The URL can be used to link to this page

Home My WebLink AboutFile Documents.800 S Mill St.0105.2018.ARBK0105-2018-ARBK_BuildingComments_1 Page: - 1 HOUR RATED FLOOR ASSEMB 2 File Name: 3 Fifth Ave Drawings.pdf Subject: PlanCheck Author: nickt Color: Provide a cut sheet on the whisper mat demonstrating an IIC rating of 50 or greater at this floor configuration. 3 Fifth Ave Drawings.pdf (7) Page: - 1 HOUR RATED FLOOR ASSEMB 2 File Name: 3 Fifth Ave Drawings.pdf Subject: PlanCheck Author: nickt Color: Provide the original installation instructions for a listed 1 hour fire, STC 50 rated wall assembly. Page: 1 - EXISTING FLOOR PLAN File Name: 3 Fifth Ave Drawings.pdf Subject: asbestos Author: nickt Color: Provide an asbestos abatement clearance report. Page: 2 - DEMOLITION FLOOR PLAN File Name: 3 Fifth Ave Drawings.pdf Subject: PlanCheck Author: nickt Color: Mantle, surround, and hearth extension must comply with the installation instructions of the factory built firebox. Demonstrate compliance. If no manufacturer instructions can be found, demonstrate compliance with the requirements of 2015 IBC chapter 21. 1 HOUR RATED FLOOR ASSEMBLY55 STC 1 HOUR RATED WALL ASSEMBLY55 STC Sketch "NOT FOR CONSTRUCTION" without ASI no. DETAILSketch Name:1 HOUR RATED ASSEMBLIES Project Name:Project Number:800 S. MILL STREET, UNIT 10-BN/A Sketch No. - Item No.: ASI Reference: 04/11/2018 A-1N/A Date: Scale:1" = 1'-0"A-1Drawing Sheet / SpecSection:300 S. SPRING ST. SUITE 201ASPEN, CO 81611(970) 710-2938 THUNDERBOWL ARCHITECTS EXISTING GYP. WALL BOARD IN ADJACENT UNIT. NOT TO BE DISTURBED. EXISTING(ADJACENT UNIT)PROPOSED EXISTINGEXISTING(ADJACENT UNIT) EXISTING STAGGERED STUDS. NOT TO BE DISTURBED. EXISTING GYP. WALL BOARD TO BE REMOVED (THIS UNIT ONLY) EXISTING INSULATION TO REMAIN. REPLACE AS NECESSARY ALL EXISTING PLYWOOD NOT TO BE DISTURBED. REPLACE ALL EXISTING GYP. WALL BOARD W/58" TYPE "X" GYP. WALL BOARD TO MEET 55 STC RATING WOOD FLOORTILE FLOOR EXISTING(ADJACENT UNIT BELOW) EXISTING GYP. WALL BOARD IN ADJACENT UNIT. NOT TO BE DISTURBED. NEW WOOD FLOOR ASSEMBLY NEW 12" WHISPER MAT, ASTM E90 EXISTING INSULATION TO REMAIN. ALL EXISTING PLYWOOD SUB-FLOOR NOT TO BE DISTURBED. EXISTING FLOOR STRUCTURE TO REMAIN. NEW TILE FLOOR ASSEMBLY 1A-1 2A-1 1" = 1'-0" 1" = 1'-0"Provide a cut sheet onthe whisper matdemonstrating an IICrating of 50 or greaterat this floorconfiguration. 1 HOUR RATED FLOOR ASSEMBLY55 STC 1 HOUR RATED WALL ASSEMBLY55 STC Sketch "NOT FOR CONSTRUCTION" without ASI no. DETAILSketch Name:1 HOUR RATED ASSEMBLIESProject Name:Project Number:800 S. MILL STREET, UNIT 10-BN/A Sketch No. - Item No.:ASI Reference: 04/11/2018 A-1N/A Date: Scale:1" = 1'-0"A-1Drawing Sheet / SpecSection:300 S. SPRING ST. SUITE 201ASPEN, CO 81611(970) 710-2938 THUNDERBOWLARCHITECTS EXISTING GYP. WALL BOARD IN ADJACENT UNIT. NOT TO BE DISTURBED. EXISTING(ADJACENT UNIT)PROPOSED EXISTINGEXISTING(ADJACENT UNIT) EXISTING STAGGERED STUDS. NOT TO BE DISTURBED. EXISTING GYP. WALL BOARD TO BE REMOVED (THIS UNIT ONLY) EXISTING INSULATION TO REMAIN. REPLACE AS NECESSARYALL EXISTING PLYWOOD NOT TO BE DISTURBED. REPLACE ALL EXISTING GYP. WALL BOARD W/58" TYPE "X" GYP. WALL BOARD TO MEET 55 STC RATING WOOD FLOORTILE FLOOR EXISTING(ADJACENT UNIT BELOW) EXISTING GYP. WALL BOARD IN ADJACENT UNIT. NOT TO BE DISTURBED. NEW WOOD FLOOR ASSEMBLY NEW 12" WHISPER MAT, ASTM E90 EXISTING INSULATION TO REMAIN. ALL EXISTING PLYWOOD SUB-FLOOR NOT TO BE DISTURBED. EXISTING FLOOR STRUCTURE TO REMAIN. NEW TILE FLOOR ASSEMBLY 1A-1 2A-1 1" = 1'-0" 1" = 1'-0" Provide the originalinstallation instructionsfor a listed 1 hour fire,STC 50 rated wallassembly. PROJECT:VOGEL RESIDENCE by the users (contractors, millwork manufacturers, etc.) to ensure the design is adequate for the intended use. These drawings will be revised periodically and it shall be the re-sponsibility of the receiver of these drawings to keep them current with any updates. 2. Cabinetry Notes: Millwork manufacturer to field verify all dimensions prior to building cabinetry. EXISTING FLOOR PLAN Scale: 1/4” = 1’-0” Provide an asbestos abatement clearance report. 02/12/18 12/20/1701/12/1801/16/18 DRW NO:DATE:DRAWING TITLE:PROJECT:VOGEL RESIDENCE ng Notes: nished for ensions c. All d or cal-d. Use of g design e checked s, millwork ensure the he intended evised be the re-er of these current with o field verify uilding 2DEMOLITION FLOOR PLAN ON FLOOR PLAN g A-1 Rating sembly. all and s.4/16/2018 06/08/2018 Mantle, surround, and hearth extensionmust comply with the installationinstructions of the factory built firebox.Demonstrate compliance. If nomanufacturer instructions can be found,demonstrate compliance with therequirements of 2015 IBC chapter 21. EXISTING WOOD FIREPLACE TO REMAIN NOTED ON DRAWINGS 3 and 14 SEE ATTACHED CLEARANCE LETTER SEE DETAIL 3/SK-01 INCLUDED IN DRAWING PACKAGE 8.21.2018 SEE ATTACHED Proflex 90 spec Page: 2 - DEMOLITION FLOOR PLAN File Name: 3 Fifth Ave Drawings.pdf Subject: PlanCheck Author: nickt Color: Provide more information on the attic and the proposed water heater relocation. This building is Type VA construction and is multifamily. To locate mechanical equipment in the attic, the attic above the unit must be separated from adjacent units and from adjacent attics serving other units by 1 hour fire resistant construction (2015 IBC 420). Additionally, the roof structure must have a 1 hour fire rating (2015 IBC 711.2.6). Provide access and service space in accordance with 2015 IMC 306; demonstrate combustion air needs are met per 2015 IFGC 304; and demonstrate exhaust termination is located in accordance with 2015 IMC 501.3.1. Detail whether this is to be a new water heater or reuse the old one. Provide a drain pan per 2015 IPC 504.7. Page: 2 - DEMOLITION FLOOR PLAN File Name: 3 Fifth Ave Drawings.pdf Subject: PlanCheck Author: nickt Color: This is a Type VA building, requiring the floor/ceiling assembly to be 1 hour fire rated (2015 IBC 601). Provide a listed 1 hour fire rated ceiling assembly. Page: 3 - FLOOR PLAN File Name: 3 Fifth Ave Drawings.pdf Subject: PlanCheck Author: nickt Color: It appears that you are replacing the exterior doors. Note that they must have a U factor of 0.28 or less on the plans. (Ordinance 40, 2016) 02/12/18 12/20/1701/12/1801/16/18 DRW NO:DATE:DRAWING TITLE:PROJECT:VOGEL RESIDENCE General Notes1. Construction Drawing Notes: These drawings are furnished for information only. All dimensions shown are sheet specific. All dimensions shall be read or cal-culated and never scaled. Use of these drawings (including design and dimensions) must be checked by the users (contractors, millwork manufacturers, etc.) to ensure the design is adequate for the intended use. These drawings will be revised periodically and it shall be the re-sponsibility of the receiver of these drawings to keep them current with any updates. 2. Cabinetry Notes:Millwork manufacturer to field verify all dimensions prior to building cabinetry. 2DEMOLITION FLOOR PLAN DEMOLITION FLOOR PLANScale: 1/4” = 1’-0” See Drawing A-1 For 1 Hour Rating & Sound Assembly. Demising Wall and Floor Details.4/16/2018 06/08/2018 Provide more information on the attic and the proposed water heater relocation. This building isType VA construction and is multifamily. To locate mechanical equipment in the attic, the atticabove the unit must be separated from adjacent units and from adjacent attics serving other unitsby 1 hour fire resistant construction (2015 IBC 420). Additionally, the roof structure must have a1 hour fire rating (2015 IBC 711.2.6). Provide access and service space in accordance with 2015IMC 306; demonstrate combustion air needs are met per 2015 IFGC 304; and demonstrateexhaust termination is located in accordance with 2015 IMC 501.3.1. Detail whether this is to bea new water heater or reuse the old one. Provide a drain pan per 2015 IPC 504.7. 02/12/18 12/20/1701/12/1801/16/18 DRW NO:DATE:DRAWING TITLE:PROJECT:VOGEL RESIDENCE ing Notes: rnished for mensions fic. All ad or cal-ed. Use of ing design be checked ors, millwork ensure the the intended revised be the re-ver of these current with to field verify building 2DEMOLITION FLOOR PLAN ON FLOOR PLAN” g A-1 Rating ssembly. Wall and s.4/16/2018 06/08/2018 This is a Type VAbuilding, requiring thefloor/ceiling assemblyto be 1 hour fire rated(2015 IBC 601).Provide a listed 1 hourfire rated ceilingassembly. 02/12/18 12/20/1701/12/1801/16/18 DRW NO:DATE:DRAWING TITLE:PROJECT:VOGEL RESIDENCE General Notes1. Construction Drawing Notes: These drawings are furnished for information only. All dimensions shown are sheet specific. All dimensions shall be read or cal-culated and never scaled. Use of these drawings (including design and dimensions) must be checked by the users (contractors, millwork manufacturers, etc.) to ensure the design is adequate for the intended use.These drawings will be revised periodically and it shall be the re-sponsibility of the receiver of these drawings to keep them current with any updates. 2. Cabinetry Notes: Millwork manufacturer to field verify all dimensions prior to building cabinetry. 3FLOOR PLAN FLOOR PLANScale: 1/4” = 1’-0” It appears that you arereplacing the exteriordoors. Note that theymust have a U factorof 0.28 or less on theplans. (Ordinance 40,2016) EXISTING EXTERIOR DOORS TO REMAIN NOTED ON DRAWING 2 SEE DETAIL 3/SK-01 SEE DETAIL 1/SK-01 AS NOTED ON DRAWING 3a 399 CFM RANGE HOOD NOTED ON DRAWING 3 NEW WATER HEATER w/DRAIN PAN NOTED ON DRAWING 3a 5/8 DRYWALL ALL WALLS, TYP. UNLESS NOTED NOTED ON DRAWINGS 3 STRUCTURAL FRAMING SEE DRAWINGS S1,S2,and S3 MECH ACCESS NOTED ON DRAWING 3a