The URL can be used to link to this page

Home My WebLink AboutFile Documents.602 E Cooper Ave.0006.2018 (23).ACBK 1 HealthSafe Inspections Inc 390 Apple Drive Basalt CO 81621 970-920-2100 Jim Baker CDPHE Asbestos Building Inspector, Asbestos Air Monitoring Specialist (AMS) & Project Designer Certification #13437 CDPHE Lead-Based Paint Inspector & Lead Hazard Assessor Certification #23607 ASBESTOS REPORT DATE 10/30/2017 CLIENT The Burrell Group c/o Jim Iglehart Construction Company 617 W Main St Aspen CO 81611 PROJECT PROPERTY ADDRESS 602 East Cooper Avenue, Suite #202, Aspen, Colorado 81611 COLORADO & FEDERAL ASBESTOS REGULATIONS SUMMARY Regulation No. 8 Part B – Asbestos of the Colorado Department of Public Health and Environment (CDPHE), Air Quality Control Commission requires a State-certified Asbestos Building Inspector to inspect and collect bulk samples of all suspect asbestos containing materials (ACM) or suspect asbestos containing building materials (ACBM) prior to their disturbance, removal or demolition and disposal. The suspect materials shall be analyzed by a NVLAP accredited laboratory by polarized light microscopy (PLM) using EPA 600 analytical method. A material which is estimated to contain more than 1% asbestos is classified as ACM/ACBM and regulated by the State and Federal governments. Any friable (able to crush or reduce to powder by finger pressure) asbestos 01/18/2018 2 with trace amounts of asbestos fibers or less than 1% must be point-counted using EPA 400 analytical method to prove that it is indeed less than 1%; if not, it must be classified as ACM/ACBM and shall be treated as a State and Federal regulated material. Any friable asbestos containing material (greater than 1% asbestos concentration) or ACM/ACBM that could be rendered friable during its removal or demolition and disposal shall require an asbestos abatement by a certified asbestos abatement contractor to remove and dispose of the material(s). A Colorado State (CDPHE) issued asbestos abatement permit is required for the following trigger levels of ACM/ACBM: 1. Residential buildings of four or fewer units--if more than 32 square feet of any surface coverage (e.g., gypsum wallboard or drywall and associated applied surfacing materials/textures, acoustic sprays, joint compounds, plaster, etc.), 50 feet of asbestos covered or asbestos insulated pipe or any material which would fill a 55-gallon drum is going to be disturbed, removed or disposed of, an asbestos abatement permit is required. 2. Residential complexes with more than four residential units, public access areas to a residential building, commercial and retail buildings, public and civic buildings, industrial buildings--if more than 160 square feet of surfacing materials, 260 linear feet or more than 35 cubic feet (NESHAP) or 55-gallon drum (CDPHE) of suspect ACM/ACBM is going to be disturbed, removed or disposed of, an asbestos abatement permit is required under NESHAP and by the CDPHE. See note below on OSHA. The regulations require an absolute minimum of 3 samples (EPA suggests 9) per homogenous suspect surfacing and TSI materials and an absolute minimum of 1 sample of homogenous miscellaneous materials or any number of “samples sufficient to determine whether a material is ACM” (Reg8.IV.D.3). More samples are required based on surface area or volume. These are minimums; the asbestos building inspector has the field responsibility to determine homogenous materials and the number of samples to collect per material; more than the minimum number of samples may be necessary at the discretion of the inspector. An assessment of friability and functional space conditions of the materials are also the inspector’s field responsibilities. OSHA compliance is required for all employers and employees no matter the quantity of asbestos present with strict regulations regarding 10 sf or more of TSI or friable surfacing materials, and therefore it does not matter what the quantity or State trigger levels are: all suspect ACM/ACBM shall be inspected and tested for asbestos prior to their disturbance, removal and disposal for worker protection and safety. See EPA 40 CFR 763.121 Worker Protection Rule, OSHA 29 CFR 1910.134 Respirator Protection Standard, OSHA 29 CFR 1910.1001 General Industry Standard and OSHA 29 CFR 1926.1101 Construction Standard regulations when dealing with asbestos hazards. Note: County or City regulations may be more stringent. 01/18/2018 3 CLIENT BACKGROUND Jim Iglehart Construction Company hired HealthSafe Inspections, Inc. (hereinafter, HealthSafe) on behalf of his client, The Burrell Group, to perform an asbestos building inspection, bulk sampling and report for changing/removing walls and ceiling in the commercial suite. An inspection and bulk sampling of suspect materials was specific for the removal and changing of interior walls and the removal and disposal of the ceiling tiles—if the final plans call for it. VISUAL INSPECTION & LABORATORY FINDINGS An inspection was conducted by Jim Baker of HealthSafe on Wednesday, October 25, 2017 with Jim Iglehart present during the initial survey. Suspect ACM/ACBM (drywall materials and drop-ceiling tiles only) were identified and sampled. Those materials are the following: 1. Gypsum wallboard/drywall, a homogeneous taped and joint compounded drywall system (classified as a miscellaneous material as a complete integral system) [samples 1-2: 202-ST-W-J-1,2]; these composite layered taped and joint compounded drywall materials are on perimeter and interior walls of the commercial suite in every room with a skip-trowel surfacing material/texture. The estimated surface area is more than 160 sf, but less than 1,000 sf, requiring a minimum of at least two composite core samples of all drywall layers (“…number of samples sufficient to determine” …if asbestos is present or not). The PLM analytical estimated results: NONE DETECTED. 2. Skip-Trowel applied surfacing material/texture, a homogeneous material on the gypsum wallboard/drywall walls, requiring at least three samples with an estimated impact surface area of more than 160 sf, but less than 1,000 sf [samples 3-5: 202-ST-W-T-1,2,3]. The PLM analytical estimated results: NONE DETECTED. 3. A flat, non-textured ceiling tile, a homogeneous miscellaneous material requiring at least one sample [sample 6: 202-C-T1L-FCT, sic., 202-C-TIL-FLT]. The PLM analytical estimated results: NONE DETECTED. 4. A textured ceiling tile, a homogeneous miscellaneous material requiring at least one sample [sample 7: 202-C-T1L-TVT, sic., 202-C-TIL-TXT]. The PLM analytical estimated results: NONE DETECTED. There were no other additional suspect asbestos building materials to sample which were slated to be disturbed, removed or disposed of during the demolition of certain interior walls and ceiling tiles. A total of 7 suspect homogeneous ACM/ACBM bulk samples were collected and 7 samples were analyzed. The bulk samples were analyzed by PLM by a NVLAP accredited laboratory in accordance with Colorado State Regulation 8 for the presence of asbestos mineral fibers. There is NO asbestos in all 7 samples analyzed. See supporting Hayes Microbial Consulting, Inc. data report #17032729. 01/18/2018 4 HEALTHSAFE CONCLUSIONS There is NO asbestos in any of the suspect building materials slated to be impacted by the interior wall changes. NO asbestos abatement will be required. All building materials needing to be removed or disturbed can be dealt with without the concerns for asbestos fibers. All drywall and ceiling tile waste and debris can be disposed of in any landfill which accepts normal, non-hazardous building waste. Sincerely Submitted, Jim Baker 01/18/2018 HMC #17032729 contact@hayesmicrobial.com http://hayesmicrobial.com/ Analysis Report prepared for HealthSafe Inspections 390 Apple Drive Basalt, CO. 81621 Phone: 970-920-2100 Job Name: The Burrell Group 602 E. Cooper Ave., Unit 202 Aspen, CO 81611 Date Sampled: 10-25-2017 Date Analyzed: 10-30-2017 Report Date: 10-30-2017 EPA Laboratory ID# VA01419 NVLAP Lab Code: 500096-0 Asbestos License: 300435 License: #PH-0198 Page 1 of 4 01/18/2018 HMC #17032729 HealthSafe Inspections 390 Apple Drive Basalt, CO 81621 October 30, 2017 Client Job Number: Client Job Name:The Burrell Group 602 E. Cooper Ave., Unit 202 Aspen, CO 81611 Dear HealthSafe Inspections, We would like to thank you for trusting Hayes Microbial for your analytical needs. On October 26, 2017 we received 7 samples by FedEx for the job referenced above. 7 samples were received in good condition. The results in this analysis pertain only to this job, collected on the stated date and should not be used in the interpretation of any other job. This report may not be duplicated, except in full, without the written consent of Hayes Microbial Consulting, LLC. This laboratory bears no responsibility for sample collection activities, analytical method limitations, or your use of the test results. Interpretation and use of test results are your responsibility. Any reference to health effects or interpretation of mold levels is strictly the opinion of Hayes Microbial Consulting. In no event, shall Hayes Microbial Consulting or any of its employees be liable for lost profits or any special, incidental or consequential damages arising out of your use of the test results. Steve Hayes, BSMT(ASCP) Laboratory Director Hayes Microbial Consulting, LLC Page 2 of 4 01/18/2018 HMC #17032729 EPA 600/R-93, M-4/82-020 (PLM)HealthSafe Inspections 390 Apple Drive Basalt, CO 81621 Phone: 970-920-2100 Job Number: Collected by: Email: Jim Baker healthsafeinspections@gmail.com Job Name:The Burrell Group 602 E. Cooper Ave., Unit 202 Aspen, CO 81611 Date Collected: Date Received: Date Reported: 10/25/2017 10/26/2017 10/30/2017 #Sample Name Description Asbestos Fibers Other Fibers Non- Fibers 1 1 202-ST-W-J-1 Drywall / White (None Detected) 10 % Cellulose fibers 90 % Layer 2 202-ST-W-J-1 Joint Compound / White (None Detected) (None Detected) 100 % 2 2 202-ST-W-J-2 Drywall / White (None Detected) 10 % Cellulose fibers 90 % Layer 2 202-ST-W-J-2 Joint Compound / White (None Detected) (None Detected) 100 % 3 3 202-ST-W-T-1 Texture / White (None Detected) 3 % Cellulose fibers 97 % 4 4 202-ST-W-T-2 Texture / White (None Detected) 2 % Cellulose fibers 98 % 5 5 202-ST-W-T-3 Texture / White (None Detected) <1 % Cellulose fibers 100 % 6 6 202-C-T1L-FCT Ceiling Tile / White (None Detected) 65 % Cellulose fibers 5 % Fiberglass 30 % 7 7 202-C-T1L-TVT Ceiling Tile / Brown (None Detected) 65 % Cellulose fibers 35 % Signature: Date:10/30/2017 Reviewed by: Date:10/30/2017 Page 3 of 4 01/18/2018 HMC #17032729 Asbestos - Additional InformationHealthSafe Inspections 390 Apple Drive Basalt, CO 81621 Phone: 970-920-2100 All samples were received in acceptable condition unless otherwise noted on the report. The Report must not be used by the client to claim product certification, approval, or endorsement by: AIHA, NIST, NVLAP NY ELAP, or any agency. The results relate only to the items tested. The results include an inherent uncertainty of measurement associated with estimating percentages by polarized light microscopy. Measurement uncertainty data can be provided when requested. None detected: Below the detected reporting limit of 1% unless point counting is performed, then the detected, reporting limit is .25%. Per NY ELAP198.6 (NOB) TEM is the only reliable method to declare an NOB material as Non-Asbestos Containing. Hayes Microbial Consulting reserves the right to dispose of all samples after a period of 60 days in compliance with state and federal guidelines. Signature: Date:10/30/2017 Reviewed by: Date:10/30/2017 Page 4 of 4 01/18/2018 01/18/2018 01/18/2018