8 9 1 1 SPECIFICATION SHEET VENTILATION n UL 710B (KNLZ) listed for ventless operation.† n EPA 202 test (8 hr): - Product: Pepperoni Pizzas - Results: 0.64 mg/m 3 - Ventless Requirement: <5.00 mg/m3 n Internal catalytic filtration to limit smoke, grease, and odor emissions.NGO TM FOR STARBUCKS COFFEE COMPANYDOC-1143/Revision P/April 2017 This product conforms to the ventilation recommendations set forth by NFPA96 using EPA202 test method. * Smart Voltage Sensor Technology does not compensate for lack of or over voltage situations. It is the responsibility of the owner to supply voltage to the unit according to the specifications on the back of this sheet. † Ventless certification is for all food items except for foods classified as “fatty raw proteins.” Such foods include bone-in, skin-on chicken, raw hamburger meat, raw bacon, raw sausage, steaks, etc. If cooking these types of foods, consult local HVAC codes and authorities to ensure compliance with ventilation requirements. Ultimate ventless allowance is dependent upon AHJ approval, as some jurisdictions may not recognize UL certification or application. If you have questions regarding ventless certifications or local codes please email ventless.help@turbochef.com TurboChef reserves the right to make substitutions of components or change specifications without prior notice. 12407 12407 5/21/2018 DIMENSIONS SINGLE UNIT Height 25.0”635 mm Width 16.0”406 mm Depth 29.8”757 mm Weight 170 lb.77.1 kg COOK CHAMBER Height 7.2”183 mm Width 12.5”317 mm Depth 10.5”266 mm Volume 0.54 cu.ft.15.4 liters WALL CLEARANCE (Oven not intended for built-in installation) Top 5”127 mm Sides*2”51 mm SHIPPING INFORMATION U.S.: All ovens shipped within the U.S. are packaged in a double-wall corrugated box banded to a wooden skid. International: All International ovens shipped via Air or Less than Container Loads are packaged in wooden crates. Box size: 37” x 24” x 37” (940 mm x 610 mm x 940 mm) Crate size: 38” x 26” x 38” (965 mm x 660 mm x 965 mm) Item class: 110 NMFC #26710 HS code 8419.81 Approximate boxed weight: 205 lb. (93 kg) Approximate crated weight: 275 lb. (125 kg) Minimum entry clearance required for box: 24.5” (622 mm) Minimum entry clearance required for crate: 26.5” (673 mm) ELECTRICAL SPECIFICATIONS SINGLE PHASE US/Canada SKU: 011005333 / i1-9500-20 208/240 VAC, 60 Hz, 30 amps (Max Circuit Requirements: 30 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005788 / i1-9500-21-UK 230 VAC, 50 Hz, 27 amps (Max Circuit Requirements: 32 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005806 / i1-9500-25-BK 220 VAC, 60 Hz, 28 amps (Max Circuit Requirements: 30 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005796 / i1-9500-26-LA 220 VAC, 60 Hz, 28 amps (Max Circuit Requirements: 30 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005797 / i1-9500-27-JK 200 VAC, 50 Hz, 30 amps (Max Circuit Requirements: 30 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005807 / i1-9500-29-JK 200 VAC, 60 Hz, 30 amps (Max Circuit Requirements: 30 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW MULTIPHASE International SKU: 011005790 / i1-9500-22-ED 230 VAC, 50 Hz, 20 amps (Max Circuit Requirements: 30 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005793 / i1-9500-23-EW 400 VAC, 50 Hz, 16 amps (Max Circuit Requirements: 20 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005799 / i1-9500-28-JD 200 VAC, 50 Hz, 20 amps (Max Circuit Requirements: 30 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005808 / i1-9500-30-JD 200 VAC, 60 Hz, 20 amps (Max Circuit Requirements: 30 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005779 / i1-9500-31-KW 400 VAC, 60 Hz, 16 amps (Max Circuit Requirements: 20 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW International SKU: 011005784 / i1-9500-32-SD 230 VAC, 60 Hz, 20 amps (Max Circuit Requirements: 30 amps) Max Input: 6.2 kW / MW: 3.2 kW / HTR: 6.0 kW 11.8” (299.7 mm) 16.0” (406 mm) 21.0” (533 mm) 4.0”(102 mm) 25.0” (635 mm) 18.5” (470 mm) 4.2” (107 mm) 27.3” (693 mm) 10.7” (272 mm)25.9” (658 mm) 39.1” (993 mm) US, CAN, LA (2L + G / NEMA 6-30P) 2.5” (64 mm) 2.5” (64 mm) UK, BK, JK (L + N + G) ED, BD, JD, SD (3L + G) EW, KW (3L + N + G)NGO TM FOR STARBUCKS COFFEE COMPANY© 2009–2017 TurboChef Technologies, Inc. * Side clearance required for electrical component ventilation.TurboChef Global Operations 2801 Trade Center Drive | Carrollton, Texas 75007 USA US: 800.90TURBO (800.908.8726) | International: +1 214.379.6000 Fax: +1 214.379.6073 | www.turbochef.com TurboChef recommends a type D circuit for European installations. 12407 5/21/2018 Engineered to provide dramatic sound reduction, world class reliability, unparalleled speed of service and a perfect blend every time. INNOVATIVE DESIGN Our Quietest Blender Innovative vibration dampening technology creates Vitamix quality drinks in a more enjoyable customer atmosphere. Magnetically Secured Floating Sound Enclosure Dramatically easier to clean and disassemble. No screws to damage the enclosure. No parts to lose. Ultimate Blending Flexibility and Optimization Variable speed control and automatic shut-off provide flexibility in creating endless recipes. The 4 program buttons (capability for 6) with 34 optimized programs in memory provide operators with easy, consistent drinks every time. Custom blending programs can easily be created for signature drinks. Improved Speed of Service The Advance™ container design reduces blend and pour time for faster customer service. Designed for High Performance and Durability Air management and powerful ≈ 3 peak output HP motor reduces noise, improves reliability and reduces down time. www.vitamix.com THE QUIET ONE™ 12508 5/21/2018 On Counter Blender (Argentina Only) Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (Argentina Only) Starbucks: #11012099 Vitamix: #051025-2657 Motor: ≈ 2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Argentina Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com ©2016 Vita-Mix® Corporation 11/16 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm 5/21/2018 On Counter Blender Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender Starbucks: #11012097 Vitamix: #051025-2387 Motor: ≈ 2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Asia / South Pacific Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com ©2016 Vita-Mix® Corporation 11/16 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm Asia / South Pacific plug configuration applies to the following countries: Australia Fiji New Zealand 5/21/2018 On Counter Blender (Brazil Only) Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (Brazil Only) Starbucks: #11012113 Vitamix: #051025-2663 Motor: ≈ 2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Brazilian Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com ©2016 Vita-Mix® Corporation 11/16 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm 5/21/2018 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com ©2016 Vita-Mix® Corporation 11/16 On Counter Blender (Canada Only) Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 15 A, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (Canada Only) Starbucks: #11010765 Vitamix: #040016 Motor: ≈ 2 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 10 A, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Canadian Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. 5/21/2018 On Counter Blender (China Only) Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (China Only) Starbucks: #11017541 Vitamix: #051037 Motor: ≈ 2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm China Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm ©2016 Vita-Mix® Corporation 11/165/21/2018 On Counter Blender (Denmark Only) Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (Denmark Only) Starbucks: #11012104 Vitamix: #051025-2655 Motor: ≈ 2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Danish Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm ©2016 Vita-Mix® Corporation 11/165/21/2018 On Counter Blender Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender Starbucks: #11012095 Vitamix: #051025-2386 Motor: ≈ 2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm British Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm British plug configuration applies to the following countries: Bahrain Barbados Cyprus Egypt Hong Kong Ireland Kuwait Lebanon Malaysia Oman Qatar Saudi Arabia Singapore Sri Lanka Trinidad United Arab Emirates United Kingdom ©2016 Vita-Mix® Corporation 11/165/21/2018 On Counter Blender Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender Starbucks: #11012093 Vitamix: #051025-2385 Motor: ≈ 2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Schuko Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm Schuko plug configuration applies to the following countries: Albania Austria Belgium Bolivia Bulgaria Chile Czech Republic Finland France Germany Greece Greenland Hungary Iceland India Indonesia Jordan Luxembourg Majorca Netherlands Norway Paraguay Peru Poland Portugal Romania Russia Spain Sweden Tahiti Thailand Turkey Uruguay Vietnam Yugoslavia ©2016 Vita-Mix® Corporation 11/165/21/2018 On Counter Blender (Japan Only) Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 100 V, 50/60 Hz, 1300 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (Japan Only) Starbucks: #11012003 Vitamix: #053006 Motor: ≈ 2 peak output horsepower motor Electrical: 100 V, 50/60 Hz, 900 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Japanese Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm ©2016 Vita-Mix® Corporation 11/165/21/2018 On Counter Blender (South Korea Only) Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (South Korea Only) Starbucks: #11012064 Vitamix: #051025-2660 Motor: ≈ 2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Korean Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm ©2016 Vita-Mix® Corporation 11/165/21/2018 On Counter Blender Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 15 A, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender Starbucks: #11007909 Vitamix: #040015 Motor: ≈ 2 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 10 A, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm North and South American Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm North and South American plug configuration applies to the following countries: Bahamas Belize Bermuda Brazil* Canary Islands Cayman Islands Colombia Costa Rica Dominican Rep. Ecuador El Salvador Guam Guatemala Honduras Mexico Puerto Rico United States *120V option for Brazil ©2016 Vita-Mix® Corporation 11/165/21/2018 On Counter Blender (Philippines Only) Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1300–1550 W, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (Philippines Only) Starbucks: #11012101 Vitamix: #051025-2661 Motor: ≈ 2 peak output horsepower motor Electrical: 220-240 V, 50/60 Hz, 1200–1400 W, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Philippines Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm ©2016 Vita-Mix® Corporation 11/165/21/2018 On Counter Blender (Taiwan Only) Starbucks: #TBD Vitamix: #TBD Motor:≈ 3 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 15 A, Single Phase Pack: Includes On Counter Blender with removable shroud. Net Weight: 20.0 lbs., (28.0 lbs. with box) Dimensions: Height with lid closed: 18.0 in. / 45,7 cm Height with lid open: 24.5 in. / 62,2 cm Depth with handle: 10.7 in. / 27,2 cm Width: 8.5 in. / 21,6 cm FOR COMMERCIAL USE ONLY. Warranty: The Quiet One is backed by a three-year parts and labor warranty on motor base unit. In Counter (EB) Blender (Taiwan Only) Starbucks: #11012111 Vitamix: #036301 Motor: ≈ 2 peak output horsepower motor Electrical: 120 V, 50/60 Hz, 10 A, Single Phase Pack: Includes In Counter Blender with removable shroud. Dimensions: Height with lid closed: 12.6 in. / 32,1 cm Height with lid open: 19.3 in. / 48,9 cm Height below counter: 9.6 in. / 24,5 cm Depth above counter: 9.9 in / 25,1 cm Depth below counter: 9.1 in. / 23,1 cm Width: 8.3 in / 21,1 cm Taiwan Plug Configuration Tritan Pitcher Kit Starbucks: #011072060 Vitamix: #061791 Includes five complete 36 oz. / 1,1 L containers, blade assemblies and lids. (3 dairy, 1 non dairy, and 1 soy) 36 oz. / 1,1 L Tritan Dairy Pitcher Starbucks: #011072638 Vitamix: #061785 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Non Dairy Pitcher Starbucks: #011072639 Vitamix: #061786 Complete with blade assembly and lid. 36 oz. / 1,1 L Tritan Soy Pitcher Starbucks: #011072640 Vitamix: #061787 Complete with blade assembly and lid. Vita-Mix Corporation 8615 Usher Road Cleveland, OH 44138-2103 U.S.A. www.vitamix.com/foodservice U.S.A., Canada & Latin America: Tel: 800.4DRINK4 or 440.235.0214 E-mail: foodservice@vitamix.com All Other Countries: Tel: +1.440.782.2450 E-mail: international@vitamix.com 18.0 in. 45,7 cm 24.5 in. 62,2 cm 10.7 in. / 27,2 cm 11.5 in. / 29,2 cm8.5 in. / 21,6 cm 12.6 in. 32,1 cm 19.3 in. 48,9 cm 9.6 in. 24,5 cm 9.9 in. / 25,1 cm8.3 in. / 21,1 cm 9.1 in. / 23,1 cm ©2016 Vita-Mix® Corporation 11/165/21/2018 1 AUTOMATIC COFFEE MACHINE Cs © 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs CUT sHEETs Equip_12694_Doc1 12694 5/21/2018 2© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs sUBJECT PAGE - Cut sheet Coffee LATAM, NA 208V / 30A sKU 011011308 3 - Cut sheet Coffee APAC, LATAM 230V / 25A sKU 011011299 4 - Cut sheet Coffee APAC, LATAM 400V / 15A sKU 011011300 5 - Cut sheet Coffee EMEA 230V / 25A sKU 011011301 6 - Cut sheet Coffee EMEA 400V / 15A sKU 011011303 7 - Cut sheet Coffee China Only 220V / 25A sKU 011011304 8 - Cut sheet Coffee China Only 380V / 15A sKU 011011306 9 - Cut sheet Coffee Japan Only 200V / 30A sKU 011011307 10 - Cut sheet Coffee Water Pump 11 - 12 INDEX Equip_12694_Doc1 NOTE: 50 AMP BREAKER REQUIRED IN US & CANADA AND FOR 208V MODELS IN LATAM 5/21/2018 3© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs Dimensions: 528.6 x 603.4 x 635.7mm (WxDxH) 20.8’’ x 23.8’’ x 25’’ Weight net: approx. 171 lbs. / 78 kg (empty)Requirements: Water: The unit requires a 9/16 UNEF compression water connection. Dynamic pressure 1-5 bar / 15-75 psi. El. equipment: 208V / 50/60Hz / 2PE Power: 6200 W Current: 30.0 A Power cord: US 3 x AWG 8 AUTOMATIC COFFEE MACHINE MAsTRENA sKU# 011011308 LATAM, NA (208V / 30A) 603,4mm 23,8" 528,6mm20,8"418mm16,5"77mm 3,0" 325mm 12,8"635,7mm25,0"(Remove for double machine) Chlorine Less than 0.5ppm Langelier Saturation Index -1.5 to 1.0 TDS 50 to 500 Hardness 90-140ppm pH 6.5 to 8.5 Alkalinity 20 to 140ppm Iron Less than 0.3ppm Equip_12694_Doc1 NOTE: 50 AMP BREAKER REQUIRED IN US & CANADA AND FOR 208V MODELS IN LATAM 5/21/2018 4© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs AUTOMATIC COFFEE MACHINE MAsTRENA sKU# 011011299 APAC, LATAM (230V / 25A) Dimensions: 528.6 x 603.4 x 635.7mm (WxDxH) 20.8’’ x 23.8’’ x 25’’ Weight net: approx. 171 lbs. / 78 kg (empty)Requirements: Water: The unit requires a 9/16 UNEF compression water connection. Dynamic pressure 1-5 bar / 15-75 psi. El. equipment: 230V / 50/60Hz / 2PE Power: 5600 W Current: 25.0 A Power cord: US 3 x AWG 8 603,4mm 23,8" 528,6mm20,8"418mm16,5"77mm 3,0" 325mm 12,8"635,7mm25,0"(Remove for double machine) Chlorine Less than 0.5ppm Langelier Saturation Index -1.5 to 1.0 TDS 50 to 500 Hardness 90-140ppm pH 6.5 to 8.5 Alkalinity 20 to 140ppm Iron Less than 0.3ppm Equip_12694_Doc1 5/21/2018 5© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs AUTOMATIC COFFEE MACHINE MAsTRENA sKU# 011011300 APAC, LATAM (400V / 15A) Dimensions: 528.6 x 603.4 x 635.7mm (WxDxH) 20.8’’ x 23.8’’ x 25’’ Weight net: approx. 171 lbs. / 78 kg (empty)Requirements: Water: The unit requires a 9/16 UNEF compression water connection. Dynamic pressure 1-5 bar / 15-75 psi. El. equipment: 400V / 50/60Hz / 3PNE Power: 8100 W Current: 15.0 A Power cord: US 3 x AWG 8 603,4mm 23,8" 528,6mm20,8"418mm16,5"77mm 3,0" 325mm 12,8"635,7mm25,0"(Remove for double machine) Chlorine Less than 0.5ppm Langelier Saturation Index -1.5 to 1.0 TDS 50 to 500 Hardness 90-140ppm pH 6.5 to 8.5 Alkalinity 20 to 140ppm Iron Less than 0.3ppm Equip_12694_Doc1 5/21/2018 6© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs Dimensions: 528.6 x 603.4 x 635.7mm (WxDxH) 20.8’’ x 23.8’’ x 25’’ Weight net: approx. 171 lbs. / 78 kg (empty) Requirements: Water: The unit requires a 3/8“ compression water connection. Dynamic pressure 1-5 bar / 15-75 psi. El. equipment: 230V / 50/60Hz / 2PE Power: 5600 W Current: 25.0 A Power cord: CE 3 x 4mm2 603,4mm 23,8" 528,6mm20,8"418mm16,5"77mm 3,0" 325mm 12,8"635,7mm25,0" Waterhardness German French Englisch Ppm Mval/l 1° dGH 1.0 1.79 1.25 17.8 0.357 1° fTH 0.56 1.0 0.7 10.0 0.2 1° e 0.8 1.43 1.0 14.3 0.286 1° ppm 0.056 0.1 0.07 1.0 0.02 1 mval/l 2.8 5.0 3.5 50.0 1.0 Water hardness conversion chart (Remove for double machine) Chlorine Less than 0.5ppm Langelier Saturation Index -1.5 to 1.0 TDS 50 to 500 Hardness 90-140ppm pH 6.5 to 8.5 Alkalinity 20 to 140ppm Iron Less than 0.3ppm AUTOMATIC COFFEE MACHINE MAsTRENA sKU# 011011301 EMEA (230V / 25A) Equip_12694_Doc1 5/21/2018 7© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs Dimensions: 528.6 x 603.4 x 635.7mm (WxDxH) 20.8’’ x 23.8’’ x 25’’ Weight net: approx. 171 lbs. / 78 kg (empty) Requirements: Water: The unit requires a 3/8“ compression water connection. Dynamic pressure 1-5 bar / 15-75 psi. El. equipment: 400V / 50/60Hz / 3PNE Power: 8100 W (Powermanagement OFF) Current: 15.0 A Power cord: CE 5 x 2.5mm2 603,4mm 23,8" 528,6mm20,8"418mm16,5"77mm 3,0" 325mm 12,8"635,7mm25,0" Waterhardness German French Englisch Ppm Mval/l 1° dGH 1.0 1.79 1.25 17.8 0.357 1° fTH 0.56 1.0 0.7 10.0 0.2 1° e 0.8 1.43 1.0 14.3 0.286 1° ppm 0.056 0.1 0.07 1.0 0.02 1 mval/l 2.8 5.0 3.5 50.0 1.0 Water hardness conversion chart (Remove for double machine) Chlorine Less than 0.5ppm Langelier Saturation Index -1.5 to 1.0 TDS 50 to 500 Hardness 90-140ppm pH 6.5 to 8.5 Alkalinity 20 to 140ppm Iron Less than 0.3ppm AUTOMATIC COFFEE MACHINE MAsTRENA sKU# 011011303 EMEA (400V / 15A) Equip_12694_Doc1 5/21/2018 8© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs Dimensions: 528.6 x 603.4 x 635.7mm (WxDxH) 20.8’’ x 23.8’’ x 25’’ Weight net: approx. 171 lbs. / 78 kg (empty) Requirements: Water: The unit requires a 3/8“ compression water connection. Dynamic pressure 1-5 bar / 15-75 psi. El. equipment: 220V / 50/60Hz / 2PE Power: 5600 W Current: 25.0 A Power cord: CE 3 x 4mm2 603,4mm 23,8" 528,6mm20,8"418mm16,5"77mm 3,0" 325mm 12,8"635,7mm25,0" Waterhardness German French Englisch Ppm Mval/l 1° dGH 1.0 1.79 1.25 17.8 0.357 1° fTH 0.56 1.0 0.7 10.0 0.2 1° e 0.8 1.43 1.0 14.3 0.286 1° ppm 0.056 0.1 0.07 1.0 0.02 1 mval/l 2.8 5.0 3.5 50.0 1.0 Water hardness conversion chart (Remove for double machine) Chlorine Less than 0.5ppm Langelier Saturation Index -1.5 to 1.0 TDS 50 to 500 Hardness 90-140ppm pH 6.5 to 8.5 Alkalinity 20 to 140ppm Iron Less than 0.3ppm AUTOMATIC COFFEE MACHINE MAsTRENA sKU# 011011304 CHINA ONLy (220V / 25A) Equip_12694_Doc1 5/21/2018 9© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs Dimensions: 528.6 x 603.4 x 635.7mm (WxDxH) 20.8’’ x 23.8’’ x 25’’ Weight net: approx. 171 lbs. / 78 kg (empty) Requirements: Water: The unit requires a 3/8“ compression water connection. Dynamic pressure 1-5 bar / 15-75 psi. El. equipment: 380V / 50/60Hz / 3PNE Power: 8100 W (Powermanagement OFF) Current: 15.0 A Power cord: CE 5 x 2.5mm2 603,4mm 23,8" 528,6mm20,8"418mm16,5"77mm 3,0" 325mm 12,8"635,7mm25,0" Waterhardness German French Englisch Ppm Mval/l 1° dGH 1.0 1.79 1.25 17.8 0.357 1° fTH 0.56 1.0 0.7 10.0 0.2 1° e 0.8 1.43 1.0 14.3 0.286 1° ppm 0.056 0.1 0.07 1.0 0.02 1 mval/l 2.8 5.0 3.5 50.0 1.0 Water hardness conversion chart (Remove for double machine) Chlorine Less than 0.5ppm Langelier Saturation Index -1.5 to 1.0 TDS 50 to 500 Hardness 90-140ppm pH 6.5 to 8.5 Alkalinity 20 to 140ppm Iron Less than 0.3ppm AUTOMATIC COFFEE MACHINE MAsTRENA sKU# 011011306 CHINA ONLy (380V / 15A) Equip_12694_Doc1 5/21/2018 10© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs AUTOMATIC COFFEE MACHINE MAsTRENA sKU# 011011307 JAPAN ONLy (200V / 30A) Dimensions: 528.6 x 603.4 x 635.7mm (WxDxH) 20.8’’ x 23.8’’ x 25’’ Weight net: approx. 171 lbs. / 78 kg (empty) Requirements: Water: The unit requires a 3/8“ compression water connection. Dynamic pressure 1-5 bar / 15-75 psi. El. equipment: 200V / 50/60Hz / 2PE Power: 5800 W Current: 30.0 A Power cord: US 3 x AWG 8 603,4mm 23,8" 528,6mm20,8"418mm16,5"77mm 3,0" 325mm 12,8"635,7mm25,0" Waterhardness German French Englisch Ppm Mval/l 1° dGH 1.0 1.79 1.25 17.8 0.357 1° fTH 0.56 1.0 0.7 10.0 0.2 1° e 0.8 1.43 1.0 14.3 0.286 1° ppm 0.056 0.1 0.07 1.0 0.02 1 mval/l 2.8 5.0 3.5 50.0 1.0 Water hardness conversion chart (Remove for double machine) Chlorine Less than 0.5ppm Langelier Saturation Index -1.5 to 1.0 TDS 50 to 500 Hardness 90-140ppm pH 6.5 to 8.5 Alkalinity 20 to 140ppm Iron Less than 0.3ppm Equip_12694_Doc1 5/21/2018 11© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs Waterhardness German French Englisch Ppm Mval/l 1° dGH 1.0 1.79 1.25 17.8 0.357 1° fTH 0.56 1.0 0.7 10.0 0.2 1° e 0.8 1.43 1.0 14.3 0.286 1° ppm 0.056 0.1 0.07 1.0 0.02 1 mval/l 2.8 5.0 3.5 50.0 1.0 WATER PUMP 1/2 CUT sHEET Water hardness conversion chart Requirements:Water: The pump requires a 9/16 UNEF compression water connection. Dynamic pressure 1-5 bar / 15-75 psi. El. equipment: 230V / 50/60Hz / PNEPower: 90 WCurrent: 0.9 A, 5mF, 450VL CL B A3234HGFEDCB 4 3 2 ABCDEFGH1A 1 Ce dessin est confidentiel et la propriété exclusive deThermoplan SA et ne peut-être reproduit, modifié outransmis sous quelque forme que se soit, sans l'autorisationécrite de Thermoplan SA.Diese Zeichnung ist vertraulich und Eigentum derThermoplan AG und darf ohne schriftliche Genehmigung derThermoplan AG weder vervielfältigt, geändert oder inirgendeiner Form weitergegeben werden.This drawing is confidential and belongs exclusively toThermoplan AG. It is forbidden to reproduce, to modify ortransfer in any form without the Thermoplan AG writtenagreement.72.24.10 PDF Date :2007-10-04 1:2 NameDate -TPA001 Quality control Weight Released Checked Drawn Creation Wasserpumpe V901 USA kpl. Rue du PrieuréCH-1955 St-Pierre-de-ClagesTél. 41 (0)27 305 66 00Fax 41 (0)27 305 66 01 12.065 kg -- B.In-Albon2008-02-04 dpittet2008-02-04 P.Mayoraz2008-02-04 Pompe à eau externe V901 USA cpl. 72.24.10 277x213x188 Overall dimensions - 2 / 2722410.dftFile name : Material : DescriptionRev.NameDate Art. N°:Scale : Page/389/16-24 UNEF (1,5“)133.7(5,3“)38(1,5“)48,2(1,9“)158(6,2“)119.3(4,7“) 132(5,2“) 150(5,9“) 257 (10,1“) 288.6 (11,4“) 92.5(3,6“) 103 (4,1“)operating pressure 9 barsA3234HGFEDCB 4 3 2 ABCDEFGH1A 1 Ce dessin est confidentiel et la propriété exclusive deThermoplan SA et ne peut-être reproduit, modifié outransmis sous quelque forme que se soit, sans l'autorisationécrite de Thermoplan SA.Diese Zeichnung ist vertraulich und Eigentum derThermoplan AG und darf ohne schriftliche Genehmigung derThermoplan AG weder vervielfältigt, geändert oder inirgendeiner Form weitergegeben werden.This drawing is confidential and belongs exclusively toThermoplan AG. It is forbidden to reproduce, to modify ortransfer in any form without the Thermoplan AG writtenagreement.72.24.10 PDF Date :2007-10-04 1:2 NameDate -TPA001 Quality control Weight Released Checked Drawn Creation Wasserpumpe V901 USA kpl. Rue du PrieuréCH-1955 St-Pierre-de-ClagesTél. 41 (0)27 305 66 00 Fax 41 (0)27 305 66 01 12.065 kg -- B.In-Albon2008-02-04 dpittet2008-02-04 P.Mayoraz2008-02-04 Pompe à eau externe V901 USA cpl. 72.24.10 277x213x188 Overall dimensions - 2 / 2722410.dftFile name : Material : DescriptionRev.NameDate Art. N°:Scale : Page/389/16-24 UNEF (1,5“)133.7(5,3“)38(1,5“)48,2(1,9“)158(6,2“)119.3(4,7“) 132 (5,2“) 150(5,9“) 257(10,1“) 288.6(11,4“) 92.5(3,6“) 103 (4,1“)operating pressure 9 barsA3234HGFEDCB 4 3 2 ABCDEFGH1A 1 Ce dessin est confidentiel et la propriété exclusive deThermoplan SA et ne peut-être reproduit, modifié outransmis sous quelque forme que se soit, sans l'autorisationécrite de Thermoplan SA.Diese Zeichnung ist vertraulich und Eigentum derThermoplan AG und darf ohne schriftliche Genehmigung derThermoplan AG weder vervielfältigt, geändert oder inirgendeiner Form weitergegeben werden.This drawing is confidential and belongs exclusively toThermoplan AG. It is forbidden to reproduce, to modify ortransfer in any form without the Thermoplan AG writtenagreement.72.24.10 PDF Date :2007-10-04 1:2 NameDate -TPA001 Quality control Weight Released Checked Drawn Creation Wasserpumpe V901 USA kpl. Rue du PrieuréCH-1955 St-Pierre-de-Clages Tél. 41 (0)27 305 66 00 Fax 41 (0)27 305 66 01 12.065 kg -- B.In-Albon2008-02-04 dpittet2008-02-04 P.Mayoraz2008-02-04 Pompe à eau externe V901 USA cpl. 72.24.10 277x213x188 Overall dimensions - 2 / 2722410.dftFile name : Material : DescriptionRev.NameDate Art. N°:Scale : Page/389/16-24 UNEF (1,5“)133.7(5,3“)38(1,5“)48,2(1,9“)158(6,2“)119.3 (4,7“) 132(5,2“) 150(5,9“) 257 (10,1“) 288.6(11,4“) 92.5(3,6“) 103 (4,1“)operating pressure 9 barsø 9,5 (0.37“) Chlorine Less than 0.5ppm Langelier Saturation Index -1.5 to 1.0 TDS 50 to 500 Hardness 90-140ppm pH 6.5 to 8.5 Alkalinity 20 to 140ppm Iron Less than 0.3ppm Equip_12694_Doc1 5/21/2018 12© 2010 by Thermoplan AG, 2010-10-08 Subject to change CUT sHEETs Dimensions: 213 x 289 x 166.5mm (WxDxH) 8.39’’ x 11.38’’ x 6.56’’ Weight net: approx. 15.4 lbs. / 7 kg (empty) WATER PUMP 2/2 CUT sHEET Water connection from line 9/16“UNEF (1-5bar / 15-75psi) El. connection Machine-Pump Water connection Pump-Machine 9/16“UNEF (9bar / 130 psi)H8G F E D C B A 8 7 6 5 4 3 2 1 A B C D E F G H1234576 A2 Ce dessin est confidentiel et la propriété exclusive deThermoplan SA et ne peut-être reproduit, modifié outransmis sous quelque forme que se soit, sans l'autorisationécrite de Thermoplan SA.Diese Zeichnung ist vertraulich und Eigentum derThermoplan AG und darf ohne schriftliche Genehmigung derThermoplan AG weder vervielfältigt, geändert oder inirgendeiner Form weitergegeben werden.This drawing is confidential and belongs exclusively toThermoplan AG. It is forbidden to reproduce, to modify ortransfer in any form without the Thermoplan AG writtenagreement.1 / 2 Volume NameDate Quality control Weight PDF Checked Drawn Creation Thermoplan AGCH-6353 Weggis Overall dimensions File name : Scale: Page Pompe à eau externe V901 USA cpl. Wasserpumpe V901 USA kpl. Old Nr.: 0.0 8200.0 108.554 A P. Mayoraz D. Pittet B. In-Albon B. In-Albon 1:1 150x158x289 / Thermoplan AG, Creative CenterCH-1955 St-Pierre-de-Clages General tolerances:ISO 2768-fH TPA 001 -722410.dft 72.24.10 2007-10-04 2007-10-04 2008-02-01 2008-02-01 Rev. pro pro A B C Description Gehause 1 Stuck pli inferieur UL Anpassung Date 2008-01-29 2008-02-01 2008-02-04 Name IAB IAB IAB Pos.Qty.Bezeichnung / Normbez. Werkstoff Désignation / Handelsname Werkstoff Referenz Normteil / Standardteil Ref.Old Ref. 10 1 Gerätstecker Prise appareil 250VAC / 15A / 2m 102.489 20.33.00 20 2 Anschlussnippel MM 3/8-9/16-24 U Raccord MM 3/8 - 9/16-24 UNEF 108.577 71.20.0572 30 2 "Dichtung 3/8"" Bi-Material"Joint bi-matière 3/8 EPDM 101.384 71.23.40 40 1 Kabelbaum Wasserpumpe V901 Torche câblage pompe ext. V901 108.473 71.37.64 50 4 Puffer zu Wasserpumpe Elément de fixation M5 FLEX-LOC 105.090 71.40.15 60 1 Kleber Wasseranschluss CU+SU "Etiquette ""... comply with plu 103.780 71.44.42 70 1 Kleber water pump mounting "Etiquette ""water pump mounting 103.781 71.44.92 80 1 Befestigungsbride SP-09 Bride attache cable SP-09 100.708 71.45.91 90 1 Feder zu Pumpenstecker CU-SU Ressort fiche pompe CU - SU 101.910 71.46.76 100 1 Linsen-Kombischrauben Phil H M04 Vis combi. tete bombee Phil H 04 Bossard: BN01720 M4x8 104.016 71.50.15 110 1 Wasserpumpe Inox mit Motor Pompe à eau avec moteur 108.046 72.21.25 120 1 Gehäuse Pumpe komplet Boîtier pompe externe complet 115.075 130 4 Kabeltülle O10 Passe-fil o6/9/14 ep.2 103.253 71.41.82 140 1 Rippenscheibe M04 Rondelle elastique nervuree M04 Bossard: BN00791 M4 105.413 71.50.24 150 4 Senkschraube Phil H M05x16 Vis a tete fraisee Phil H M05x16 Bossard: BN00388 M5x16 106.401 71.54.87 160 1 Sicherungsmutter M04 Ecrou autofreine forme basse M04 Bossard: BN00161 M4 106.516 04.04.00 Achtung: Einbauposition!31,6 288,6 38,5115133,7196 257 40 103 40 103 92,5 38132150A A 160 120 10 20 30 40 50 130 60 70 80 90 100 140 150 110 1589/16 UNEF B BSECTION B-B12 Equip_12694_Doc1 5/21/2018 File:File:File:File:SB-M 226-SB-M 226-SB-M 226-SB-M 226- FFFF Date:Date:Date:Date: Verismo:Verismo801Verismo801Verismo801Verismo801 Verismo801CVerismo801CVerismo801CVerismo801C Verismo801SVerismo801SVerismo801SVerismo801S Mastrena:xxxx Mastrena Mastrena Mastrena Mastrena V901 (SBC)V901 (SBC)V901 (SBC)V901 (SBC) Initial InformationInitial InformationInitial InformationInitial Information xxxx Final BulletinFinal BulletinFinal BulletinFinal Bulletin ChangementChangementChangementChangement xxxx NewNewNewNew xxxx InfoInfoInfoInfo Art. No.: What: no specific action by the service organization required. Approved for:xxxx US MarketUS MarketUS MarketUS Market xxxx International MarketInternational MarketInternational MarketInternational Market Approved by:Date:19.10.2010 Name: pcamera Approved by:Date:19.10.2010 Name: akatzenhofer Change Management: (Initial) Verismo: SB-V 00X-I Mastrena: SB-M 00X-I General: SB-G 00X-I Change Management: (Final) Verismo: SB-V 00X-F Mastrena: SB-M 00X-F General: SB-G 00X-FDescriptionDescriptionDescriptionDescriptionThermoplanThermoplanThermoplanThermoplanApprovalApprovalApprovalApprovalStarbucksStarbucksStarbucksStarbucks Implemented in production after S/N: UL40-049512 (2010-10-19) UL40-049512 (2010-10-19) UL40-049512 (2010-10-19) UL40-049512 (2010-10-19) New articles are shown in Mastrena manual section11, page 6&7 New SKU's are issued for the standard units Change to unique enclosure design. Back panel carries the Starbucks badge and the Mastrena Logo. Left side panel has brushed chrome look (refer to SBM-225) and right panel remains on copper look (view from back). For installation will be two of these standard units used instead of a Badge and Logo configuration. standard enclosure design - fusion Logo&Badgestandard enclosure design - fusion Logo&Badgestandard enclosure design - fusion Logo&Badgestandard enclosure design - fusion Logo&Badge Change Management STARBUCKSChange Management STARBUCKSChange Management STARBUCKSChange Management STARBUCKS 2010-10-212010-10-212010-10-212010-10-21 several - refer to Mastrena manual section 11, page 6/7several - refer to Mastrena manual section 11, page 6/7several - refer to Mastrena manual section 11, page 6/7several - refer to Mastrena manual section 11, page 6/7TypeTypeTypeTypeHeaderHeaderHeaderHeader ActionActionActionActionNoticeNoticeNoticeNoticeFORM 10043-1 SBUX 1/1 Equip_12694_Doc1 5/21/2018 Item # _____________________________________ Quantity ___________________________________ C.S.I. Section 11400 F40336 – LXeR and LXePR Hot and Cold Page 1 of 4 LXeR and LXePR HOT AND COLD701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • www.hobartcorp.com LXeR and LXePRHOT AND COLDSTANDARD FEATURES ■Racks per hour Light Normal Heavy LXeR 30 24 13 LXePR 38 29 14 ■.62 gallons of water per rack – LXeR 1.14 gallons of water per rack – LXePR ■Hot water or chemical sanitation units available ■Steam Elimination and Energy Recovery (LXeR model only) ■PuriRinse cycle (Potable water rinse to remove chemical residue) (LXePR model only) ■NSF Certified pot and pan cycle on heavy cycle (LXeR model only) ■Low chemical alert indicators ■Sense-A-Temp™ booster heater capable of 70 rise, provided on LXeR models ■Chemical pump “auto-prime” ■Advanced Service diagnostics ■Clogged wash arm sensing ■Custom cycle selection – light, normal, heavy ■Automated delime cycle – includes booster deliming ■Deep drawn stainless steel tank ■Microcomputer, top mounted controls with advanced digital cycle/temperature display ■Revolving upper and lower anti-clogging wash arms ■Snap in revolving upper and lower rinse arms ■Removable stainless steel scrap screen ■Corrosion resistant pump ■Energy Saver mode ■Automatic pumped drain ■17" door opening ■Dirty water indicator ■Automatic fill ■Detergent, rinse aid and delime pumps standard (plus sanitizer pump on chemical machine) ■Electric tank heat ■Two dishracks – one peg and one combination type ■Customizable “advansys” button to select favorites function ■Auto clean cycle washes down inside of machine at shutdown MODELS ❑LXeR – Energy Recovery ❑LXePR – PuriRinse STANDARD VOLTAGES ❑120/208-240(3W)/60/1 (LXeR model only) ❑120/60/1 (LXePR model only) OPTIONS AT EXTRA COST ❑208-240(2W)/60/1 (LXeR model only) ❑208-240/60/3 (LXeR model only) ACCESSORIES ❑Power cord kits ❑Stainless steel base with 6" legs ❑17" stainless steel stand with storage ❑External caster kit ❑DWT-LXe drain water tempering kit Specifications, Details and Dimensions on Back. 15186 15186 5/21/2018 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • www.hobartcorp.com Page 2 of 4 F40336 – LXeR and LXePR Hot and Cold LXeR HOT 15186 5/21/2018 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • www.hobartcorp.com Page 4 of 4 F40336 – LXeR and LXePR Hot and Cold As continued product improvement is a policy of Hobart, specifications are subject to change without notice. LXeR and LXePR HOT AND COLD F40336 (REV. 03/13) LITHO IN U.S.A. (H-01) SPECIFICATIONS DESIGN: Front opening, equipped for installation in either free- standing or undercounter-type operations. CONSTRUCTION: 300 series stainless steel tank, door and top panel. PUMP: Centrifugal-type, integral with motor, horizontally mounted. Pump capacity 38 gpm. MOTOR: Single phase, furnished for all electrical specifications. Factory sealed lubrication. Inherent overload protection with auto reset. WASH AND RINSE CYCLE: Complete automatic type, controlled by solid-state electronics. Cycle may be interrupted any time by opening door. Cycle continues when door is closed. • Initial cycle fills wash tank, to be recirculated each wash cycle. Some wash water is drained off before rinse cycle. Rinse cycle refreshes wash water and tank heat. RINSE PUMP: Powered by a single phase motor, the rinse pump is made of high strength engineered composite material. BLOWER: The blower is a 60mm x 300mm tangential wheel powered by a 2-pole single phase motor for quiet and reliable operation, LXeR only. CONDENSER COIL: The condensing system uses a tube and fin coil constructed of copper and corrosion resistant aluminum. The condenser coil allows for energy recovery from waste heat in the moisture laden air that would normally escape into the environment after a dishwashing cycle, LXeR only. RINSE AND SANITATION: • LXeR: Sanitation is accomplished by means of a built-in booster heater designed to raise temperature of water to a minimum of 180°F from an incoming water temperature of 55°F. • LXePR: Sanitation is accomplished by injection of proper amount of sodium hypochlorite solution (liquid bleach) into final rinse water to achieve a minimum of 50PPM sanitizing solution. Injection of sodium hypochlorite is accomplished by a built-in sanitizing chemical pump. Minimum required hot water temperature is 120°F. – Potable water rinse to remove chemical residue. – To be used with sanitizer approved for use with post sanitizing rinse • CHECK SANITIZER CONCENTRATION: PuriRinse must be off (hold Wash button for 5 seconds). Verify that there is suffi- cient chemical supply. Run cycle and use test trips on wetted surface of glasses after cycle is complete. If concentration is below minimum required, contact your local Hobart Service office. ENERGY RECOVERY: Heat energy is recovered from the con- densation of vapors in the chamber at the end of each cycle. This pre-heats the water for the next rinse cycle from 55°F up to 140°F. PUMPED DRAIN: Machine automatically drains water through a built-in pump. Maximum 38" drain height permitted. ELECTRIC BOOSTER HEATER: 4.9 KW electric booster with Sense-A-Temp™ technology adequately sized to raise 55°F inlet water to 180°F, with the aid of the energy recovery system. RACKING: Machines accommodate racks from 10" x 20" to 20" x 20". Also accepts 16" x 18" cafeteria trays. NOTE: Certain materials, including silver, aluminum and pewter are attacked by Sodium Hypochlorite solution in the chemical sanitizing mode of operation. SPECIFICATIONS: Listed by Underwriters Laboratories Inc. and NSF International. MACHINE RATINGS LXePR LXeR Light Normal Heavy Light Normal Heavy Racks per Hour Rate 38 29 14 30 24 13 Dishes per Hour (25 per Rack Avg.)950 725 350 750 600 325 Glasses per Hour (36 per Rack Avg.)1368 1044 504 1080 864 468 Controls Microcomputer Tank Capacity - Gallons 2.9 Overall Dimensions - H x W x D 321⁄2" x 2315⁄16" x 259⁄16"321⁄2" x 2315⁄16" x 2613⁄16" Cycle Time - Seconds 94 124 254 120 146 275 Tank Heat 1.8 KW Electric Booster Heater N/A 4.9 KW Water Usage Per Rack - Gallons 1.14 .62 Drain Design Pumped Door Opening Height 17" Detergent Pump Standard Rinse-Aid Pump Standard Delime Pump Standard Sanitizer Pump Standard N/A Chemical Prime (auto prime)Standard Peak Drain Flow - GPM 4.0 Advanced Service Diagnostics Standard Advanced Cleaning Cycle Standard 70°Rise Sense-A-Temp™ Booster Heater N/A Standard Incoming Water Temperature Required (minimum)120°55° 15186 5/21/2018 Parker Hannifin Corporation Gas Separation and Filtration Division 4087 Walden Ave. Lancaster, NY 716-686-6400 www.parker.com/gsf 6 2 Description The Parker Nitrogen Generator is designed to provide a constant supply of nitrogen gas, at a pre-selected purity, flow, and pressure, as specified in section 2.1 below. The system uses proven Pressure Swing Adsorption (PSA) technology with a Carbon Molecular Sieve (CMS) to separate nitrogen (N2) from the atmosphere and store it at a high purity level. This user guide contains all of the information necessary for the correct use of the Parker Nitrogen Generator range. Should you have any questions regarding the safe and correct installation, operation or maintenance of the generator, contact the supplier before proceeding. Performance Specifications Model Units CN-6JA-100 CN-6NA CN-6WD CN-6CHN Outlet flow SCFH (l/min) 6 (2.8) 6 (2.8) 6 (2.8) 6 (2.8) Maximum outlet pressure psig (barg) [kPa] 85 (5.9) [586] 85 (5.9) [586] 85 (5.9) [586] 85 (5.9) [586] Mechanical connections Nitrogen Outlet CPC 1800 (1/4” hose barb valve inline coupling) Electrical Specifications Connection Type IEC320 IEC320 IEC320 IEC320 Supply Voltage Range *VAC 100V 1 phase + PE 50/60Hz 120V 1 phase + PE 60Hz 230V 1 phase + PE 50/60Hz 230V 1 phase + PE 50/60Hz Supply Voltage Fluctuation ± 10%± 10%± 10%± 10% Current A 6 6 3 3 Fuse A 10 ((T), 10A, 250v) 10 ((T), 10A, 250v) 5 ((T), 5A, 250v) 5 ((T), 5A, 250v) Cordset Included Included *Included 2.1 Technical Specification This specification is valid when the equipment is located, installed, operated, and maintained as specified within this user guide. *Ordered seperately (see chart on the bottom of page 7). 18076 5/21/2018 Parker Hannifin Corporation Gas Separation and Filtration Division 4087 Walden Ave. Lancaster, NY 716-686-6400 www.parker.com/gsf 7 2 Description Regulatory Certifications Model CN-6NA CN-6WD CN-6JA-100 CN-6CHN UL Certification Standard UL61010-1 3rd Edition UL61010-2-201 1st Edition UL61010-1 3rd Edition UL61010-2-201 1st Edition UL61010-1 3rd Edition UL61010-2-201 1st Edition UL61010-1 3rd Edition UL61010-2-201 1st Edition IEC Certification Standard IEC61010-1:2010, MOD IEC61010-1:2010, MOD IEC61010-1:2010, MOD IEC61010-1:2010, MOD CSA Certification Standard CAN/CSA C22.2 No. 61010-1-12 CAN/CSA-IEC 61010-2- 201:14 CAN/CSA C22.2 No. 61010-1-12 CAN/CSA-IEC 61010-2- 201:14 CAN/CSA C22.2 No. 61010-1-12 CAN/CSA-IEC 61010-2- 201:14 CAN/CSA C22.2 No. 61010- 1-12 CAN/CSA-IEC 61010-2- 201:14 CB Certification DK-65436-UL DK-65436-UL DK-65436-UL DK-65436-UL S. Korean EMC Test -EMI7053.17 -- EMC Standard FCC Part 15 Subpart B EN61326-1: 2013 CISPR-11: 2015, Class B EN61326-1: 2013 CISPR-11: 2015, Class B EN61326-1: 2013 CISPR-11: 2015, Class B NSF Certification Standard NSF/ANSI Standard 18 NSF/ANSI Standard 18 NSF/ANSI Standard 18 NSF/ANSI Standard 18 Environmental Specifications Ambient Temperature oF (oC) 36 – 95 (2 – 35) Maximum Humidity (80% MAX ≤ 31°C) IP Rating IP20 Pollution Degree 2 Installation Category II Altitude ft (m) < 6562 (< 2000) Noise dB(A)<65 Weight Shipping weight (single unit)Lbs (kgs)171 (78) Product Lbs (kgs)107 (49) *Ordered Seperately Country/Territory Electric Cordset (with Plug) Australia 13412AU Brunei 13412UK Cambodia 13412UK Europe 13412EU Hong Kong 13412UK India 13412IND Indonesia 13412EU Malaysia 13412UK New Zealand 13412AU Philippines 13412UK Singapore 13412UK South Korea EW8003 Thailand EW8005 UK 13412UK Vietnam 13412EU 5/21/2018 Parker Hannifin Corporation Gas Separation and Filtration Division 4087 Walden Ave. Lancaster, NY 716-686-6400 www.parker.com/gsf 8 2.1.1 Dimensions 2.2 Unpacking the equipment This system is heavy. Be careful in removing the system from the packaging set. Remove the equipment from its packaging. Check system was not damaged in transit. Verify that the installation kit is included with your equipment. Installation kit includes: • Wall anchor bracket• ¼ turn fastener• CPC female NSF fitting• Decorative screw caps for anchor bracket and cap removal tool• Operator Quick Start guide Figure 1: System Features and Dimensions If any items are missing or damaged, please contact your Parker representative. Description P/N Qty Installation Kit B06-0619 1 5/21/2018 DATE: PROJECT: ITEM NO: Product Specifications - Starbucks Corporation Lengths include end panels 54-1/4"L x 35"D x 52"H□SBZ5452DR 66-1/4"L x 35"D x 52"H□SBZ6652DR Combination Non-Refrigerated Service Above Refrigerated Self-Service Case STANDARD FEATURES ■Breeze™ w/EnergyWise s/c refrigeration (Hot gas condensate) ■4''H front glass shield ■Digital controller ■Foam-in-place insulated tub ■Glass upper display area. ■Integrated average product temperature of 40°F or less ■LED top light in lower display ■Rear electrical access Features Standard Options EXTERIOR COLOR □Black Gray INTERIOR COLOR □Black Gray END PANEL LEFT □Full end panel w/mirror interior in lower display END PANEL RIGHT □Full end panel w/mirror interior in lower display FRONT GLASS □Tempered (service) REAR WRAPPING BOARD □Rear wrapping board, black Sanalite® TOE KICK □Black Gray UPPER REAR □Acrylic rear sliding doors w/o lock ELECTRICAL CONNECT □Leads REFRIGERATION □Breeze™ w/EnergyWise s/c refrigeration (Hot gas condensate) THERMOMETER □Spirit filled thermometer 3/30/2017Revised 20480348 Note: Information is subject to change at any time. Visit www.structuralconcepts.com for the most current specs. 888 E. Porter Rd. Muskegon, MI 49441 Ph. 231-798-8888 Fx. 231-798-4960 www.structuralconcepts.com DID 16238 - MODEL SBZ5452DR DID 16239 - MODEL SBZ6652DR 16239 5/21/2018 Product Specifications Intended Environment:Type I - Designed to operate in ambient conditions of 75°F with 55% relative humidity unless noted otherwise in system information below. Warmest Avg Prod Temp ° F Intended Product To Be Displayed Zone 1 Packaged refrigerated products 40 40 Unpackaged refrigerated products2 Model Technical Specifications Model L1"L2"WattsFreqPhsSystem Circuit Volts Wires BTUHNEMA Plug Est Wt Amps ***SSTL" 99054.25N/ASBZ5452DR .00 Self-Contained Circuit #1 N/AN/ALeads Single2+G6.81601208-240 997 1,15066.25N/ASBZ6652DR .00 Self-Contained Circuit #1 N/AN/ALeads Single2+G6.83601208-240 1,010 Regulatory Approvals: All Models Accordance with AHRI Std 1200 ETL Listed to UL 471 ETL Listed to CAN/CSA 22.2 No. 120 NSF Std 7 Listed *** Does not include electric defrost on freezer models.Important Notes: 1) Units are supplied with levelers. They must be adjusted during installation to ensure the unit is level and plumb. Dimensions reflect levelers extended 1 5/8''. 2) Refer to serial label for refrigerant type. Cases built before March 2017 contain R-404a, and case built after contain R-134a. 888 E. Porter Rd. Muskegon, MI 49441 Ph. 231-798-8888 Fx. 231-798-4960 www.structuralconcepts.com 3/30/2017Revised Note: Information is subject to change at any time. Visit www.structuralconcepts.com for the most current specs. 20480348 DID 16238 - MODEL SBZ5452DR DID 16239 - MODEL SBZ6652DR 5/21/2018 Technical Information - Oasis - Combination Non-Refrigerated Service Above Refrigerated Self-Service Case Page 1 of 2 DIMENSIONS / SHIPPING Model L" L1" L2" Est Wt (lbs) N/A 54.250 0.000 990SBZ5452DR N/A 66.250 0.000 1,150SBZ6652DR ELECTRICAL Model System Circuit Volts Ph Frq Rated Load Amps Watts Wires NEMA Plug Amps Lights Amps Fans Amps Anti- Sweats Amps Misc/Refrig/ Heat Min Cir Amps Max OCP Amps SBZ5452DR Circuit #1 208-240 997 2+G Leads Single1606.81Self-Contained 15 15 0.36 6.060.090.66 SBZ6652DR Circuit #1 208-240 1,010 2+G Leads Single1606.83Self-Contained 15 15 0.36 3.902.270.66 REFRIGERATION REMOTE REFRIGERATION GLYCOL REFRIGERATION Temp (°F) Concent (%) Pressure Drop (psi)GPM Defrost Duration (Mins) Defrost Interval (Hrs)BTUHSST (°F) Model Zone Section EnvtSystem SBZ5452DR Type IISelf-Contained-R134ARefrigeratorAll N/A N/A N/A N/AN/AN/A N/A N/A N/A SBZ6652DR Type IISelf-Contained-R134ARefrigeratorAll N/A N/A N/A N/AN/AN/A N/A N/A N/A IMPORTANT NOTES 1) Units are supplied with levelers. They must be adjusted during installation to ensure the unit is level and plumb. Dimensions reflect levelers extended 1 5/8''. 2)Refer to serial label for refrigerant type. Cases built before March 2017 contain R-404a, and case built after contain R-134a. INTENDED ENVIRONMENT Type I - Designed to operate in ambient conditions of 75°F with 55% relative humidity unless noted otherwise under Envt above. WARMEST AVERAGE PRODUCT TEMP & INTENDED USE OF ZONES Intended UseTemp (°F)Zone Packaged refrigerated products 40 1 2 Unpackaged refrigerated products 40 REGULATORY All Models Accordance with AHRI Std 1200 ETL Listed to UL 471 ETL Listed to CAN/CSA 22.2 No. 120 NSF Std 7 Listed 888 E. Porter Rd. Muskegon, MI 49441 231-798-8888 Revised 3/30/2017 20480348 Foodservice DID 16238 - MODEL SBZ5452DR DID 16239 - MODEL SBZ6652DR 5/21/2018 Technical Information - Oasis - Combination Non-Refrigerated Service Above Refrigerated Self-Service Case Page 2 of 2 888 E. Porter Rd. Muskegon, MI 49441 231-798-8888 Revised 3/30/2017 20480348 Foodservice DID 16238 - MODEL SBZ5452DR DID 16239 - MODEL SBZ6652DR 5/21/2018 RECOMMENDED PARTS LIST ZEPHYR MODELS SBZ6652DR and SBZ5452DR DESCRIPTION SCC PART #QTY MAGNETIC FILTER 83644 1 MAIN POWER SWITCH 5-5000 1 LIGHT SWITCH 75785 1 CONTACTOR -- 30A 220V 20-04881 1 COND FAN MOTOR 77422 2 COMPRESSOR #NT6217GKV for R-404a cases 20-13399 1 COMPRESSOR #FFU160HAX for R-134a cases 20-69989 1 TXV VALVE #EFSE-1/2-CP115 for R-404a cases 20-13510 1 TXV VALVE #EFJE-1/4-JCP for R-134A cases 72645 1 EVAP FAN MOTOR 5-9055 4 WICKING MATERIAL 83358 2 REAR DOOR SEAL KIT 20-75369 1 THERMOMETER 20-09795 1 MODEL SBZ6652DR ONLY 66 1/4" L REAR ACRYLIC DOOR - RIGHT HAND 20-52858 1 REAR ACRYLIC DOOR - LEFT HAND 20-52859 1 LED BULB 42K 20-75466 1 GLASS TOP ASSEMBLY REPLACEMENT KIT with DOORS 20-61427 1 MODEL SBZ5452DR ONLY 54 1/4"L REAR ACRYLIC DOOR - RIGHT HAND 20-59558RH 1 REAR ACRYLIC DOOR - LEFT HAND 20-59558LH 1 LED BULB 42K 20-75464 1 GLASS TOP ASSEMBLY REPLACEMENT KIT with DOORS 20-63997 1 DID 16238 - MODEL SBZ5452DR DID 16239 - MODEL SBZ6652DR 5/21/2018 Features • Application storage capacity from 242 lbs (110 kg) to 1846 lbs (837 kg). • Ultra-low profile — 28" (711 mm) to 67" (1702 mm) tall. • Multiple bin tops provide an easy solution for mounting ice makers on different sized bins. • Each polyethelyne bin liner is insulated with foam for maximum ice preservation — 1.5" to 3" (38 mm to 76 mm) of insulation. • Perfect-fit seal for improved ice preservation. • Rugged, fingerprint-proof door. • Built-in ice scoop holders on featured models. • Sturdy leg design — 6" (152 mm) adjustable NSF approved legs — standard. • Stainless exterior. • Corrosion-proof bin liner. Storage BinS StoRAgE BiNSIce. Pure and Simple Ordering and Specification Information — Required Bin Top Bin Model no.app. Storage rating ari Bin Storage lbs (kgs) Bin Weight lbs (kgs) iCe Series™ Cube ice Makers Pearl ice Makers Flake ice Makers 22" (559 mm) wide 30" (762 mm) wide 48" (1219 mm) wide 21" (533 mm) wide 21" (533 mm) wide 42" (1067 mm) wide B25PP 242 (110) 190 (86) 74 (34) KBt19 Not Required n/a KBt19 KBt19 n/a B40PS 344 (156) 270 (123) 120 (54) KBt19 Not Required n/a KBt19 KBt19 n/a B42PS 351 (160) 275 (125) 128 (58)Not Required N/A n/a KBt24 KBt24 n/a B55PS 510 (232) 400 (182) 148 (67) KBt19 Not Required n/a KBt19 KBt19 n/a B70SP 741 (336) 581 (264) 240 (109)included included n/a included included n/a B90SP 1023 (464) 802 (364) 285 (129)included included n/a included included n/a B100 PS 854 (388) 670 (304) 191 (87)Not Available KBt5 Not Required KBt23 KBt23 KBt26 B120SP/SS 1161 (527) 911 (413) 280 (127)included included included included included included B130SP/SS 1457 (661) 1144 (404) 320 (145) included included included included included included B150SP/SS 1471 (669) 891 (404) 310 (141)included included included included included included B170SP/SS 1846 (837) 1110 (503) 370 (168)included included included included included included • = Bin top is included for each cube ice maker — must specify ice maker application when ordering bin. Bin Height includes 6" (423 mm) legs. All bins have polyethylene liners. Equip_10102_Doc1 10102 5/21/2018 rev: 03/11 Part: 3000 11100 e. 45th avenue • Denver, Co 80239 • Phone: 1. 866. PUre. iCe • Fax: 303. 371. 6296 • www.iceomatic.com Ice. Pure and Simple StoRAgE BiNSStorage BinS Dimensions NotES: Approx. Shipping Weight lbs (kg): B100 191 (87 kg) • B120 304 (138 kg) • B130 334 (152 kg) • B150 338 (153 kg) • B170 390 (177 kg) B25 95 (43 kg) • B40 135 (61 kg) • B42 135 (61 kg) • B55 170 (77 kg) • B70 240 (109 kg) • B90 285 (129 kg) Equip_10102_Doc1 5/21/2018 103445/21/2018 5/21/2018 5/21/2018 5/21/2018 Features • Only 30" (762 mm) wide. • Produces up to 1,000 lbs (454 kg) of ice per day. • Harvest Assist provides consistent ice production for the life of the ice maker while reducing energy consumption and increasing capacity. • Pure Ice® exclusively by Ice-O-Matic. Built-in antimicrobial protection for the life of the ice maker inhibits bacteria growth on ice maker surfaces. Ice-O-Matic's optional water filtration system provides protection against unpleasant tastes, odors and scale formation. • Durable, electroless nickel plating on all evaporator plates ensures reliability. • Longest warranty in the industry. Purchase an Ice-O-Matic water filter with your cube ice maker, replace the filter every six months, and the evaporator warranty is extended to 7 years parts and labor (available in the U.S. and Canada only). • Constructed from corrosion-resistant stainless steel and fingerprint-proof plastic. ICE1006/1005/1007 - CubE ICE MakEr ICE1006/1005/1007 CuBE ICE MakErice. Pure and simple ICE1006 On B55 Options & Accessories Ice Machine Model Manifold Inline System replacement System ICE1006 IFQ2 IOMQ (2)n /aICE1005 ICE1007 wAter Filters ice Maker warranty Every Ice-O-Matic ice maker is backed by a warranty that provides both parts and labor coverage. • Three years Parts and Labor. • Five years Parts coverage on the evaporator and compressor. • Seven years Parts and Labor on the evaporator when you purchase an Ice-O-Matic water filter with your cube ice maker and replace the filter every six months (available in the U.S. and Canada only). ice Form CubE Full Cube DiMensiOns W x D x H (in.) 7/8 x 7/8 x 7/8 W x D x H (mm) 22 x 22 x 22 HAlF Cube DiMensiOns W x D x H (in.) 3/8 x 7/8 x 7/8 W x D x H (mm) 10 x 22 x 22 *See Ice-O-Matic Price List for Adapter Kits to combine ice makers with most available ice/beverage dispensers.kits Model No. Capacity Width b25 242 lbs (110 kg) 30 in (762 mm) b40 344 lbs (156 kg) 30 in (762 mm) b42 351 lbs (160 kg) 22 in (559 mm) b55 510 lbs (232 kg) 30 in (762 mm) b70 741 lbs (337 kg) 30 in (762 mm) b90 1023 lbs (465 kg) 30 in (762 mm) b100 854 lbs (388 kg) 48 in (1219 mm) b120 1142 lbs (519 kg) 48 in (1219 mm) b150 1447 lbs (658 kg) 60 in (1524 mm) b170 1807 lbs (821 kg) 60 in (1524 mm) ICE1006 kit not required n /a kit not required kBT 5 Filler kit requiredICE1005 ICE1007 bin Chart Kits for Combining Wider Bins with Smaller Models iCe stOrAge bins 10475 10475 5/21/2018 rev: 02/13 Part: 1011 11100 E. 45th Avenue • Denver, CO 80239 • Phone: 1. 866. PURE. ICE • Fax: 303. 371. 6296 • www.iceomatic.com ice. Pure and simple ICE1006/1005/1007 CuBE ICE MakErICE1006/1005/1007 - CubE ICE MakEr Air Cooled Please note: air-cooled units require 6" (152 mm) clearance for air intake and exhaust. a. Ice maker potable water in, 3/8" FPT. B. Ice maker water out, 3/4" FPT. C. Hole for electrical connections, 7/8". D. Electrical connection junction box. Operating requirements All mODEls Dimensions W x D x H (in.) 30.13 x 24.25 x 26.06 W x D x H (mm)765 x 616 x 662 water Cooled/remote a. Ice maker potable water in, 3/8" FPT. B. Ice maker water out, 3/4" F PT. C. Hole for electrical connections, 7/8". D. Electrical connection junction box. E. Condenser water in, 3/8" FPT (water only). F. Condenser water out, 1/2" FPT (water only). G. Liquid line, 3/8" male quick connect coupling for precharged line set (remote only). H. Discharge line, 1/2" male quick connect coupling for precharged line set (remote only). I. Hole for remote electrical connections, 7/8" (remote only). nOTES: number of Wires: ICE1005/1006: 3 (including ground) • ICE1007: 4 (including ground) approx. Shipping Weight lbs (kg): ICE1006a 230 (105) • ICE1006r 235 (107) • ICE1006W 225 (102) • ICE1005a 230 (105) • ICE1005r 235 (107) • ICE1005W 225 (102) ICE1007a 230 (105) • ICE1007r 235 (107) • ICE1007W 225 (102) refrigerant Type: r404a EnErGY STar qualified machine. Please see our website www.iceomatic.com for the latest list of EnErGY STar qualified machines and available rebates specifications *Requires VRC 2061 Remote Condenser. MaxIMuM 60 Hz 50Hz ambient Temp. range air 50˚F (10˚C)100˚F (38˚C)110˚F (43˚C) Water Temp.40˚F (4.4˚C) Water Pressure 20 PSIG (1.4 Bar) 60 PSIG (4.1 Bar) MINIMuM 5" (127mm)Bin Strap5" (127mm)Bin Strap .8" (20 mm) 2.6"(67 mm) 17.7"(450 mm) 20.5"(521 mm) 22.2"(564 mm) B. C. D.A. .62" (16mm)Air In– Rear Standard Side Discharge 30.13"(765 mm) 26.06"(662 mm) 24.25"(616 mm) 22.2"(564 mm) 5" (127 mm)Bin Strap5" (127 mm)Bin Strap .7" (18 mm) 2.6"(67 mm).62" (16 mm) 17.7"(450 mm) 20.5"(521 mm) 22.2"(564 mm) E. D. F. B. C.A. 3.5" (89 mm) G.H. I. 5.4" (137 mm) 8.4" (213 mm) 10.0" (254 mm) 10.7" (272 mm) 12.3" (312 mm) model Number Cond. unit Ice Productionper 24hrs Water usagegallons per 100 lbs of Ice 90°F air/70°F water kWH Used per 100 lbs of ice @ 90°F air/ 70°F water Voltage Characteristics Min. Circuit Ampacity Fuse size Approx. bTus per hour 70°F air/ 50°F water lbs (kg) 90°F air/ 70°F water lbs (kg)Potable Condenser ICE1006aair 1000 (454) 760 (345)19.0 - 5.2 208-230/60/1 14.2 20 16,024 ICE1006r remote* 982 (446)843 (383)22.8 5.6 13.8 17,161 ICE1006W Water 960 (436) 856 (389) 23.4 113 4.3 12.8 15,355 ICE1005a air 964 (438) 766 (348)22.6 - 5.6 230/50/1 12 .6 16 15,594 ICE1005r remote* 926 (421) 778 (354) 21.8 15.2 15,838 ICE1005W Water 985 (448)871 (396)22.5 118 4.3 12.0 15,624 ICE1007a air 1000 (454) 800 (363) 23 - 5.2 208-230/60/3 12.2 15 15,490 ICE1007r remote* 910 (413) 781 (354) 21.9 5.2 10.8 15,317 ICE1007W Water 935 (425) 836 (380) 22.3 113 4.3 7.1 14,996 Air Cooled Water Cooled & Remote 10475 International product 5/21/2018 5 11/16 [144]R3/4 [R19]8 3/16 [208] 1 3/16 [29] Ⱦ1 3/8" [35] DRAIN HOLE TO BE DIMPLED MIN. 1/8" [3] IN DEPTH TO ENSURE BRASS DRAIN FITS FLUSH 16 3/8 [416] WRAP16 3/16 [411]16 [406]R3/4 [R19] 11 3/8 [289] WRAP 12 5/16 [313]15 [381] 17 5/16 [440]10 [254]TUB TO BE DIE STAMPED TO A MINIMUM 1/4" [6] DEPTH TO ENSURE PROPER DRAINAGE6 5/8 [168] WELDSTUD PLACEMENT1 11/16 [43] 11 3/4 [299] WELD STUD PLACEMENT 1 5/8 [41] LID NOT SHOWN IN TOP VIEW12 9 / 1 6 [ 3 1 9 ] 17 9/ 1 6 [ 4 4 6] DRAWN BY: REV REV DATE: FSP #: ITEM #: CUSTOMER: PROJECT: NSF ID: SHEET: THIS PRINT IS THE PROPERTY OF ELKAY MANUFACTURING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. GENERAL NOTES: 1. NO BURRS OR DIE MARKS PERMISSIBLE 2. ALL WELDS TO BE GROUND SMOOTH AND POLISHED TO A MATCHING FINISH 3. OVERALL DIMENSION TOLERANCE (UNLESS NOTED OTHERWISE) 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.35] STARBUCKS 45LB ICE BIN W/ SIDE ACCESS LID CUSTOM COMPONENT FSP211635 TCP / DW01/17/18 1 OF 4 C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LB ICE BIN - SIDE ACCESS.DWG 19278 5/21/2018 Ⱦ1/4 [6] 1 [ 2 5 ] 8 1 / 2 [ 2 1 6 ] 13 1/ 2 [ 3 4 3] 1 [25 ] 1 [25] Ⱦ7/8 [22] ATTACH TO INSULATED WRAP BY MEANS OF 4 EACH WELD STUDS AND STUD CAPS PERFORATED TRIVET ALL CORNERS FULLY WELDED AND POLISHED 18 GA. [1.2] CONSTRUCTION PERFORATED TRIVET TO FIT INSIDE TUB RADIUS AND HAVE FINGER HOLES FOR REMOVAL BIN SECTION VIEWS 17 5/16 [440] 16 3/8 [416]11 3/8 [289] 12 5/16 [313] 1 1/2 [38] 1 1/4 [32] 2 [51] 11/16 [18] 7/16 [10] 7/16 [10]16 3/16 [411]1" NPS BRASS DRAIN WITH FLANGED ZINK LOCKNUT AND RUBBER WASHER5/8 [16]5/8 [16]7/16 [11] Ⱦ1 3/8" [35] DRAIN HOLE TO BE DIMPLED MIN. 1/8" [3] IN DEPTH TO ENSURE BRASS DRAIN FITS FLUSH 14 GA. [2.0] CONSTRUCTION TOP 16 GA. [1.5] CONSTRUCTION TUB FULLY WELDED AND POLISHED TO A 304 #4 FINISH 20 GA. [1.0] 304 S/S CONSTRUCTION WRAP TO BE INSULATED WITH 1/2" [13] FOIL FACED RIGID FOAM AT SIDES AND BOTTOM (SILICONE ALL SEAMS) Ⱦ2 5/8" [Ⱦ67] BY 1/2" [13] TALL S/S RING STITCH WELDED TO INSIDE OF WRAP (SILICONE INSIDE SEAM) FUSE WELD 1" [25] LONG WELD STUD TO BOTTOM OF INNER TUB Ⱦ3/8" [Ⱦ10] HOLES IN INSULATION AND WRAP FOR WELD STUD WELD STUD AND CAP DETAIL Scale: N.T.S. DRAWN BY: REV REV DATE: FSP #: ITEM #: CUSTOMER: PROJECT: NSF ID: SHEET: THIS PRINT IS THE PROPERTY OF ELKAY MANUFACTURING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. GENERAL NOTES: 1. NO BURRS OR DIE MARKS PERMISSIBLE 2. ALL WELDS TO BE GROUND SMOOTH AND POLISHED TO A MATCHING FINISH 3. OVERALL DIMENSION TOLERANCE (UNLESS NOTED OTHERWISE) 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.35] STARBUCKS 45LB ICE BIN W/ SIDE ACCESS LID CUSTOM COMPONENT FSP211635 TCP / DW01/17/18 2 OF 4 C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LB ICE BIN - SIDE ACCESS.DWG 19278 5/21/2018 LID ASSEMBLY SECTION 3/4" RADIUS HALF ROLLED RAISED INTEGRAL HANDLE WITH EASED CORNERS FRONT LID SECTION 3 7/8 [99] 3 [76] LID CLOSED 5/8 [16]12 9/16 [319] 3 3/8 [86] LID OPEN 1/2 [13]1 3/4[44]DETAIL -B- PAGE 4 OF 4 6 [152] NSF STICKER (COMPONENT) 16 GA. [1.5] 304 #4 S/S LID FRAME 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 18 GA. [1.2] 304 #4 S/S CONSTRUCTION A A FULLY WELD & POLISH ALL CORNERS 13 [ 3 3 0 ] (2) 1/4"x1/2" [6x13] S/S THREADLESS WELD STUDS W/ (2) ADDITIONAL TACK WELDS 15 [ 3 8 1 ] I.D . 10 [2 5 4]I.D. 17 9 / 1 6 [ 4 4 6 ] 12 9/ 1 6 [ 3 1 9] 5/8 [16] 1/2 [13] 1 5/16 [33] SECTION A-A SCALE: NTS NOTE: SECTION TYP. @ 4 SIDES 3/16 [5] 11/16 [18] 5/8 [16] MARINE EDGE DETAIL Scale: NTS DRAWN BY: REV REV DATE: FSP #: ITEM #: CUSTOMER: PROJECT: NSF ID: SHEET: THIS PRINT IS THE PROPERTY OF ELKAY MANUFACTURING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. GENERAL NOTES: 1. NO BURRS OR DIE MARKS PERMISSIBLE 2. ALL WELDS TO BE GROUND SMOOTH AND POLISHED TO A MATCHING FINISH 3. OVERALL DIMENSION TOLERANCE (UNLESS NOTED OTHERWISE) 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.35] STARBUCKS 45LB ICE BIN W/ SIDE ACCESS LID CUSTOM COMPONENT FSP211635 TCP / DW01/17/18 3 OF 4 C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LB ICE BIN - SIDE ACCESS.DWG 19278 5/21/2018 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 18 GA. [1.2] 304 #4 S/S CONSTRUCTION 4 1/4 [108] O.D. 15 5 / 1 6 [ 3 8 9 ] O. D . 11/16 [17] 1/2 [13] DIE STAMP UP 1/8" MINIMUM R3/4 [R19]4 3/16 [107] O.D. 1 7/16 [37] 3 13/16 [97] 1/2 [13] DIE STAMP UP 1/8" MINIMUM 1 [25] BACK FLANGE W/ 2 EA. HOLES TO SLIDE OVER THREADLESS WELD STUDS 15 1 1 / 1 6 [ 3 9 9 ] O. D . 3 3/8 [86] O.D. DIE STAMP UP 1/8" MINIMUM 15 1 / 2 [ 3 9 4 ] O. D . 3 7/8 [99] O.D. 11/16 [18] 11/16 [18] 2 1/8 [54] O.D.5/8[16]11/16 [17] 7/16 [11] DETAIL -B- DRAWN BY: REV REV DATE: FSP #: ITEM #: CUSTOMER: PROJECT: NSF ID: SHEET: THIS PRINT IS THE PROPERTY OF ELKAY MANUFACTURING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. GENERAL NOTES: 1. NO BURRS OR DIE MARKS PERMISSIBLE 2. ALL WELDS TO BE GROUND SMOOTH AND POLISHED TO A MATCHING FINISH 3. OVERALL DIMENSION TOLERANCE (UNLESS NOTED OTHERWISE) 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.35] STARBUCKS 45LB ICE BIN W/ SIDE ACCESS LID CUSTOM COMPONENT FSP211635 TCP / DW01/17/18 4 OF 4 C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LB ICE BIN - SIDE ACCESS.DWG 19278 5/21/2018 Project Price Quantity Total Shipping ECL-NS-A34P Surface Mount Stainless Steel Starbucks Tall Hot Paper Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-A34P (SKU #194318) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.2 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (41 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 526 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-A34P 23” 4.000” 3.688” 3.750” 1.375” 9.000”Tall Hot Paper Cup “D” “E” “F” “A” 10091 5/21/2018 10305 5/21/2018 ® 10384 5/21/2018 5/21/2018 5/21/2018 3/16 5/21/2018 Project Price Quantity Total Shipping ECL-NS-299P Surface Mount Stainless Steel Starbucks Short Hot Paper Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-299P (SKU #194320) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.0 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (39 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 500 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-299P 23” 3.625” 3.312” 3.406” 1.375”9.000” Short Hot Paper Cup “D” “E” “F” “A” 10396 5/21/2018 Project Price Quantity Total Shipping ECL-NS-845P Surface Mount Stainless Steel Starbucks Grande/Venti Cold Plastic Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-845P (SKU #194319) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.5 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (45 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 573 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-845P 23” 4.500” 4.062” 4.188” 1.375”9.000”Grande/Venti Cold Plastic “D” “E” “F” “A” 10791 5/21/2018 Project Price Quantity Total Shipping ECL-NS-31P Surface Mount Stainless Steel Starbucks Grande/Venti Hot Paper Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-31P (SKU #194322) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.2 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (41 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 526 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-31P 23” 4.000” 3.688” 3.750” 1.375” 9.000”Grande/Venti Hot Paper Cup “D” “E” “F” “A” 10855 5/21/2018 Project Price Quantity Total Shipping ECL-NS-422P Surface Mount Stainless Steel Starbucks Tall Cold Plastic Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-422P (SKU #194321) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.3 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (42 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 536 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully supports the dispenser and allows tool-free removal for cleaning. “A” “B” “C” “D” “E” “F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-422P 23” 4.188” 3.812” 3.938” 1.375” 9.000” Tall Cold Plastic Cup “D” “E” “F” “A” 10858 5/21/2018 Georgia-Pacific Professional 133 Peachtree NE Atlanta, GA 30303 1-866-HELLO GP (435-5647) | www.gppro.com printed on 3/10/2010 mmkaye@gapac.com GP® Countertop Dispenser for Folded Paper Towel VISTA® BigFold® / C-Fold counter top dispenser keeps towels next to the wash basin when dispenser mounting is not an option. Item Description: VISTA® paper towel dispensers hold one package of BigFold® or C-Fold paper towels to offer protection from moisture and contaminants on countertops when towels cannot be located near all wash basins. Made from high-impact plastic in an attractive translucent smoke color, these durable dispensers offer a reliable and cost-effective dispensing solution for a variety of areas. Features & Benefits: »High-Impact plastic construction is durable, washable, and stands up to most cleaning agents, ensuring years of cost-saving performance »Offers an economical approach to C-Fold towel dispensing »Protects towels from moisture on the countertop Product Details Brand Owner Georgia-Pacific Brand GP® MFG Item#56640 Design Translucent Smoke UPC UCC-12 073310566405 Each Per Ship Unit 6 Each Items Per Each 0 Each Case Total 6 Each Dispenser (WxDxH)0.000" x 0.000'' x 0.000" UNSPSC 47131701 Buy Multiple 6 EA Case Shipping Info GTIN 10073310566402 Case Gross Weight 9.180 lbs Case Net Weight 5.100 lbs Case Dimensions 14.620" x 11.940" x 16.100" Case Volume 1.626 CFT Each Shipping Info: Each Gross Weight 1.14 lbs Each Net Weight 0.85 Each Dimensions 11.300" x 7.520" x 4.610" Each Volume 0.227 CFT Unit Shipping Info Ti-Qty/Layer 66 High-Layers/Unit 6 Unit Qty 396 Unit Dimensions (LxWxH) 47.560" x 41.000" x 96.625" 0 73310 56640 5 SKU: 375372 TAG: M055/M155 DESCRIPTION: Dispenser, ‰ Size MANUFACTURER: MODEL NUMBER: Georgia-Pacific 56640 10992 5/21/2018 The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 8/9/10 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2010 by Gamco Commercial Restroom Accessories, A Division of Bobrick. 3-3/8" 86mm DIA. 4" 102mm 2-11/16" 68mm 8-1/4" 210mm Adjustable to Counter Thickness 4" 102mmMaximum 1-7/8" 48mmDIA. ConstruCtion: Basin-mounted soap dispenser has polyethylene globe. Units are designed to be filled from the top for easy maintenance. 4" (102mm) long spout directs soap flow over sink. Exposed portions are chrome-plated brass to match the existing faucets. CapaCity: 8-1/4" (210mm) globe - 32-fl oz. (0.9-L) overall Dimensions: Unit requires 1" (25mm) hole in the vanity or basin. mounting: Mounting location for push button dispensers are 44" (1118mm) maximum above the finish floor. aDa guiDe: Push buttons and pistons should be operable with one hand and without tight grasping, pinching, or twisting of the wrist. Activation of soap valves should not require more than 5 pounds of force when unit is completely filled. Spout shall rotate 360° without damage to valve mechanism. note: Soap dispenser shall dispense liquid lotion soaps, and synthetic detergents. Basin-Mounted Soap Dispenser with All-Purpose Valve shall be Model G-64LB of GAMCO Commercial Restroom Accessories, A Division of Bobrick, One Gamco Place, Durant, OK basin-mounteDsoap Dispenser with all-purpose valve g-64lb Date: Project Name: 11115 5/21/2018 SPG MODEL No: STBKCCAD8B LK CUP CADDY (HOLDS 8 CUP DISPENSERS) m Ltr REVISION DESCRIPTION BY Dote ECO/NPR A APPROVED SHOWN HERE WITH CUP DISPENSERS PW 01.18.12 9093 c--------21.12"-----� ,-,------- 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ' NOTE: CUP DISPENSERS NOT INCLUDED, SUPPLIED BY OTHERS 11.87'' ' ' o·, 'o' ) ( ' , ' , OD 7 4.76" �---�--· PROPRIETAR'I' NOTICE: Tlti<St�adamci:aljefyfbl,, 0 0 Weight 0 0 Locking Caster Cube 0 0 0 0 8 8 Fixed Caster 8 8 Description: 0 0 0 0 8 8 Swivel Non-locking Caster 30.81" .� ...... :I �p1e.uy ar 26.5 lbs. 5.18 cu.ft. STARBUCKS CUP CADOY 12x21x31H i-------'--------1 (HOLDS 8 CUP DISPENSERS) SfORI.Gf PRODUCTS GR P ;&·w 5-0RACiEP1:ilODUC1SGaOUP NTERNA'Tl:'.Jet-'1,I. U.C. /lnJper"Aft�IMs� ;-:incL'Or��brzate, m �.irz;e «d.l).b'tan �������'!.�on�d... �02D1D S,�A:Dtt.a.�..p. ri� File Name: 104097_S01_A-Model# STBKCCAOBBLK Date: Material· Finish: 09.29. 10 ALUMINUM BLACK Drawn By: Drawing Size: Scale; Sheet: Rev: Sketch No. PW A NG 1 of l A 104097 13330 5/21/2018 SPG MODEL No: STBKCCADSBLK Ai Carriage Bolt QTY:4 B� Lock Washer QTY:4 c� Wing Nut QTY:4 Caddy Top QTY: 1 D Caddy Base QTY: 1 E CUP CADDY (HOLDS 8 CUP DISPENSERS) Ltr REVISION DESCRIPTION A APPROVED B UPDATED PACKAGE TO SHOW TOOTH-LOCK WASHER jA I @;/ I I BY Date ECO/NPR PW 01.10.12 9093 JSW 01.18.13 9093 ............ PROPRIETARY NOTICE: �11".e,etccdam.o:t.1(jefrt�l, Weight Cube Description: ASSEMBLY INSTRUCTTONS (15104097) ,_2_6_.5_lbs_.�_5·_1B_cu_.f_t._, STARBUCKS CUP CADDY 12x21x31H .::111 ..... � STD E PRODUCTS GR P -�-pre� ·,oar S ORAGE flliDOlJCTE, GaOUP NT�"Tl;)M,_.\l... LlC. /1,r,rJper-..oo..xa;izaOis·meiet i1n4'«��1:.r=..,te ro!S-'..cb51n;,, u�7c,?1itm �����ii: st1e,eton� �oi!l1[l, S�·Pmd:d.QQ:;ct,. r!� Ale Name: (HOLDS 8 CUP DISPENSERS) 104097 _l01-B-Model# STBKCCADBBLK Date: Material: Rnlsh: 08 .10.11 ALUMINUM BLACK Drawn By: Drawing Size: Scale: Sheet: Rev: Sketch No. PW A NTS 1 of 2 B 104097 13330 5/21/2018 SPG MODEL No: STBKCCADSBLK NOTE: CUP DISPENSERS NOT INCLUDED, SUPPLIED BY OTHERS I ---- CUP CADDY (HOLDS 8 CUP DISPENSERS) Ltr REVISION DESCRIPTION A APPROVED BY Date ECO/NPR PW 01.10.12 9093 B UPDATED PACKAGE TO SHOW TOOTH-LOCK WASHER JSW 01.18.13 9093 ··�--1 · .:�•1 .... ::11 sro E PRODUCTS GR p PROPRIETARY NOTICE: Tht.-stitttalida'm.o:dl�I,, �� ooor ST0R.\GE Pfil08UCTSGROUP NTEfiNA"TIJKI\L, u.c. 1Wjper-..on�:ali1Ji·� and.'or��b�..ue .oo �.u:.earQ4'l..:atan ������ shffl:on� �O�D1D· ::.��Gro.=-1). rt� Hot Cold Weight Cube Description: ASSEM BLY INSTRUCTTONS (15104097) .,_2_6_.5 _lb_s_. �5_·1_B_c_u.f_t._, STAR BUCKS CUP CADDY 12x21x31H Ale Name: (HOLDS 8 CUP DISPENSERS) 104097 _l01-B-Model# STBKCCADBBLK Date: Material: Rnlsh: 08.10.11 ALUMINUM BLACK Drawn By: Drawing Size: Scale: Sheet: Rev: Sketch No. PW A NTS 2 of 2 B 104097 13330 5/21/2018 Project Price Quantity Total Shipping ECL-NS-69P Surface Mount Stainless Steel Starbucks Trenta Cold Plastic Cup Dispenser Diversified Metal Products, Inc. 2205 Carlson Drive • Northbrook, IL 60062 • (847) 753-9595 • fax (847) 753-9648 www.dispense-rite.com • sales@dispense-rite.com Model Number: ECL-NS-69P (SKU #TBD) Inner Carton Dimensions (1each): 23.5” x 5.75” x 5.75” (3.6 lbs) Master Carton Dimensions (12 each): 24” x 24” x 18” (46 lbs) Units per skid: 144 pcs (12 master cartons) Skid Dimensions: 77” H x 48” W x 40” D Skid Weight: 575 lbs. “B” BODY CAP “C” • Fixed diameter dispenser (no adjustment required) • Stainless steel construction • No-jam design • All models are NSF Listed • Quick release mounting brackets fully support the dispenser and allows tool-free removal for cleaning. “A”“B”“C” “D” “E”“F” Model Overall Overall Tube End Cap Top Bracket Bottom Bracket No. Length Diameter Diameter Diameter Spacing Spacing Cup Type ECL-NS-69P 23” 4.625” 4.3125” 4.375” 1.375” 9.000”Trenta Cold Plastic Cup “D” “E” “F” “A” Other_13584_Doc1 13584 5/21/2018 Parker Gas Blender Panel Installation Instructions (800) 343-4048 www.parker.com/gsf 4087 Walden Avenue, Lancaster, NY 14086 Gas Blender Panel 18980 5/21/2018 Parker Limited Five Year Warranty Warranty not valid outside the Continental USA If the mechanics of this product are found to be defective in materials or workmanship within five years from the date of purchase, Parker will repair or replace, at its option, the defective product or component part. If for any reason the original purchaser is unsatisfied with the performance of this product, Parker will, at the purchaser’s option, replace the product or refund the original sale price upon return of this product to Parker. Please retain receipt for proof of purchase. Proof of purchase is required for any warranty service or claim. Your receipt is your warranty card. LIMITED WARRANTY Parker warrants each product to be free from defects in material and workmanship under normal use and service for five years from date of sale. The obligation of Parker under this warranty is limited to the replacement of defective parts. Notice of defective parts must be submitted to Parker within five year and 15 days of date of sale. This warranty does not cover shipping, handling, or freight charges. DISCLAIMER OF WARRANTY WARRANTY IS INVALID IF PURCHASER FAILS TO PROPERLY OPERATE AND/OR MAINTAIN THE PRODUCT. THIS WARRANTY IS NOT TRANSFERABLE TO THIRD PARTIES. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES AND REPRESENTATIONS, EXPRESSED OR IMPLIED EXCEPT AS STATED ABOVE. THERE IS NO WARRANTY FOR FITNESS FOR A PARTICULAR PURPOSE OR WARRANTY OF MERCHANTABILITY. EXCEPT AS OTHERWISE AGREED HEREIN PARKER SHALL NOT BE LIABLE FOR SPECIAL OR CONSEQUENTIAL DAMAGES, SUCH AS, BUT NOT LIMITED TO DAMAGE TO OR LOSS OF OTHER PROPERTY OR EQUIPMENT, LOSS OF PROFIT OR REVENUE, LOSS OF USE OF THE PRODUCT , COST OR REPLACEMENT OF THE PRODUCT, OR CLAIMS BY CUSTOMERS FOR LOSS DUE TO SERVICE INTERRUPTIONS. THE REMEDIES OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE LIABILITY OF PARKER. WITH RESPECT TO ANY CONTRACT SHALL NOT, EXCEPT AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE EQUIPMENT OR PART ON WHICH SUCH LIABILITY IS BASED. This warranty applies only to the original registered purchaser. TAMPERING, ACCIDENT, ABUSE, NEGLECT, UNAUTHORIZED REPAIRS OR OTHER CAUSES UNRELATED TO DEFECTIVE MATERIALS OR WORKMANSHIP WILL VOID THIS WARRANTY. Parker neither assumes nor authorizes any representative or other person to assume for us any liability in connection with the sales or any shipment of our products. PLEASE KEEP INSTRUCTIONS WITH YOUR PURCHASE RECEIPT FOR YOUR RECORDS! 5/21/2018 Installation Instructions for the Single / Single High Flow / Double / Double High Flow Parker Gas Blender Panel Thank You for purchasing the Parker Gas Blender Panel. Our goal is to give you the most dependable, accurate and straight forward blender possible for food packaging, welding or other related uses and products. We want you to be thoroughly happy with your new system and would like to hear from you if for any reason you are, in any way, displeased. The Parker Gas Blender Panel is simple to install and use. It is extremely accurate, reliable and requires little maintenance. Properly installed, and supplied with clean, dry gas, your Parker Gas Blender Panel will provide a perfect supply of mixed gas for many years. Please take the time to read and understand the instructions, the system and the cautions. While the system is simple there are inherent dangers in working with pressurized gases. Pressure vessels and storage tanks, which contain both liquids and pressurized gases, can explode or rupture and cause serious injury or death if over-pressurized or used incorrectly. Be 100% sure you understand the implications of what you are doing whenever you set up, turn on or modify this or any system. Check with your equipment supplier (in the case of storage tanks especially) to be sure you are not exceeding any safety limits. If you have any doubt concerning the safety of your system, get advice from or have the work done by a qualified specialist. Caution With the Parker Gas Blender Panel you are dealing with pressurized gases. Serious injury or death can result from improper installation, use or service. All work on these systems should be carried out by qualified personnel only! Before attempting any work on this system be sure to read and understand these and any other instructions that relate to the equipment involved in these systems! The dangers include, but are not limited to, EXPLOSION if the maximum safe pressures for any of the individual components of the system are exceeded or ASPHYXIATION if gases are released or leaked into a confined area. If you have any questions regarding the safety of these systems do not proceed with the installation or operation until you are 100% certain as to their safety! 5/21/2018 Warning With this or any compressed gas system there are certain dangers. If you do not have the experience to understand these dangers use a professional installer. NOTE These instructions apply to the Parker Single and Parker Double as well as their respective High Flow models. The picture to the right is of a Parker Double. The Parker Single will have only one outlet assembly, which is on the right-hand side. Use primary regulators on your gas source suitable for your panel specifications. Example: If your inlet pressure label states “Min. inlet pressure 70 psi” then you must provide at least 70 psi to the Blender Panel. Mixed Gas Out Use reinforced tubing suitable for 150 psi. N2 CO2 1. Use thread sealant. 2. Do not remove fittings. 3. Use back-up wrenches. Parker Gas Blender Panel Installation Instructions (800) 343-4048 www.parker.com/gsf 4087 Walden Avenue, Lancaster, NY 14086 Gas Blender Panel 5/21/2018 Step 1: Determine the best location for the blender! Please consider the following: A) Select a location that minimizes the chance of accidental damage to the blender. B) Select a location as near as is practical to both the supply sources and the supplied equipment. C) Select a location allowing convenient access to the shut off valve for servicing. D) Mount panel in a weather-proof area only. Step 2: Mount panel to wall! Step 3: Hook up gas supply and outlet! A) Use only the gases shown on the panel label(s). B) Make sure you are supplying the panel with clean, dry gases that are between the minimum and maximum pressures as indicated on the panel label. C) Turn shut-off valve(s) on panel to the off position. D) Make sure the tubing from the gas sources is compatible with the fittings on the panel. DO NOT ATTEMPT TO REMOVE INLET OR OUTLET FITTINGS. E) Install appropriate tubing adaptors in the inlet fittings. Be sure to use thread sealant and back-up wrenches. Connect gases supply lines to inlet fittings. F) Confirm that your system and related equipment is safe and ready for pressurized mixed gas. G) Connect mixed gas supply tube to mixed gas outlet fitting. H) Turn on the supply gases and check supply system and fittings for leaks. I) Adjust outlet pressure regulator to desired outlet pressure. Read outlet pressure on Outlet Pressure Gauge. J) Open mixed gas supply shut off valve and check system for leaks. Installation Instructions 5/21/2018 Operation Guidelines and Helpful Hints NOTES: 1) Supply the panel with clean gases. 2) Be sure no liquid can get into the blender as this will render it useless and void the warranty. 3) Some fittings on the panel do not have standard US threads, and should not be removed with out checking with Parker! 4) Never exceed the recommended pressures for any part of your system! Adjusting the outlet pressure. 1) Close shut-off valve. This allows you to read pressure changes quickly. 2) Pull out the adjusting stem of regulator. 3) Read pressure on pressure gauge. 4) Adjust pressure. Increase by turning clockwise. Note: When decreasing pressure, always reduce pressure to below the desired level and then increase to desired setting. 5) Push in adjusting stem of regulator to lock. 6) Open shut-off valve. Trouble-shooting: No Outlet Gas. 1) Close shut-off valve. Check pressure on pressure gauge. If pressure is low or zero, check: a) Outlet regulator for adjustment. (See “Adjusting the outlet pressure” above.) b) Both supply gases. (One or both could be empty, turned off or out of adjustment.) c) For blockage of either supply line or for a closed valve within the supply system. (The blender shuts off if either supply gas is unavailable.) If pressure is good: d) Open shut-off valve completely. 2) If you continue to have no gas, close shut-off valve, remove tubing from outlet, open shut-off valve and check for gas flow. 3) If you still have no supply gas, call Parker or your gas supplier or service person. There are no user-serviceable parts within the panel. Anything done to the internal parts will affect the blend and void the warranty. If you encounter other questions or problems call: Parker GSF (800) 343-4048 or (716) 686-6400. 5/21/2018 Notes 5/21/2018 Bulletin Blender Panel 04/2017© 2017 Parker Hannifin Corporation Parker Hannifin Corporation Gas Separation and Filtration Division 4087 Walden Avenue Lancaster, NY 14086 phone 716 686 6400 fax 877 857 3800 www.parker.com/gsf North America Compressed Air Treatment Gas Separation & Filtration Division Lancaster, NY 716 686 6400 www.parker.com/gsf Haverhill, MA 978 858 0505 www.parker.com/gsf Engine Filtration Racor Modesto, CA 209 521 7860 www.parker.com/racor Holly Springs, MS 662 252 2656 www.parker.com/racor Hydraulic Filtration Hydraulic & Fuel Filtration Metamora, OH 419 644 4311 www.parker.com/hydraulicfilter Laval, QC Canada 450 629 9594 www.parkerfarr.com Velcon Colorado Springs, CO 719 531 5855 www.velcon.com Process Filtration domnick hunter Process Filtration SciLog Oxnard, CA 805 604 3400 www.parker.com/processfiltration Water Purification Village Marine, Sea Recovery, Horizon Reverse Osmosis Carson, CA 310 637 3400 www.parker.com/watermakers Europe Compressed Air Treatment Gas Separation & Filtration Division EMEA Gas Generation/Compressed Air and Gas Treatment Gateshead, England +44 (0) 191 402 9000 www.parker.com/gsfe Membrane and Modules Etten-Leur, Netherlands +31 76 508 5300 www.parker.com/gsfe Hiross Zander Essen, Germany +49 2054 9340 www.parker.com/gsfe Padova, Italy +39 049 9712 111 www.parker.com/gsfe Engine Filtration & Water Purification Racor Dewsbury, England +44 (0) 1924 487 000 www.parker.com/rfde Racor Research & Development Stuttgart, Germany +49 (0)711 7071 290-10 Hydraulic Filtration Hydraulic Filter Arnhem, Holland +31 26 3760376 www.parker.com/hfde Urjala, Finland +358 20 753 2500 Condition Monitoring Parker Kittiwake West Sussex, England +44 (0) 1903 731 470 www.kittiwake.com Process Filtration domnick hunter Process Filtration Parker Twin Filter BV Birtley, England +44 (0) 191 410 5121 www.parker.com/processfiltration Asia Pacific Australia Castle Hill, Australia +61 2 9634 7777 www.parker.com/australia China Shanghai, China +86 21 5031 2525 www.parker.com/china India Chennai, India +91 22 4391 0700 www.parker.com/india Parker Fowler Bangalore, India +91 80 2783 6794 www.johnfowlerindia.com Japan Tokyo, Japan +81 45 870 1522 www.parker.com/japan Korea Hwaseon-City +82 31 359 0852 www.parker.com/korea Singapore Jurong Town, Singapore +65 6887 6300 www.parker.com/singapore Thailand Bangkok, Thailand +66 2186 7000 www.parker.com/thailand Latin America Parker Comercio Ltda. Filtration Division Sao Paulo, Brazil +55 12 4009 3500 www.parker.com/br Pan American Division Miami, FL 305 470 8800 www.parker.com/panam Africa Aeroport Kempton Park, South Africa +27 11 9610700 www.parker.com/africa Worldwide Filtration Manufacturing Locations 5/21/2018 X4000 5/21/2018 ISSUED: REVISED: MODEL No: Accessory Specialties AMERICAN DISPENSER Desert Ray Products ,INC. THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE SURFACE MOUNTED TWIN HIDE-A-ROLL TOILET TISSUE DISPENSER 0030AMERICAN SPECIALTIES, INC. www.americanspecialties.com 441 Saw Mill River Road, Yonkers, NY 10701 (914) 476-9000 01-87 01-08 SPECIFICATION Surface Mounted Twin Hide-A-Roll Toilet Tissue Dispenser shall hold and dispense two (2) standard or two (2) 5- 1/4" diameter (Ø133) 1800 sheets tissue rolls and shall have door, door frame, and dispensing mechanism fabricated of alloy 18-8 stainless steel, type 304, 18 gauge; cabinet body shall be same grade, 22 gauge. All exposed surface shall be No 4 satin finish and be protected during shipment with a PVC film easily removable after installation. Internal mechanism levers shall be fabricated of molded high-impact resistant plastic for smooth operation. Structural assembly of body and door components shall be of welded construction. Door hinge shall be of heavy-duty stainless steel 3/16" diameter (Ø4.8). Door shall be held closed with a tumbler lock keyed alike to other ASI washroom equipment. Cabinet shall include theft resistant and vandal resistant rollers that shall be of molded high-impact resistant plastic with integral molded-in stainless steel end pins and two (2) rollers [p/n R-004] shall be supplied. Surface Mounted Twin Hide-a-Roll Toilet Tissue Dispenser shall be Model No 0030 as manufactured by American Specialties, Inc. 441 Saw Mill River Road Yonkers, New York 10701-4913 INSTALLATION Unit is surface mounted on wall or partition using four (4) No10 self-tapping screws (by others). Top two mounting holes through back are “keyhole” slots for ease in hanging unit on pre-installed screws. Bottom two mounting holes are horizontal slots for ease of adjustment. For compliance with ADA Accessibility Guidelines, top of unit should be installed 29" (737 mm) above finished floor. OPERATION Reloading instructions are printed on graphic label inside door. Bottom roll is depleted prior to top roll automatically dropping into lower position for use. Empty rollers can not be removed without key unlocking door. 6"[152] 12" [305] 2-12" [64] 7"[178] 3" [76] 1-12"[38] PIN TUMBLER LOCK MOUNTING HOLES CONCEALED ON REAR WALL HINGE PIVOT 3"[76] 6-12"[165] 11-7 8"[302] 5-3 4" [146] NOTE: ALL DIMS ARE INCH [MM] 10099 X10099 5/21/2018 The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 1/24/14 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2014 by Gamco Commercial Restroom Accessories, A Division of Bobrick. Rear View 2" 51mm 11" 279mm 8" 203mm 15-3/4" 400mm 4" 102mm 1-9/16" 40mm 1-9/16" 40mm Average Mounting Height Off Floor45" to 59" 1145 to 1500mmAverage Mounting Height Off FloorFor Accessible Design30" to 45" 760 to 1145mmS S Finish Face of Wall surface mounted seat-coVer dIsPenser tsc-1 materIaLs: 18-8, type-304, 22-gauge (0.8mm) stainless steel with satin finish. All-welded construction with beveled opening. oPeratIon: Dispenses single- or half-fold paper toilet seat covers from beveled opening. Dispenser fills from bottom through concealed opening. Capacity: 250 toilet seat covers. InstaLLatIon: Mount unit on wall or toilet partition with two flat-head screws, not furnished by manufacturer, at points indicated by an S. For plaster or dry wall construction, provide concealed backing that complies with local building codes, then secure unit with flat-head screws not furnished. For other wall surfaces, provide fiber plugs or expansion shields for use with screws, not furnished, or provide 1/8'' (3mm) toggle bolts or expansion bolts. Note: Provide a 5'' (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection to provide room for filling dispenser from bottom. sPecIfIcatIon: Surface-mounted toilet-seat-cover dispenser shall be type-304, 22-gauge (0.8mm) stainless steel with all-welded construction; exposed surfaces shall have satin finish. Dispenser shall have a concealed opening in bottom for filling. Capacity shall be 250 paper toilet seat covers Surface-Mounted Seat-Cover Dispenser shall be TSC-1 of Gamco Commercial Restroom Accessories, A Division of Bobrick, One Gamco Place, Durant, OK X10172 5/21/2018 AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com 9 32" DIA [Ø7] HOLES WITH .40" DIA [Ø10.2] X 82° COUNTERSINK TO ACCOMMODATE #10 (M5) FLAT HEAD SCREWS OR 1/4" (M6) PAN HEAD SCREWS 120° 18" [3] 3" DIA [Ø76] PEENED OPTION NOTE: ALL DIMS INCH [MM] 1-14" DIA [Ø32]1-12" [38] FINISHED WALL 2-14" DIA [Ø57] BC THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE 1-1/4" DIA (Ø32) GRAB BAR SERIES WITH FLANGES FOR EXPOSED MOUNTING MODEL №: 3400 ISSUED: 01/87 REVISED: 6 Dec 2012 SPECIFICATION Grab Bar with Flanges for Exposed Mounting shall be type 304 stainless steel alloy 18-8. Tubing shall be 1-1/4" diameter (Ø32) x 18 gauge [0.048"] (1.2). Flange shall be 11 gauge 1/8" (3) thick and shall be Heliarc welded to tubing with a continuous concealed bead. Flanges shall have three (3) countersunk 9/32" diameter (Ø7) holes to accommodate 1/4" diameter [Ø6] pan head or № 10 self-tapping flat head or oval head mounting screws (not provided). All exposed surfaces shall have a satin finish and shall be protected during shipment with a plastic bag. For optional non-slip surface add suffix –P (peened). 1-1/4" Diameter (Ø32) Grab bar with Flanges for Exposed Mounting shall be Series № 3400 of American Specialties, Inc., 441 Saw Mill River Road, Yonkers, New York 10701- 4913 STRENGTH ASI Grab Bars are designed to meet and exceed ADA requirements as published in CABO/ANSI A117.1 and 2010 ADA Accessibility Standards. Mounting to the wall is a critical part of the system to meet this require- ment. To withstand the shear, tension or pullout, and torsion loads generated by the maximum loading, the fas- tener system must be adequately sized. INSTALLATION Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using three (3) № 10 self-tapping flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange. Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing. For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33" (840) minimum above finished floor (AFF) to 36" (915) maxi- mum AFF. Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series). 10769 X10769 5/21/2018 AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE GRAB BAR CONFIGURATIONS (PG 1 OF 3) MODEL №: GRABBAR CONFIG ISSUED: 09/96 REVISED: 6 Dec 2012 SCHEDULE QTY. DIM. A QTY. DIM. A 12" [305] 36" [914] 18" [457] 42" [1067] 24" [610] 48" [1219] 30" [762] SCHEDULE QTY. DIM. A 52" [1321] 54" [1372] 60" [1524] 72" [1829] TYPE -01 TYPE -02 TYPE -04 TYPE -15 SCHEDULE QTY. HAND LH RH LH SHOWN RH OPPOSITE MODEL № MUST SPECIFY -LH OR -RH 33" [838] 30" [762] 3" [76] PROJECTION BELOW FINISHED FLOOR CONTRACTOR TO PROVIDE PROPER SLEEVE IN FLOOR X 3" LONG TO ACCEPT BAR OD SPECIFIED. 28" [711] 32" [813] 18" [406] 90° 1-1/2" [38] ALL DIMS INCH [MM] A 10769 5/21/2018 AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com 9 32" DIA [Ø7] HOLES WITH .40" DIA [Ø10.2] X 82° COUNTERSINK TO ACCOMMODATE #10 (M5) FLAT HEAD SCREWS OR 1/4" (M6) PAN HEAD SCREWS 120° 18" [3] 3" DIA [Ø76] PEENED OPTION NOTE: ALL DIMS INCH [MM] 1-14" DIA [Ø32]1-12" [38] FINISHED WALL 2-14" DIA [Ø57] BC THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE 1-1/4" DIA (Ø32) GRAB BAR SERIES WITH FLANGES FOR EXPOSED MOUNTING MODEL №: 3400 ISSUED: 01/87 REVISED: 6 Dec 2012 SPECIFICATION Grab Bar with Flanges for Exposed Mounting shall be type 304 stainless steel alloy 18-8. Tubing shall be 1-1/4" diameter (Ø32) x 18 gauge [0.048"] (1.2). Flange shall be 11 gauge 1/8" (3) thick and shall be Heliarc welded to tubing with a continuous concealed bead. Flanges shall have three (3) countersunk 9/32" diameter (Ø7) holes to accommodate 1/4" diameter [Ø6] pan head or № 10 self-tapping flat head or oval head mounting screws (not provided). All exposed surfaces shall have a satin finish and shall be protected during shipment with a plastic bag. For optional non-slip surface add suffix –P (peened). 1-1/4" Diameter (Ø32) Grab bar with Flanges for Exposed Mounting shall be Series № 3400 of American Specialties, Inc., 441 Saw Mill River Road, Yonkers, New York 10701- 4913 STRENGTH ASI Grab Bars are designed to meet and exceed ADA requirements as published in CABO/ANSI A117.1 and 2010 ADA Accessibility Standards. Mounting to the wall is a critical part of the system to meet this require- ment. To withstand the shear, tension or pullout, and torsion loads generated by the maximum loading, the fas- tener system must be adequately sized. INSTALLATION Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using three (3) № 10 self-tapping flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange. Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing. For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33" (840) minimum above finished floor (AFF) to 36" (915) maxi- mum AFF. Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series). 10859 X10859 5/21/2018 AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE GRAB BAR CONFIGURATIONS (PG 1 OF 3) MODEL №: GRABBAR CONFIG ISSUED: 09/96 REVISED: 6 Dec 2012 SCHEDULE QTY. DIM. A QTY. DIM. A 12" [305] 36" [914] 18" [457] 42" [1067] 24" [610] 48" [1219] 30" [762] SCHEDULE QTY. DIM. A 52" [1321] 54" [1372] 60" [1524] 72" [1829] TYPE -01 TYPE -02 TYPE -04 TYPE -15 SCHEDULE QTY. HAND LH RH LH SHOWN RH OPPOSITE MODEL № MUST SPECIFY -LH OR -RH 33" [838] 30" [762] 3" [76] PROJECTION BELOW FINISHED FLOOR CONTRACTOR TO PROVIDE PROPER SLEEVE IN FLOOR X 3" LONG TO ACCEPT BAR OD SPECIFIED. 28" [711] 32" [813] 18" [406] 90° 1-1/2" [38] ALL DIMS INCH [MM] A 10859 5/21/2018 AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com 9 32" DIA [Ø7] HOLES WITH .40" DIA [Ø10.2] X 82° COUNTERSINK TO ACCOMMODATE #10 (M5) FLAT HEAD SCREWS OR 1/4" (M6) PAN HEAD SCREWS 120° 18" [3] 3" DIA [Ø76] PEENED OPTION NOTE: ALL DIMS INCH [MM] 1-14" DIA [Ø32]1-12" [38] FINISHED WALL 2-14" DIA [Ø57] BC THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE 1-1/4" DIA (Ø32) GRAB BAR SERIES WITH FLANGES FOR EXPOSED MOUNTING MODEL №: 3400 ISSUED: 01/87 REVISED: 6 Dec 2012 SPECIFICATION Grab Bar with Flanges for Exposed Mounting shall be type 304 stainless steel alloy 18-8. Tubing shall be 1-1/4" diameter (Ø32) x 18 gauge [0.048"] (1.2). Flange shall be 11 gauge 1/8" (3) thick and shall be Heliarc welded to tubing with a continuous concealed bead. Flanges shall have three (3) countersunk 9/32" diameter (Ø7) holes to accommodate 1/4" diameter [Ø6] pan head or № 10 self-tapping flat head or oval head mounting screws (not provided). All exposed surfaces shall have a satin finish and shall be protected during shipment with a plastic bag. For optional non-slip surface add suffix –P (peened). 1-1/4" Diameter (Ø32) Grab bar with Flanges for Exposed Mounting shall be Series № 3400 of American Specialties, Inc., 441 Saw Mill River Road, Yonkers, New York 10701- 4913 STRENGTH ASI Grab Bars are designed to meet and exceed ADA requirements as published in CABO/ANSI A117.1 and 2010 ADA Accessibility Standards. Mounting to the wall is a critical part of the system to meet this require- ment. To withstand the shear, tension or pullout, and torsion loads generated by the maximum loading, the fas- tener system must be adequately sized. INSTALLATION Use grab bar as template to mark mounting holes locations and pre-drill holes. Install bar using three (3) № 10 self-tapping flat head or oval head screws (by others) or other fastener system (by others) to suit conditions for each flange. Appropriate anchoring and backing must be provided in accordance with local building codes or as specified on Architects Plans prior to wall finishing. For compliance with 2010 ADA Accessibility Standards install unit so that the top of the grab bar is 33" (840) minimum above finished floor (AFF) to 36" (915) maxi- mum AFF. Anchors are available from ASI and must be specified separately for each grab bar style scheduled (see 3900 series). 10862 X10862 5/21/2018 AMERICAN SPECIALTIES, INC. 441 Saw Mill River Road, NY 10701 (914) 476.9000 • (914) 476.0688 www.americanspecialties.com THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE GRAB BAR CONFIGURATIONS (PG 1 OF 3) MODEL №: GRABBAR CONFIG ISSUED: 09/96 REVISED: 6 Dec 2012 SCHEDULE QTY. DIM. A QTY. DIM. A 12" [305] 36" [914] 18" [457] 42" [1067] 24" [610] 48" [1219] 30" [762] SCHEDULE QTY. DIM. A 52" [1321] 54" [1372] 60" [1524] 72" [1829] TYPE -01 TYPE -02 TYPE -04 TYPE -15 SCHEDULE QTY. HAND LH RH LH SHOWN RH OPPOSITE MODEL № MUST SPECIFY -LH OR -RH 33" [838] 30" [762] 3" [76] PROJECTION BELOW FINISHED FLOOR CONTRACTOR TO PROVIDE PROPER SLEEVE IN FLOOR X 3" LONG TO ACCEPT BAR OD SPECIFIED. 28" [711] 32" [813] 18" [406] 90° 1-1/2" [38] ALL DIMS INCH [MM] A 10862 5/21/2018 The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 5/02/12 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2012 by Gamco Commercial Restroom Accessories, A Division of Bobrick. 8-1/4" 210mm 4-3/4"121mm 3" 76mm 7/8" 22mm Finish Face of Wall Average Mounting Height Off Floor44" 1118mmConstruCtion: Stainless steel tank-type soap dispensers have 40-fl oz. (1.2-L) capacity. Units are easily filled from top through locked opening. Satin-finished 22-gauge (.759mm) tanks are welded to stainless steel backs. Unit has concealed backplate and sight level indicator. Valve is black molded plastic push button with antibacterial-soap-resistant plastic cylinder and stainless steel spring. CapaCity: 40-fl oz. (1.2-L) of liquid lotion soaps, synthetic detergents and antiseptic solutions. Non-removable filler cap at top of unit is keyed to resist vandalism. instaLLation: Mount wallplate flat side against wall surface with 3- #7 x 3/4" (19mm) panhead zinc plated steel screws provided. Unlock filler cap. Back off machine screw which goes through back panel of unit. Slip dispenser over wall plate and tighten machine screw until secure. overaLL Dimensions: 8-1/4" W x 4-3/4" H x 3" D (210 x 121 x 76mm) valve projects 7/8" (22mm). aDa GuiDe: Mounting location for push button dispensers are 44" (1118mm) maximum above the finish floor. Push buttons and pistons should be operable with one hand and without tight grasping, pinching, or twisting of the wrist. Activation of soap valves should not require more than 5 pounds of force when unit is completely filled. notes: Wood blocking is preferable behind all wall surfaces. If wood blocking is not available, the following fasteners are suggested: Tile/Masonry - Plastic or lead anchors Plaster/Drywall - Toggle bolts Surface-Mounted Horizontal Tank-Type Soap Dispenser with All-Purpose Valve shall be Model G-58AP of GAMCO Commercial Restroom Accessories, A Division of Bobrick, One Gamco Place, Durant, OK surfaCe-mounteDhorizontaL tank-typesoap Dispenserwith aLL-purpose vaLve G-58ap Date: Project Name: X10947 5/21/2018 Georgia-Pacific Professional 133 Peachtree NE Atlanta, GA 30303 1-866-HELLO GP (435-5647) | www.gppro.com printed on 3/10/2010 mmkaye@gapac.com GP® Combination C-Fold/ Multifold Paper Towel Dispenser Combination C-Fold / multifold / BigFold® towel dispenser couples affordability with versatility for cost-conscious customers. Item Description: This durable and versatile plastic towel dispenser holds up to 400 C-Fold, 600 multifold, 500 senior multifold, or one package of BigFold® towels to provide a cost-effective solution for washroom towel dispensing. This attractive see-through grey color complements any decor, and the covered key-lock design protects against waste and pilferage while making refilling towels quick and easy. Features & Benefits: »Durable plastic construction »Holds up to 400 C-Fold, 600 multifold, or one pack BigFold® paper towels »Offers an economical and versatile approach to towel dispensing Product Details Brand Owner Georgia-Pacific Brand GP® MFG Item#56650/01 Design Translucent Smoke UPC UCC-12 073310566504 Each Per Ship Unit 1 Each Items Per Each 0 Each Case Total 1 Each Dispenser (WxDxH)11.000" x 5.250'' x 15.400" UNSPSC 47131701 Replaces Item 59501 Buy Multiple 1 EA Case Shipping Info GTIN 10073310566501 Case Gross Weight 3.140 lbs Case Net Weight 2.220 lbs Case Dimensions 11.125" x 13.625" x 5.688" Case Volume 0.544 CFT Unit Shipping Info Ti-Qty/Layer 10 High-Layers/Unit 8 Unit Qty 80 Unit Dimensions (LxWxH) 48.000" x 39.000" x 48.000" 0 73310 56650 4 SKU: 375374 TAG: M056 DESCRIPTION: Dispenser, Full Size MANUFACTURER: MODEL NUMBER: Georgia-Pacific 56650/01 X10977 5/21/2018 102225/21/2018 IS103446 - 01/09/075/21/2018 104165/21/2018 104625/21/2018 The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 1/10/14 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2014 by Gamco Commercial Restroom Accessories, A Division of Bobrick. Finish Face of Wall S 1-5/8'' 41mm 2'' 51mm Recommended Mounting Height Off Floor72'' 1830mm24'' 610mm 1/2'' 13mm specifications: Units fabricated of 20-gauge (1mm) type 304 stainless steel with exposed surfaces having a satin-finish. Mop holder molded with serrated rubber cam holders and spring loaded to insure maximum gripping ability. Holders accommodate mops and brooms from 3/4" to 1-1/4" (19 to 32mm) in diameter. oVeRaLL DiMensions: 2" H x 1/2" D x 24" L (51 x 13 x 610mm) Low Profile Mop Strip shall be Model__________________ (insert model number) of Gamco Commercial Restroom Accessories, A Division of Bobrick, One Gamco Place, Durant, OK Low pRofiLe Mop stRip Ms-1a 10698 5/21/2018 135785/21/2018 Starbucks: Water Filtration RacksDate: 5.7.12Includes:• Specification Sheets for 18x24 & 16x16 approved sizes• Assembly Instructions• Skid quantities & shipping informationSPG International, LLC11230 Harland Drive NECovington, GA 30014877.503.4SPG www.spgusa.comUpdated: 5.7.12Michael D. Pottermichael.potter@spgusa.com * 404.823.3934138345/21/2018 5/21/2018 5/21/2018 ASSEMBLY INSTRUCTIONS AATB1616-8 & AATB1824-8 STEP 1: UNBOX SHELF AND (4) LEGS. WITH 3/16TH ALLEN WRENCH LOOSEN SCREWS UNTIL CLEAR OF SHELF SOCKET. THE WIDE SIDE OF T- BAR IS THE TOP SIDE OF SHELF. STEP 2: INSERT LEG TO DESIRED HEIGHT AND FIRMLY TIGHTEN SET SCREW. IN MOST CASES THE TOP OF THE PLASTIC CAP SHOULD BE SHOWING STEP 3: REPEAT BOTH STEPS 1 AND 2 ON ALL FOUR CORNERS OF UNIT. LEGS CAN BE ADJUSTED AS NEEDED FOR UNLEVEL FLOORS. SPG International, LLC 11230 Harland Drive NE Covington, GA 30014 877.503.4SPG www.spgusa.com 5/21/2018 53 1/2"Height48"Length40"WidthTOLERANCES UNLESS OTHERWISE SHOWN:DECIMALS: .XX=+/-.03, .XXX=+/-.015ANGULAR SQUARENESS: +/- 1/2 DEGREESFRACTIONS: +/-1/16"THIS SHEET AND THE PRODUCTS CONTAINED THEREIN ARE THE EXCLUSIVE PROPERTY OF: STORAGE PRODUCTS GROUP INTERNATIONAL, LLC.ANY PERSON ACCEPTING THIS SHEET AND/OR INFORMATION AGREES TO MAKE NO DISCLOSURE, USE OR DUPLICATION THEREOF EXCEPT ASAUTHORIZED BY SPG INTERNATIONAL LLC. AND TO RETURN THIS SHEET ON REQUEST. COPYRIGHT (C) 2011 STORAGE PRODUCTS GROUP.Skid will hold 84 Units ofeither 18x24 or 16x16 sizes.Total weight w/ Pallet for 16x16 units: 649 lbsTotal weight w/ Pallet for 18x24 units: 796 lbsSkid SkidPlan View5/21/2018 156995/21/2018 GENERAL TOLERENCESIN ACCORDANCE WITHISO 2768-M 5.5" X 9.5" CUT OUT 13 2X 10 9 4X 1 8 7 2X 12 2X 11 14 3X 2 2X 3 4X 33.8 858 15.7 398 153X 18.55 4719.75 248 7.63 194 3X 27.1 689 40.50 1029 9.75 248 6 2X REVISIONS ZONE REV.DESCRIPTION BY DATE ECO / NPR 01 CUSTOMER APPROVAL JH 1/6/2016 9407 02 CUSTOMER APPROVAL, REV #2 JH 3/4/2016 9407 ITEM NO.QTY.PART NO.DESCRIPTION DWG. NO. BILL OF MATERIALS 15 3 TBD NGFC SHELF BRACKET SHORT, LH K00512_P04 14 3 TBD NGFC SHELF BRACKET SHORT, RH K00512_P03 13 2 TBD NGFC SHELF BRACKET, LH TOP K00512_P02 12 2 TBD NGFC SHELF BRACKET, RH TOP K00512_P01 11 1 TBD 9.75" X 14.25" POLY SHELF CUT K00512_P06 10 1 TBD 14.25" x 40.50" POLY TOP, BLACK K00512_P07 9 4 TBD 9.75" X 14.25" POLY SHELF POLY BLACK K00512_P05 8 1 4H7122 DOUBLE RUNNER WELDMENT, NGFC K00512_A03 7 2 4H7121 SIDE RUNNER WELDMENT, NGFC K00512_A02 6 2 4H7124 TRAY GUARD ASSEMBLY, NGFC K00512_A05 5 8 007-0042 5/16"-18 NYLON INSERT HEX LOCKNUT_STD HW0101_P01 4 12 TBD 5/16"-18 X 1 5/8" HEX HEAD CAP SCREW_GRADE 2 HW0001_P01 3 4 4H7123 CROSSMEMBER, NGFC K00512_A04 2 2 TBD SPLASH GUARD PANEL K00512_P08 1 4 CM3MB 3" SWIVEL POLYURETHANE CASTER W/ BRAKE 100810_A01 4H7120Part No. SHEET 1 of 1 Rev. 1/6/2016 JH Material: APRD 918-3/BK/KD/MOD Drawn By: AS NOTED Finish:AS SPECIFED 02 NEXT GEN FOOD CART, 2 TIER RACK Weight: 11230 Harland DriveCovington, Georgia 30014PH: 1-800-810-9080www.spgusa.com PROPRIETARY NOTICE: This sheet contains confidential, proprietary information of Storage Product Group International LLC. Any person accepting this sheet and/or information agrees to make no disclosure, use or duplication thereof except as authorized by SPG to return this sheet on request. Copyright © 2010 Storage Product Group International. All rights reserved. T:\ENGINEERING\PROJECTS\9400 - 9499\9407- Next Gen Food Card\SWCAD\New\Narrow_Version_1\ K00512_A01 4H7120 NTS Scale: TBD Sketch No. Approved By: TBD Date: Volume: K00512_S01 Description: DIMENSIONS IN ( ) ARE REFERENCE.DIMENSIONS IN [ ] ARE MILLIMETERS, ALL OTHER DIMENSIONS ARE INCHES. NEXT GEN FOOD CART, 2 TIER RACK cu ft. lbs. 17255 5/21/2018 Model# 4H7120 Mobile Pastry Cart Assembly Instructions For Questions, please call 877.503.4774 SPG International, 11230 Harland Drive NE, Covington, GA 30014 Parts list: Shelf Brackets 6 total – Lower side shelf brackets 4 total – Upper side shelf brackets (3-left hand 3- right hand) (2-Left hand 2 right hand) Required Tools: Standard Slot Screwdriver ½” Wrench (2 included) Included Hardware: Fasteners listed below Instruction Sheet Included Fasteners: 24 ea - Euro Screws 4 ea – Sheet metal screws 12 ea – 5/16” x 1 5/8” bolt 8 ea – 5/16” nylon lock nuts 17255 5/21/2018 Aluminum parts 1 ea – Side Pan Tray assembly – With side shelf holes 1 ea – Side Pan Tray assembly – Without side shelf holes 1 ea – Middle pan tray assembly 4 ea – Cross Connector Tubes 2 ea – Tray Guards 4 ea – Casters Polymer Parts 1 ea – 14” x 41” Poly top 3 ea – 14” x 10” Poly side shelves 1 ea – 14” x 10 Poly side shelf with cutout 2 ea – 1/8” Poly Side Panels 17255 5/21/2018 TOP Sides Shelves Pastry Cart Assembly Instructions 17255 5/21/2018 ASSEMBLY STEPS 1. Place two Cross Connector Tubes on floor approximately 13” apart. NOTE: Flush side of tube and square collar should be on the floor. 2. Place top end of Side Pan Tray assembly into the cross connector tube assembly collars. (Top of assembly has plastic caps in tube) Slide rails should face in towards Cross Tube. 3. Insert 5/16” x 1 5/8” bolt through aligned holes in collars and tube from the outside of collar towards the middle of the assembly and thread lock nut onto both bolts 17255 5/21/2018 4.Repeat steps 2 and 3 on opposite end using the 2nd side pan tray assembly. 5.Place cross tubes 3 & 4 onto both side pan tray assemblies with the flush side of the Cross Tube up. 17255 5/21/2018 6. Place the casters into the square tubes with the cross member in place with holes in caster stem facing the same direction as holes in side panel tube. Align holes in cross tube collar, caster stem, and pan tray side. Insert 5/16” x 1 5/8” bolt from the outside of collar towards the middle of the side assembly and hand tighten nylon insert lock nut onto bolt. 7. Place Middle Pan Tray assembly between cross tubes and align threaded inserts with thru holes in the center of the Cross Tube assembly 8. Insert 5/16 x 1 5/8” bolt into insert and hand tighten. 17255 5/21/2018 9. Tighten all bolts using hex wrench. 10. Carefully turn assembly over and place the unit on the previously installed casters. Hold Middle Pan Tray section in place to prevent damage. 11. Align the threaded inserts in the Middle Pan tray with through holes in the center of the Cross Tube assembly 12. Insert5/16” x 1 5/8” bolt into insert and tighten. 17255 5/21/2018 13.Insert Poly Side Panels from top between tray runners and square cross tubes on each end. Side panels will rest on caster flanges 14.Place Tray Guard straps on the back of the cart by putting u-channel end of the strap over bottom Cross Tube in the middle of the tray openings. 17255 5/21/2018 15.Slowly place Poly Top onto the cart. The cutouts in the top need to align with a) the bolt heads in the middle of the Cross Tube and b) the Tray Guards. 16.Once in place, attach top to the frame using included Z-brackets in 4 locations using Euro Screws 17.Attach LH and RH lower shelf brackets to side poly side solid shelves using ½” Euro screws. Attach LH and RH upper shelf brackets to one solid shelf and one shelf with cutout using ½” Euro Screws. 18.Attach Upper side shelf brackets/shelves into place using sheet metal screws and predrilled holes in Side Pan Tray vertical tubes. 17255 5/21/2018 19.Attach Lower side shelf assemblies by placing shelf bracket hanger over side panel assembly flat bar. Hook area will fit between side plastic sheet and flat aluminum flat bar in Side Pan Tray vertical tubes. Unit is ready for use. 17255 5/21/2018 KELMAX 4H7120-R Guide d’assemblage du chariot à pâtisserie Starbucks™ TOUT, LÀ OÙ VOUS EN AVEZ BESOIN, ET TOUT À SA PLACE. INSTK00513_A01_C-17255 5/21/2018 KELMAX INSTK00513_A01_C-4H7120-R Coordonnées de SPG Starbucks™ - Directrice de compte de SPG Lisa Gochnour Directrice de compte stratégique 3340 Peachtree Road NE Suite 1250 Atlanta, GA 30326 Téléphone 877.503.4774 x1458 Télécopieur 404.709.1905 Courriel lisa.gochnour@spgusa.com Starbucks™ - Ingénieur de SPG James Knutson Directeur de l’ingénierie 11230 Harland Drive NE Covington, GA 30014 Téléphone 877.503.4774 x1211 Téléphone cellulaire 404.904.4297 Courriel james.knutson@spgusa.com Starbucks™ - Représentant du service à la clientèle de SPG Tammy Jones Service à la clientèle 11230 Harland Drive NE Covington, GA 30014 Téléphone 800.874.0375 x1258 Télécopieur 800.577.2210 Courriel tammy.jones@spgusa.com Starbucks™ - Contact du siège social de SPG Michael Potter Directeur du développement commercial 3340 Peachtree Road NE Suite 1250 Atlanta, GA 30326 Téléphone 877.503.4SPG x1435 Téléphone cellulaire 404.823.3934 Courriel michael.potter@spgusa.com Chariot à pâtisserie mobile Starbucks™ Liste de contacts/ Outils nécessaires et matériaux inclus 1 1-877-503-4SPG (4774) www.spgusa.com OUTILS NÉCESSAIRES 1.Tournevis Philips 2.Clés de ½ po (2 incluses) MATÉRIEL/VIS FOURNIES 1.Fiche d’instructions 2.Vis à tête cylind. de feuille métallique #12 x ¾ po 3.Vis FH Phillips Euro M6, 3-2,2 x 10 mm 4.Vis hexagonale 5/16 po à 18 x 1 ¾ po 5.Contre-écrou à garniture de nylon de 5/16 po -18 6.Équerre en Z PIÈCES EN ALUMINIUM PIÈCES EN POLYMÈRE SUPPORTS À TABLETTES 1.Assemblage du plateau latéral du moule 2.Assemblage du plateau du moule du milieu 3.Traverses tubulaires de raccordement 4.Protecteurs du plateau 5.Roulettes Qté- 2 Qté- 1 Qté- 4 Qté- 2 Qté- 4 1.Haut en poly de 14,25 po x 41 po 2.Étagères latérales en poly de 14,25 po x 10 po 3.Étagère latérale en poly de 14,25 po x 10 po avec encoche 4.Panneaux latéraux en poly de 3/16 po Qté- 1 Qté- 4 Qté- 1 Qté- 2 1.Supports à tablettes inférieures latérales (3- du côté gauche, 3- du côté droit) 3.Supports à tablettes latérales supérieures (2- du côté gauche, 2- du côté droit) Qté- 6 Qté- 4 * Les éléments et les roulettes en polymère sont colorés en bleu pour une identification plus facile dans les instructions écrites. La couleur standard du polymère est le noir. Qté- 8 Qté- 24 Qté- 12 Qté- 8 Qté- 4 17255 5/21/2018 INSTK00513_A01_C- Chariot à pâtisserie mobile Starbucks™ Liste de contacts/ Outils nécessaires et matériaux inclus Chariot à pâtisserie mobile Starbucks™ Liste des pièces 2 Roulettes (4)Assemblage du plateau latéral du moule (2) Avec bande anti-bruit Assemblage du plateau du moule du milieu (1) Avec bande anti-bruit Traverses tubulaires de raccordement (4) Protecteurs du plateau (2) Étagères latérales en poly (4) Étagère latérale en poly avec encoche (1) Haut en poly (1) Panneaux latéraux en poly (2) 17255 5/21/2018 KELMAX INSTK00513_A01_C-4H7120-R Chariot à pâtisserie mobile Starbucks™ Guide d’installation de la bordure d’insonorisation Insérez une extrémité de la section en caoutchouc sur la glissière du plateau, juste après l’intersection entre le rayon et la section droite de la glissière en aluminium. 1. 2.En suivant la glissière, poussez la section en caoutchouc dans celle-ci. 3.Une fois en place, passez la main ou un objet dur le long de la glissière pour s’assurer que la section en caoutchouc est entièrement engagée dans la glissière en aluminium. 17255 5/21/2018 INSTK00513_A01_C- Chariot à pâtisserie mobile Starbucks™ Guide d’installation 4 4.Insérez le boulon de 5/16 po - 18 x 1 ¾ po à travers les trous alignés dans les cols et le tube à partir de l’extérieur du col vers le milieu de l’assemblage et vissez le contre- écrou sur les boulons. Placez l’assemblage du plateau du moule du milieu entre les traverses tubulaires et alignez les inserts taraudés avec les orifices au centre de l’assemblage de la traverse tubulaire. 5. Insérez le boulon de 5/16 po - 18 x 1 ¾ po dans l’insert et serrez à la main. 6. 3 3 4 4 4 4 6 5 17255 5/21/2018 KELMAX INSTK00513_A01_C-4H7120-R Chariot à pâtisserie mobile Starbucks™ Guide d’installation 5 Placez les traverses tubulaires sur les deux assemblages du plateau latéral du moule avec le côté plat de la traverse tubulaire vers le haut. 7. 11.Serrez tous les boulons en utilisant la clé hexagonale. Alignez les inserts taraudés dans le plateau du moule du milieu avec les trous au centre de l’assemblage de la traverse tubulaire. 9. 10.Insérez le boulon de 5/16 po - 18 x 1 ¾ po dans l’insert et serrez à la main. 10 9 Placez les courroies du protecteur du plateau à l’arrière du chariot en mettant l’extrémité de la goulotte en u de la courroie sur la traverse tubulaire du bas au milieu des ouvertures du plateau. 12. 12 8.Insérez le boulon de 5/16 po - 18 x 1 ¾ po à travers les trous alignés dans les cols et le tube à partir de l’extérieur du col vers le milieu de l’assemblage et vissez le contre-écrou sur tous les boulons. 12 8 7 7 17255 5/21/2018 INSTK00513_A01_C- Chariot à pâtisserie mobile Starbucks™ Guide d’installation 6 Insérez les panneaux latéraux en poly à partir du haut entre les glissières du plateau et la barre plane transversale carrée à chaque extrémité. Les panneaux latéraux s’appuieront sur les rebords des roulettes. 13. Placez lentement le haut en poly sur le chariot et glissez les crochets en z fixés sur la barre transversale. Les encoches du haut doivent être alignées avec a) les têtes des boulons au milieu de la traverse tubulaire et b) les protecteurs du plateau. 15. Pré-assemblez 2 crochets en z dans les trous situés à l’extrémité extérieure sur le haut en poly, en utilisant les vis Euro. 14. 14 15 15 15 13 13 17255 5/21/2018 KELMAX INSTK00513_A01_C-4H7120-R Chariot à pâtisserie mobile Starbucks™ Guide d’installation 7 16.Une fois en place, fixez le haut à la structure en utilisant les crochets en z inclus dans les 2 emplacements qui restent en utilisant les vis Euro. 17.Fixez les supports inférieurs LH et RH de l’étagère aux étagères latérales pleines en poly en utilisant les vis Euro. Fixez les supports supérieurs LH et RH de l’étagère à une étagère pleine avec encoche en utilisant les vis Euro. Fixez les crochets/étagères de l’étagère latérale supérieure en utilisant les vis à tête cylindrique de feuille métallique #12 x ¾ po dans les trous percés à l’avance dans les tubes verticaux du plateau latéral du moule. 18. REMARQUE : Vue du dessous REMARQUE : Vue du dessous 16 16 17 17 17 17 18 17255 5/21/2018 INSTK00513_A01_C- Chariot à pâtisserie mobile Starbucks™ Guide d’installation 8 Fixez les assemblages de l’étagère latérale inférieure en plaçant le crochet du support de l’étagère sur la barre plate de l’assemblage du panneau latéral. La zone du crochet s’insérera entre la feuille de plastique latérale et la barre plate en aluminium dans les tubes verticaux du plateau latéral du moule. 19. 20. 19 L’assemblage est complété! Le chariot à pâtisserie mobile est prêt à utiliser ! 17255 5/21/2018 KELMAX 4H7120-R INSTK00513_A01_C- Maximiser l’efficacité, améliorer la performance, obtenir plus de vos employés et de votre investissement—c’est ce que vous devez faire tous les jours pour que votre entreprise réussisse mieux et soit plus rentable. Et c’est ce que SPG vous aide à réaliser par le biais de notre gamme étendue d’équipement novateur de service alimentaire. Chez SPG, notre équipement est conçu de façon ergonomique pour diminuer le temps, les mouvements et les efforts de votre personnel—tout en maximisant l’efficacité de chaque pouce de votre espace disponible. Nous utilisons les meilleurs matériaux pour le travail et la fabrication avec des tolérances strictes afin de nous assurer que notre équipement offre un rendement et une valeur durables. En tant qu’entreprise mondiale, nous fabriquons des gammes de produits d’entreposage de qualité comme ISS, Kelmax, Freestyle et bien d’autres en Amérique du Nord et dans le Pacifique. Par conséquent, nos produits sont livrés chaque jour à des entreprises du monde entier…et chaque jour nous continuons de les livrer avec la promesse d’assurer leur succès et rentabilité constants. Soyez plus. Faites-en plus. www.spgusa.com ©2016 SPG International, LLC. Non seulement nous établissons des normes élevées, mais nous les dépassons.Guide d’assemblage du chariot à pâtisserie Starbucks™ ATTENDEZ-EN PLUS 17255 5/21/2018 172645/21/2018 SPG KDA RACK ASSEMBLY INSTRUCTIONS            17264 5/21/2018 Parts List:    Assembly Tools Required (Provided)                                                                             X 2   17264 5/21/2018 Step 1: Neatly layout the contents of the box on a work surface. Confirm that all required  parts are present.   Step 2:  SET THE ASSEMBLY TOOLS TO SIDE.   Tools are not required until (step 13).   Step 3: Turn frames upside down, so that the open post is at the top.   (Note: The top of the frame has plastic caps, while the bottom is open.)   Step 4: Take the two of the cross bars and slip over the bottom posts of the frame.  Making  sure the holes line up.   (Note: Cross bars are designed to fit in any direction but should you encounter binding, flip  the cross bar until the fit is proper.)  Step 5: Insert a caster into each bottom post. Make sure the hole in the caster lines up with  the holes in each of the bottom posts and cross bars.  Step 6: Insert a bolt through the holes in the bottom post, cross bar and caster and attach a  lock nut by hand. DO NOT USE THE ASSEMBLY TOOL AT THIS TIME.                 Bottom of Cart (Note: The top of  the frame has plastic caps, while  the bottom is open.)  17264 5/21/2018 Step 7: Turn the cart over. (Casters should now touch the ground)  Step 8: Take the two of the cross bars and slip over the top posts of the frame.  Making sure  the holes line up.  Step 9: Insert a bolt through each top post and cross bar and attach a lock nut by hand. DO  NOT USE THE ASSEMBLY TOOL AT THIS TIME.      Step 10:  Insert Middle Cross Bars. Line these up with the holes in the center of cart.   Step 11: Insert (4) Bolts in the (4) Channel Braces     Step 12: Place a Bolt and Channel Brace into each of side of the Middle Cross Bars and tighten  by hand. DO NOT USE THE ASSEMBLY TOOL AT THIS TIME.      Middle of cart.   Top of Cart (Note: The top of the  frame has plastic caps.  17264 5/21/2018 Step 13:  Gather the assembly tools. You may now use the tools. Tighten each of the (12)  Bolts using one wrench to hold the nut and the other to turn the bolt. Turn the wrench  clockwise to tighten.     Step 14: You’re done. Put the cart into service.     Assembly Tools  17264 5/21/2018 SPG KDA RACK ASSEMBLY INSTRUCTIONS INSTRUCTIONS D’ASSEMBLAGE DE L’ÉTAGÈRE KDA DE SPG 17264 5/21/2018 Parts List: Liste des pièces : DANS LA BOÎTE : QTÉ 2 – ASSEMBLAGE DE LA STRUCTURE QTY 4 – TOP & BOTTOM CROSS BARS QTY 2 – CENTER CROSS BARS QTY 2 – SWIVEL STEM CASTERS QTY 2 – SWIVEL STEM CASTERS WITH BRAKE QTÉ 1 – SAC DE MATÉRIEL QTÉ 8 – ÉCROUS NYLOCK QTÉ 12 – BOULONS X 2 IN THE BOX : QTY 2 – FRAME ASSEMBLIES QTÉ 4 – BARRES TRANSVERSALES DU HAUT ET DU BAS QTÉ 2 – BARRES TRANSVERSALES DU CENTRE QTÉ 2 – ROULETTES À TIGES PIVOTANTES QTÉ 2 – ROULETTES À TIGES PIVOTANTES AVEC FREIN QTY 1 – HARDWARE BAG QTY 8 – NYLOCK NUTS QTY 12 – BOLTS Outils d’assemblage requis (Inclus) Assembly Tools Required (Included) 17264 5/21/2018 Step 1: Neatly layout the contents of the box on a work surface. Confirm that all required parts are present. Étape 1 : Disposez proprement le contenu de la boîte sur une surface de travail. Assurez-vous que toutes les pièces nécessaires sont présentes. Step 2: SET THE ASSEMBLY TOOLS TO SIDE. Tools are not required until (step 13) Étape 2 : METTEZ DE CÔTÉ LES OUTILS D’ASSEMBLAGE. Les outils ne sont pas nécessaires jusqu’à l’étape 13. Step 3: Turn frames upside down, so that the open post is at the top. Étape 3 : Mettez la structure à l’envers, pour que le Poteau ouvert soit au-dessus. (Note: The top of the frame has plastic caps, while the bottom is open.) (Remarque : Le haut de la structure possède des bouchons de plastique, tandis que le bas est ouvert.) Step 4: Take the two of the cross bars and slip over the bottom posts of the frame. Making sure the holes line up. Étape 4 : Prenez les deux barres transversales et glissez-les au-dessus des poteaux du bas de la structure. Assurez-vous que les poteaux soient alignés. (Note: Cross bars are designed to fit in any direction but should you encounter binding, flip the cross bar until the fit is proper.) (Remarque : Les barres transversales sont conçues pour aller dans chaque direction mais s’il y a une contrainte, retournez la barre transversale jusqu’à ce que l’ajustement soit adéquat.) Step 5: Insert a caster into each bottom post. Make sure the hole in the caster lines up with the holes in each of the bottom posts and cross bars. Étape 5 : Insérez une roulette dans chaque poteau du bas. Assurez-vous que le trou dans la roulette s’ajuste aux trous de chacun des poteaux du bas et barres transversales. Step 6: Insert a bolt through the holes in the bottom post, cross bar and caster and attach a lock nut by hand. DO NOT USE THE ASSEMBLY TOOL AT THIS TIME. Étape 6 : Insérez un boulon à travers les trous dans le poteau du bas, la barre transversale et la roulette et fixez un écrou de blocage à la main. N’UTILISEZ PAS D’OUTIL D’ASSEMBLAGE À CE MOMENT. 17264 5/21/2018 Step 7: Turn the cart over. (Casters should now touch the ground) Étape 7 : Retournez le chariot. (Les roulettes devraient maintenant toucher le sol) Step 8: Take the two of the cross bars and slip over the top posts of the frame. Making sure the holes line up. Étape 8 : Prenez deux barres latérales et glissez-les sur les poteaux du haut de la structure. Assurez-vous que les trous soient alignés. Step 9: Insert a bolt through each top post and cross bar and attach a lock nut by hand. DO NOT USE THE ASSEMBLY TOOL AT THIS TIME. Étape 9 : Insérez un boulon à travers chaque poteau du haut et barre transversale et fixez un écrou de blocage à la main. N’UTILISEZ PAS D’OUTIL D’ASSEMBLAGE À CE MOMENT. BRAKE FREIN BRAKE FREIN Bottom of Cart (Note: The top of the frame has plastic caps, while the bottom is open.) Bas du chariot (Remarque : Le haut de la structure possède des bouchons de plastique, tandis que le bas est ouvert.) Top of Cart (Note: The top of the frame has plastic caps. Haut du chariot (Remarque : Le haut de la structure possède des bouchons de plastique.) 17264 5/21/2018 Step 10: Insert Middle Cross Bars. Line these up with the holes in the center of cart. Étape 10 : Insérez les barres transversales des barres transversales du milieu. Alignez-les avec les trous au centre du chariot. Step 11: Insert (4) Bolts in the (4) Channel Braces Étape 11 : Insérez (4) boulons dans les (4) renforts Step 12: Place a Bolt and Channel Brace into each of side of the Middle Cross Bars and tighten by hand. DO NOT USE THE ASSEMBLY TOOL AT THIS TIME. Étape 12 : Placez un boulon et un renfort dans chaque côté des barres transversales du milieu et serrez à la main. N’UTILISEZ PAS D’OUTIL D’ASSEMBLAGE À CE MOMENT. Step 13: Gather the assembly tools. You may now use the tools. Tighten each of the (12) bolts using one wrench to hold the nut and the other to turn the bolt. Turn the wrench clockwise to tighten. Do not over tighten. Étape 13 : Rassemblez les outils d’assemblage. Vous pouvez maintenant utiliser les outils. Serrez chacun des (12) boulons en utilisant une clé pour retenir l’écrou et l’autre pour tourner le boulon. Tournez la clé dans le sens des aiguilles d’une montre pour serrer. Ne pas trop serrer. Middle of cart. Milieu du chariot. 17264 5/21/2018 Step 14: You’re done. Put the cart into service. Étape 14 : Vous avez terminé. Utilisez le chariot. 17264 5/21/2018 GENERAL TOLERENCESIN ACCORDANCE WITHISO 2768-M638.1825.1357.661464.4754321REVISIONSZONE REV.DESCRIPTIONBY DATE ECO / NPR01 FOR CUSTOMER REVIEW ONLY AGR 8/10/2016 9431ITEM NO. QTY. PART NO.DESCRIPTIONDWG. NO.BILL OF MATERIALS5 4 LU24* 24" UNIVERSAL SHELF LEDGE102709_A014 2 CM5PB 5" SWIVEL POLYURETHANE CASTER W/ BRAKE 100810_A013 2 CM5P 5" SWIVEL POLYURETHANE CASTER 100810_A012 4 2424* 24"X24" ISS WIRE SHELF101151_A011 4 P48N* 48" ISS POST FOR CASTER (NO FOOT)100113_A02 #39 #3 #21 #45103.1216.06407.924.0625.06636.57NONEScale:TBDSketch No.Approved By:TBDDate:Volume:Description:DIMENSIONS IN ( ) ARE REFERENCE.TBDPart No.SHEET 1 of 1Rev.08/10/2016AGRMaterial:Group International. All rights PH: 1-800-810-9080Covington, Georgia 30014Drawn By:AS NOTED24"X24" MINI STORAGE CARTDIMENSIONS IN [ ] ARE MILLIMETERS, ALL OTHER DIMENSIONS ARE INCHES.WITH UNIVERSAL LEDGEScu ft. TBD MINI STORAGE RACKT:\ENGINEERING\PROJECTS\9400 - 9499\9431 - Mini Storage Rack\SW_CAD\reserved.PROPRIETARY NOTICE:www.spgusa.comFinish:AS SPECIFIED0124"X24" MINI STORAGE CARTWeight:TBD11230 Harland DriveThis sheet contains confidential, proprietary information of Storage Product Group International LLC. Any person accepting this sheet and/or information agrees to make no disclosure, use or duplication thereof except as authorized by SPG to return this sheet on request. Copyright © 2010 Storage Product lbs.176395/21/2018 IN ACCORDANCE WITHGENERAL TOLERENCESISO 2768-MREVISIONSZONE REV.DESCRIPTIONBY DATE ECO / NPR01FOR CUSTOMER APPROVALAS 1/20/2017 N/AITEM NO. QTY. PART NO.DESCRIPTIONDWG. NO.BILL OF MATERIALS5 1 CWB-4 4 -CYLINDER WALL MOUNT BRACKET 104506_A014 4 WCP* WALL ANGLE BRACKET_ 1" HOLE 100044_P013 2 FR3* 18" ONE SIDED FRAME102716_A012 2 PS74* 74" SPLIT POST_ SET OF 2 POSTS 101125_A011 4 1836* 18"X36" ISS WIRE SHELF101151_A0119.19487104854_A01Description:DIMENSIONS IN ( ) ARE REFERENCE.WST1823CPart No.SHEET 1 of 1Rev.1/20/2017ASMaterial:FOR 4 CARBONATION TANKSDrawn By:AS NOTEDFinish:PLATING PLUS01DIMENSIONS IN [ ] ARE MILLIMETERS, ALL OTHER DIMENSIONS ARE INCHES.Group International. All rights PH: 1-800-810-9080Weight:11230 Harland Drivecu ft.18"X36" CARBONATOR PLATFORM18"X36" CARBONATOR PLATFORMCovington, Georgia 30014Volume:Date:TBDApproved By:Sketch No.TBDwww.spgusa.comPROPRIETARY NOTICE:reserved.T:\ENG-SW\CURRENT VERSIONS_SPG\ASSEMBLIES\ASSY_SKETCHES\104854_A01 WST1823C NTSScale:This sheet contains confidential, proprietary information of Storage Product Group International LLC. Any person accepting this sheet and/or information agrees to make no disclosure, use or duplication thereof except as authorized by SPG to return this sheet on request. Copyright © 2010 Storage Product lbs. #37 #7 #60 #55 #7436.10917189974.7735.8391031245181595/21/2018