The URL can be used to link to this page

Home My WebLink AboutFile Documents.525 E Cooper Ave.0061.2018.ACBK0061-2018-ACBK_BuildingComment1 Subject: PlanCheck Page Label: 1 Author: justinh File Name: ComCheck.pdf Provide cutsheets on all light fixtures that give maximum fixture wattage (not bulb) and NRTL listing. ComCheck.pdf (4) Subject: PlanCheck Page Label: 1 Author: justinh File Name: ComCheck.pdf This sf is much more than the area that I measure for what you are showing on your lighting plan. If you are using the sf of the entire restaurant you must show all existing lighting in the entire space and include it on your ComCheck. Please reduce this number to only account for the dining space where lighting is being altered. Any existing lighting to remain after this remodel in that area should also be included on your ComCheck. Subject: PlanCheck Page Label: 1 Author: justinh File Name: ComCheck.pdf You need to be using the space by space method as you are not doing a ComCheck for the entire building. Please revise, this watt/sf should only be .89 per IECC table C405.4.2(2). Subject: PlanCheck Page Label: 1 Author: justinh File Name: ComCheck.pdf I agree with the fixture count for fixture A, but am unsure regarding the pendant and sconce. I count 10 of fixture C on the lighting plan which appears to be a sconce, but you show 20 on this report. I do not see 10 pendant lights shown on your lighting plan and I do not see where the 6 lights marked B are shown on this report. Please clarify and revise the ComCheck and lighting plan as needed. Signature Date E Cooper.cck R Provide cutsheets on all light fixtures that give maximum fixture wattage (not bulb) and NRTL listing. Interior Lighting Compliance Certifica Project Title: 2015 IECC Project Type:Alteration Construction Site: 525 E Cooper Ave Aspen, CO 81611 Owner/Agent: Aspen Grove Associates LLP 51027 Highway 6 & 24 Suite 100 Glenwood Springs, CO 81611 970.945.1200 Designer/Contractor: Michael Edinger A.D.C. 1331 East Sopris Creek Roa Basalt, CO 81621 719.331.9211 michael@aliusdc.com Project Information Energy Code: 525 E Cooper Ave Allowed Interior Lighting Power A Area Category B Floor Area (ft2) C Allowed Watts / ft2 A 1-Existing Rest. (Dining: Family)2722 0 .95 Total Allowed Watts = Proposed Interior Lighting Power D Fixtu Watt A Fixture ID : Description / Lamp / Wattage Per Lamp / Ballast B Lamps/ Fixture C # of Fixtures This sf is much more than the area that I measure for what you are showing on your lighting plan. If you are using the sf of the entire restaurant you must show all existing lighting in the entire space and include it on your ComCheck. Please reduce this number to only account for the dining space where lighting is being altered. Any existing lighting to remain after this remodel in that area should also be included on your ComCheck. e Associates LLP way 6 & 24 Springs, CO 81611 00 Designer/Contractor: Michael Edinger A.D.C. 1331 East Sopris Creek Road Basalt, CO 81621 719.331.9211 michael@aliusdc.com ve B Floor Area (ft2) C Allowed Watts / ft2 D Allowed Watts (B X C) 2722 0 2586.95 2586Total Allowed Watts = E (C X D) D Fixture Watt. er Lamp / Ballast B Lamps/ Fixture C # of Fixtures You need to be using the space by space method as you are not doing a ComCheck for the entire building. Please revise, this watt/sf should only be .89 per IECC table C405.4.2(2). Proposed Interior Lighting Power A Fixture ID : Description / Lamp / Wattage Per Lamp / Ballast Existing Rest. ( Dining: Family 2722 sq.ft.) LED 1: LED A Lamp 9W: Incandescent 1: PENDANT: Incandescent 40W: Incandescent 2: SCONCE: Incandescent 40W: Interior Lighting Compliance Statement Compliance Statement: The proposed interior lighting alteration project rep building plans, specifications, and other calculations submitted with this per systems have been designed to meet the 2015 IECC requirements in COMch mandatory requirements listed in the Inspection Checklist. Name - Title Signature Interior Lighting PASSES Project Title: Data filename: 525 E Cooper Ave C:\Users\Michael\Desktop\525 E Cooper.cck I agree with the fixture count for fixture A, but am unsure regarding the pendant and sconce. I count 10 of fixture C on the lighting plan which appears to be a sconce, but you show 20 on this report. I do not see 10 pendant lights shown on your lighting plan and I do not see where the 6 lights marked B are shown on this report. Please clarify and revise the ComCheck and lighting plan as needed. I spoke to Alex from LEAX about this at length. We will verify the bulbs match my wattage though I don't feel I should have to compromise the lighting design because the fixture can support a different bulb. We will use the bulbs we spec. Let's discuss. I have adjusted the sq. ft. calculation to only include the area we are affecting. The revised COmCheck is using the space by space method I believe I have all counts accurate and matching on plan and commcheck Subject: PlanCheck Page Label: 3.3 UPPER LEVEL PLAN NEW Author: justinh File Name: Permit Set.pdf Please clarify how this door system stacks and provide cutsheets that show more information. I had assumed that the panels stack over the swinging man door when the sliders are in the open position but this seems to show that the entire system would slide over this portion of wall. Permit Set.pdf (27) Subject: PlanCheck Page Label: 3.3 UPPER LEVEL PLAN NEW Author: justinh File Name: Permit Set.pdf These doors do not comply as egress doors. IBC 1010.1.1 requires egress doors with 2 leaves without a mullion to have at least one leaf be 32" wide. Please revise. Subject: PlanCheck Page Label: 3.4 UPPER LEVEL R.C.P.-EXISTING Author: justinh File Name: Permit Set.pdf If this work is not proposed in the scope of your permit then please remove it from your plans. If you are proposing exterior lighting anywhere with this permit then you must submit an exterior lighting ComCheck. Subject: PlanCheck Page Label: 3.6 UPPER LEVEL FURNITURE PLAN Author: justinh File Name: Permit Set.pdf You are showing 108 seats not counting the bar seating. 5% of your seating is required to be accessible which means that 6 accessible seats distributed throughout the entire space are required. Clearly identify these six seats and demonstrate that they meet ANSI requirements for accessibility. All accessible seating shall be on an accessible route. Subject: PlanCheck Page Label: 3.6 UPPER LEVEL FURNITURE PLAN Author: justinh File Name: Permit Set.pdf This elevation legend does not match what is actually shown on sheet 8.4, please revise so that the numbering corresponds to the correct elevations. 103 EXISTINGCOLUMNS TOREMAIN; TYP. LINE OF EXISTINGMECHANICAL CHASE ABOVEEXISTINGELECTRICALPANEL FLOOR DRAINFLOOR DRAIN EXISTING INSOROLLSHADE SYSTEM OPEN TO BELOW NEW SINGLETRACK SLIDINGDOOR SYSTEMSTACKINGLOCATION NEW MILLWORK WRAP @COLUMN TYP. THROOMS OUTSIDE RK SCOPE TO EAST STAIRWELL DININGROOM203 WOMEN'S 204 SHELVING ABOVERESINVINYLPlease clarify how this door system stacks and provide cutsheets that show more information. I had assumed that the panels stack over the swinging man door when the sliders are in the open position but this seems to show that the entire system would slide over this portion of wall. 101 101 103 102 102 104 43 73/4" 4'-81/2"8'-101/2"103/4"3'-81/4"61/8"2'-2"2'-2"61/8"3'-75/8"31/2"7'-8"EXISTING MONTIGO H38DF TO FLUE CLEARANCE - 16" FROM W 10'-0" FROM CENTERLINE OF C AVENUE, 10'-0" FROM ADJACEN EXISTING WEST STAIRWELL EXISTING ROOFDRAIN & COLUMN EXIST. COORIDOR DIM.TO BE MAINTAINED DININGROOM208 COAT ROOM202 CL W1 EXISTINGCOLUMNS TOREMAIN; TYP. These doors do not comply as egress doors. IBC 1010.1.1 requires egress doors with 2 leaves without a mullion to have at least one leaf be 32" wide. Please revise. DESIGN CORPS ALIUS DESIGN CORPS ALIUS COEAST COOPER24'-7 1/16" WEST STAIRWELL P6 P6 P6P6 P6 P6 P6 FIELD OF LIGHT - LANTERNSTO CREATE ENTRY EXPERIENCE TV AWNINGR+B TO WORK WITH CITY OF ASPEN AND BUILDING OWNER TO GET OUTDOOR LIGHTINGAPPROVED A 4 DININGROOM208 05 BAR209 If this work is notproposed in the scope of your permit then please remove it from your plans. If you areproposing exteriorlighting anywhere with this permit then you must submit an exterior lightingComCheck. DE A You are showing 108 seats not counting the bar seating. 5% of your seating is required to be accessible which means that 6 accessible seats distributed throughout the entire space are required. Clearly identify these six seats and demonstrate that they meet ANSI requirements for accessibility. All accessible seating shall be on an accessible route. DININGROOM 208 28.4 1 4 3 This elevation legend does not match what is actually shown on sheet 8.4, please revise so that the numbering corresponds to the correct elevations. the stacking is clarified on plan sheets and door detail sheets the doors have been changed to 5'-0" wide it is not in the scope and has been eliminated from the drawing set 6 accessible seats are shown irrelevant elevations have been removed and tags coordinated with remaining elevations Subject: PlanCheck Page Label: 3.6 UPPER LEVEL FURNITURE PLAN Author: justinh File Name: Permit Set.pdf 11 bar seats requires 1 accessible space with a companion space. This does not comply as drawn, clear space must be forward facing and pulled into the accessible portion of the bar demonstrating proper knee and toe clearance. Both the required accessible space and the companion space must have the forward facing 30"x48" clear space. Subject: PlanCheck Page Label: 3.6 UPPER LEVEL FURNITURE PLAN Author: justinh File Name: Permit Set.pdf Clearly show the existing doors to remain on all proposed floor plans. Subject: PlanCheck Page Label: 3.6 UPPER LEVEL FURNITURE PLAN Author: justinh File Name: Permit Set.pdf Accessible clear spaces at tables must be drawn forward facing to demonstrate you have the required clearance to sit at a table, parallel clear spaces do not work. The forward facing clear space should also be drawn tucked into the table a minimum of 17" to demonstrate the required knee and toe clearance. Subject: PlanCheck Page Label: 3.6 UPPER LEVEL FURNITURE PLAN Author: justinh File Name: Permit Set.pdf Show a 3' wide accessible route through your tenant space that connects all required exits, the restrooms, and all accessible seating. Required clear spaces at accessible seating cannot overlap into this 3' wide accessible route. Subject: PlanCheck Page Label: 8.1 1/2 " INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf Your detail references have the wrong sheet, these are provided on 7.2, please revise on all elevation sheets.3/64"2'-2 43/64" 30"x48" CLEAR FLOORSPACE DUMB WAITER BAR202 KITCHEN205 BACK BAR COAT ROOM202 W 1&2 8.3 58.18.24 8.11 2 3 X 2 8.2 11 bar seats requires 1 accessible space with a companion space. Thisdoes not comply as drawn, clearspace must be forward facing andpulled into the accessible portion ofthe bar demonstrating proper knee and toe clearance. Both the required accessible space and the companion space must have the forward facing30"x48" clear space. 208 05 3 Clearly show the existing doors to remain on all proposed floor plans.3'-0 33/64"TO EAST STAIRWELL DININGROOM203 MEN'S204 WOMEN'S204 KITCHEN205 DININGROOM203 4 Accessible clearspaces at tables must be drawn forward facing to demonstrateyou have the required clearance to sit at a table, parallel clearspaces do not work. The forward facing clear space should also be drawn tuckedinto the table a minimum of 17" to demonstrate therequired knee and toe clearance. BAR202 BACK BAR Show a 3' wide accessible route through your tenant space that connects all required exits, the restrooms, and all accessible seating. Required clear spaces at accessible seating cannot overlap into this 3' wide accessible route. 6 1/4"47.5 Your detail references have the wrong sheet, these are provided on 7.2, please revise on all elevation sheets. accessible seating has been clarified and shown in accordance with code requirements. See furniture plan the existing doors are shown the required 17" is shown on the furniture plan the accessible route is shown on the furniture plan the tags have been revised to reflect the accurate detail Subject: PlanCheck Page Label: 8.1 1/2 " INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf Egress doors in spaces with occupant loads greater that 50 are required to have compliant panic/fire exit hardware per IBC 1010.1.10, this applies to doors 101, 102 and 103. Provide cutsheets on the hardware and show this on your elevations and schedule. Subject: PlanCheck Page Label: 8.1 1/2 " INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf Egress doors (doors 101, 102, and 103) are required to have a smooth surface on the bottom 10" of the push side per ANSI 404.2.9, provide cutsheets on all swinging egress doors that shows compliance with this requirement. Subject: PlanCheck Page Label: 8.1 1/2 " INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf Please verify that the coat room will be for employee use rather than patrons. If patrons are hanging up their own coats then an additional rack at a max height of 48" must be provided for accessibility. Subject: PlanCheck Page Label: 8.2 1/2" INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf This is not an existing elevation, you are showing the proposed slider door. Please re-title the elevation to accurately depict what you are showing. Subject: PlanCheck Page Label: 8.3 1/2" INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf This detail and page are not included in this set. Provide them or remove the reference. 67.557.5 47.5 FIXED MILLWORKFIXED GLAZINGFIXED GLAZINGFIXED MILLWORK NEW FIXED GLAZING FIXED MILLWORK LLWORK MOLDING BASEG N MOLDING VATION Egress doors in spaces with occupant loads greater that 50 are required to have compliant panic/fire exit hardware per IBC 1010.1.10, this applies to doors 101, 102and 103. Provide cutsheets on the hardware and show this on your elevations and schedule. 47.5 NEW FIXED GLAZING FIXED MILLWORK FIXED GLAZING FIXED MILLWORK G ELEVATION Egress doors (doors 101, 102, and 103) are required to have a smooth surface on the bottom 10" of the push side per ANSI 404.2.9, provide cutsheets on all swinging egress doors that shows compliance with this requirement. 57.5 47.5 OM 202 - ELEVATION 2 SCALE 1/2" = 1'-0" COAT ROOM 202 - ELEVATION Please verify that thecoat room will be for employee use rather than patrons. Ifpatrons are hanging up their own coats then an additional rackat a max height of 48" must be provided for accessibility.8'-9 1/2"8'-3"PAINTEDMILLWORK OPEN AIRCORRIDOR 3 SCALE 1/2" = 1'-0" DINING ROOM - EXISTING FOR HPC REFERENCE This is not an existing elevation, you are showing the proposedslider door. Please re-title the elevation to accurately depict what you are showing. X7.5 This detail and page are not included in this set. Provide them or remove the reference. cutsheet has been provided and doors revised in drawings to show compliance the 10" is dimensioned on the elevations see revised elevations and plans. Coat room has been eliminated. Elevation tags and labels have been updated on furniture plans and elevation sheets Tags have been revised and coordinated Subject: PlanCheck Page Label: 8.3 1/2" INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf Provide a side view elevation for the accessible portion of the bar demonstrating the required knee and toe clearance. The accessible portion of the bar will need to be at least 60" long to accommodate the one required space plus a companion. Revise and dimension the length of the accessible bar top on all applicable floor plans and elevations. Subject: PlanCheck Page Label: 8.5 1/2" INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf TP dispenser is required to be a minimum of 18" above the floor and the outer end must be within 42" of the back wall (see ANSI fig. 604.7), please revise for both restrooms. Subject: PlanCheck Page Label: 8.5 1/2" INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf Please dimension the size of the knee and toe clearance you've drawn for both restrooms to show compliance with ANSI 306. Subject: PlanCheck Page Label: 8.5 1/2" INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf Bottom edge of the mirror can only be a maximum of 40" above the floor (ANSI 603.3), please revise for both restrooms. Subject: PlanCheck Page Label: 8.5 1/2" INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf Operable part of the toilet must be on the side facing the open restroom, show this to demonstrate compliance for both restrooms. 2'-10"4'-2" E 1/2" = 1'-0" R 202 ELEVATION Provide a side view elevation for the accessible portion of the bar demonstrating the required knee and toe clearance. The accessible portion of the bar will need to be at least 60" long to accommodate the one required space plus a companion. Revise and dimension the length of the accessible bar top on all applicable floor plans and elevations.1'-3"2'-4 7/8"TP HOLDERMOUNTING 1 MEN'S RESTROOM SCALE 1/2" = 1'-0"1 TP dispenser is required to be a minimum of 18" above the floor and the outer end must be within 42" of the back wall (see ANSI fig. 604.7), please revise for both restrooms.5'-7"2'-3 1/2"6 1/2"1'-10"3'-4 7/8"7'-4"PAPERTOWE +TRAS ANSI CLEARANCE 1 SCALE 1/2" = 1'-0"1 S MEN'S RESTROOM M Please dimension the size of the knee and toe clearance you've drawn for both restrooms to show compliance with ANSI 306. 2'-11 3/4" 11 3/4"2'-0"1'-6"6" 7'-1 3/4" STAINLESS STEELGRAB BARSINSTALLED PER2003 ANSI A117.1 3" MEDIUM CHER WOOD FRAME MIRROR BATH 6 -LIGHTBRONZE, 7'-0" AFF LAMINATE VANITYAND BACKSPLASHWITH SOLID COLORCORE Bottom edge of the mirror can only be a maximum of 40" above the floor (ANSI 603.3), please revise for both restrooms.3'-0"1'-6WALLCOVERING 1 SCALE 1/2" = 1'-0"1MEN'S RESTROOM Operable part of the toilet must be on the side facing the open restroom, show this to demonstrate compliance for both restrooms. Bar location changed and section through ANSI bartop provided Exist. TP holder shown with compliant dimensions Knee and toe clearance dimensioned revised operable handle shown Subject: PlanCheck Page Label: 8.5 1/2" INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf Please dimension the height of the paper towel dispenser at the point where the towels are dispensed. Maximum height is 48", please revise for both restrooms. Subject: PlanCheck Page Label: 8.5 1/2" INTERIOR ELEVATIONS Author: justinh File Name: Permit Set.pdf The horizontal side bar is required to extend out 54" minimum from the back wall (see ANSI fig. 604.5.1), please revise for both restrooms. Subject: PlanCheck Page Label: 8.6 HPC ELEVATION STUDY Author: justinh File Name: Permit Set.pdf This does not match the slider door you show on sheet 10.1, there is an additional slider section, the overall length does not match, and you are not showing the swinging man door. Please revise. Subject: PlanCheck Page Label: 10.1 DOOR & WINDOW SCHEDULES Author: justinh File Name: Permit Set.pdf Provide cutsheets on all new proposed fenestration showing compliant U values per IECC C402.4. Subject: PlanCheck Page Label: 10.1 DOOR & WINDOW SCHEDULES Author: justinh File Name: Permit Set.pdf The swinging man door potion of the slider door system is required to have a compliant 10" smooth surface at the bottom of the door and panic hardware just like all other required egress doors. Provide cutsheets demonstrating compliance.5'-7"6'-8"2'-3 1/2"6 1/2"4 7/8"1'-10"3'-4 7/8"7'-1 3/4"7'-4"5'-8 1/4" 3'-5"4 3/4"3'-4"5"WALLCOVERING PAPERTOWEL+TRASH 4" BASE PAINTED TOMATCH DINING ROOM,TYP. DOOR TOHALLWAY WALLCOVERING 3" MEDIUM CHERRYWOOD FRAME ANSI CLEARANCE 1 SCALE 1/2" = 1'-0"1 SCALE 1/2" = 1'-0" MEN'S RESTROOM MEN'S RESTROOMPlease dimension the height of the paper towel dispenser at the point where the towelsare dispensed. Maximum height is 48", please revise for both restrooms.7'-4"2'-10" 3'-6"6" 5'-8 1/4" STAINLES GRAB BAR INSTALLED 2003 ANSI MEN'S 205 UH-1 The horizontal side bar is required to extend out 54" minimum from the back wall (see ANSI fig. 604.5.1), please revise for both restrooms. EXIST. STOREFRONTWINDOW/DOOR SYSTEM NEW FIXED WINDOW EXIST. AWNING TOREMAIN LINE OF EXIST. ROOF TOREMAIN EDGE OF BUILDING EX NEW BRICK TO MATCHEXIST.NEW SINGLE TRACKSLIDING WINDOW/DOORSYSTEM DINING203 MECHANICAL CHASE EXISTING STOREFRONTWINDOWS TO REMAIN PATIO206 BEYOND MECHANICAL CHASE 1 SCALE 1/2" = 1'-0"DINING ROOM - EXTERIOR ELEVATION (EXIST.) 1 SCALE 1/2" = 1'-0"DINING ROOM - EXTERIOR ELEVATION (NEW)This does not matchthe slider door youshow on sheet 10.1,there is an additionalslider section, theoverall length does notmatch, and you arenot showing theswinging man door. Please revise.1 1/2"1 1/2" 5'-0" 7'-0"1 1/2"1 1/2"5'-0"3'-6"1 1/2"1 1/2"3'-6" 2 1/2" 2 1/2"1 1/2"1 1/2"24'-4 1/2" WINDOW 'B'3/4" = 1'-0"WINDOW 'A'3/4" = 1'-0" WIDTH HEIGHT 101FIXED 3'-6"5'-0"7'-0"WOOD A 17.5 0.29 102FIXED 3'-6"5'-0"7'-0"WOOD A 17.5 0.29 103FIXED 3'-6"5'-0"7'-0"WOOD A 17.5 0.29 104FIXED 3'-6"5'-0"7'-0"WOOD A 17.5 0.29105FIXED7'-0"5'-0"7'-0"WOOD B 35 0.29106FIXED7'-0"5'-0"7'-0"WOOD B 35 0.29107FIXED7'-0"5'-0"7'-0"WOOD B 35 0.29 WINDOW SCHEDULE ID AREASIZE COMMENTSSTYLEU-VALUEHEAD HEIGHT TYPEFRAME MATERIAL WIDTH HEIGHT 101FIXED 4'-0"7'-0"7'-0"WOOD A 17.5 0.29 Emergency Egress hardware req. 102FIXED 4'-0"7'-0"7'-0"WOOD A 17.5 0.29 Emergency Egress hardware req. 103FIXED 24'-4 1/2"5'-0"7'-0"WOOD A 17.5 0.29 Single Track Slider System w/ man door DOOR SCHEDULE ID AREASIZE COMMENTSSTYLEU-VALUEHEAD HEIGHT TYPEFRAME MATERIAL Provide cutsheets onall new proposedfenestration showingcompliant U valuesper IECC C402.4.5 PROJECT No:DRAWN BY: DRAWING COPYRIGHT 2018 A CORPS LLC. ALL R DOOR & W SCHEDULE 10 IFFR PERMIT PERMIT SET 24'-4 1/2" 0 1'2'3' The swinging man door potionof the slider door system isrequired to have a compliant 10" smooth surface at thebottom of the door and panichardware just like all other required egress doors. Provide cutsheetsdemonstrating compliance. Dimensions provided. Revised revised and coordinated nana door correspondence provided 10" compliant smooth surface and note regarding panic hardware exception provided I do not see where this was provided, please clarify or submit documentation of nana wall U values. We want to avoid a situation where an wall system that does not meet IECC requirements is installed and the issue is not caught until inspection. Subject: PlanCheck Page Label: 10.1 DOOR & WINDOW SCHEDULES Author: justinh File Name: Permit Set.pdf This door does not match any door shown on your schedule or applicable elevations. Please revise. Subject: PlanCheck Page Label: 10.1 DOOR & WINDOW SCHEDULES Author: justinh File Name: Permit Set.pdf Door type B is not referenced on your schedule, please revise your schedule for consistency.1 1/2"1 1/2"7'-0"3'-6" 2 1/2"2 1/2"1 1/2"1 1/2"7'-0"WINDOW 'B' 3/4" = 1'-0" WINDOW 'A' 3/4" = 1'-0" DOOR 'A' 3/4" = 1'-0" DOOR 'B' 3/4" = 1'-0" SCALE: 3/4" = 1'-0"1 DOOR AND WINDOW ELEVATIONS This door does not match any door shown on your schedule or applicable elevations. Please revise.7'-0"DOOR 'B' 3/4" = 1'-0"VATIONS Door type B is not referenced on your schedule, please revise your schedule for consistency. door dimensioned coordinated notes and dimensions and tags coordinated