Loading...
HomeMy WebLinkAboutFile Documents.353 Pfister Dr.0057-2022-BROF (7) ESR-2154 ES REPORT"' Issued January 1, 2007 This report is subject to re-examination in one year. ICC Evaluation Service, Inc. Business/Regional Office•5360 Workman Mill Road,Whither,Calrfornia 90601 •(562)699-0543 Regional Office•900 Montclair Road,Suite A,Birmingham,Alabama 35213 •(205)599-9800 www.ICC-es.org Regional Office•4051 West Flossmoor Road,Country Club Hills,Illinois 60478•(708)799-2305 DIVISION: 07—THERMAL AND MOISTURE PROTECTION on both sides with a polymer coating. The underlayment is Section: 07305—Roofing Felt and Underlayment produced in white, black and grey colors. The underlayment has a nominal weight of 4 pounds per 100 square feet(191 REPORT HOLDER: g/m2)and is produced rolls of varying size. 3.2 TITANIUMT"' UDL-50 (MLT Synthetic 50) Roofing INTERWRAP INC. Underlayment: 32923 MISSION WAY MISSION, BRITISH COLUMBIA V2V 6E4 TITANIUMTM UDL-50 (MLT Synthetic 50) roofing CANADA underlayment is a synthetic sheet-type underlayment (604)820-5400 comprised of a woven core coated on both sides with a www.interwrap.com polymer coating. The underlayment is grey in color. The msethinterwrap.com underlayment has a nominal weight of 4.7 pounds per 100 square feet(224 g/m2)and is produced in rolls of varying size. EVALUATION SUBJECT: 4.0 INSTALLATION 4.1 General: TITANIUMT'" UDL-30 AND TITANIUMT"' UDL-50 ROOFING UNDERLAYMENT Installation must comply with the applicable code,this report and the manufacturer's published installation instructions. In ADDITIONAL LISTEE: the event of conflict between the manufacturer's instructions and this report, this report governs. The installation MONIERLIFETILE instructions must be available at the jobsite during 7575 IRVINE CENTER DRIVE installation. SUITE 100 Prior to application of the underlayment, the deck surface IRVINE, CALIFORNIA 92618-2930 must be dry, free of moisture, dust and dirt, loose nails, and other protrusions.Damaged sheathing must be replaced.The MLT SYNTHETIC 50 underlayment is laid horizontally(parallel to the eave)starting at the lowest eave point, printed side up, with 4-inch (102 1.0 EVALUATION SCOPE mm) horizontal (head) laps and 6-inch (152 mm) vertical (end)laps. Overlaps run with the flow of water in a shingling Compliance with the following codes: manner. The TITANIUMTM UDL-30 underlayment must be • 2006 International Building Code°(IBC) attached to the roof deck using ring shank roofing nails having 1-inch-diameter (25.4 mm) plastic caps. The • 2006 International Residential Code®(IRC) TITANIUMTM UDL-50(MLT Synthetic 50)must be attached to Properties evaluated: the structural roof deck material using 3/8-inch-diameter head corrosion-resistant roofing nails, tin tag caps and nails; • Physical properties screws with washers; plastic cap staples and plastic cup • Water resistance nails. The fasteners are spaced 12 inches (305 mm) on center vertically and 24 inches (610 mm) on center 2.0 USES horizontally in accordance with the surface markings on the TITANIUMTM UDL-30 and TITANIUMTM UDL-50 (MLT exposed face of the underlayment. When battens or Synthetic 50) roofing underlayments are synthetic roofing counterbattens are installed over the underlayment, the underlayments intended for use as alternatives to ASTM D underlayment need only be preliminarily attached pending 226, Type I and Type II, roofing underlayment specified in attachment of the battens or counterbattens. Chapter 15 of the IBC and Chapter 9 of the IRC.Additionally, In areas of the roof required to have an ice barrier under the TITANIUMTM UDL-30 and TITANIUMTM UDL-50 (MLT Chapter 15 of the IBC or Chapter 9 of the IRC, two layers of Synthetic 50)roofing underlayment is intended for use as an the TITANIUMTM UDL-30 or TITANIUMTM UDL-50 (MLT alternative to the ice barrier specified in Chapter 15 of the IBC Synthetic 50) underlayment are cemented together with a and Chapter 9 of the IRC. These products were recognized roofing cement complying with ASTM D 4586(asbestos free), under ICC-ES ER-6043. extending for a minimum distance of 24 inches (610 mm) 3.0 DESCRIPTION inside the exterior wall line of the building.As an alternative, a self-adhering polymer modified bitumen sheet complying 3.1 TITANIUMTM UDL-30 Roofing Underlayment: with ASTM D 1970 or recognized in an ICC-ES evaluation TITANIUMTM UDL-30 roofing underlayment is a synthetic report as complying with the ICC-ES Acceptance Criteria for sheet-type underlayment comprised of a woven core coated Severe Climate Underlayments (AC48), is permitted to be t ., REPORTS'" are not to be construed as representing aesthetics or any other attributes not specifically addressed,nor are they to be construed as an -rA0r Ii endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service,Inc.,express or implied,as to any ANSI finding or other matter in this report,or as to any product covered by the report. I . : /2 0 2 2 i-...Rea .•- PRODUCT CERTIFICATION Copyright©2007 Pagp\tl N '�l1ILDING DEPARTMENT Page 2 of 2 ESR-2154 applied over the solid substrate in sufficient courses so that 5.4 Installation is limited to roofs with ventilated attic spaces the underlayment extends up the roof a distance equal to the in accordance with the requirements of the applicable distance of 24 inches (610 mm) inside the exterior wall line. code. The TITANIUMTM UDL-30 or TITANIUMTM UDL-50 (MLT Synthetic 50) roofing underlayment, in the field of the roof, 5.5 Installation is limited to roofs where nonclassified roof overlaps the ice barrier protection. coverings are permitted. Installation of an approved roof covering can proceed 5.6 The products are manufactured in Mission, British immediatelyfollowing application of the roofing underlayment. Columibia,Canada,under a quality control program with The underlayment must be covered by the roof covering inspections by Intertek Testing Services NA Inc. (AA- within the time period set forth in the manufacturer's 691). published installation instructions. 6.0 EVIDENCE SUBMITTED 4.2 Reroofing: 6.1 Data in accordance with the ICC-ES Acceptance For reroofing applications, the same procedures set forth in Criteria for Roof Underlayments (AC188), dated Section 4.1 apply after removal of the existing roof covering February 2003(editorially revised January 2005),for the and roofing felts to expose the roof deck. TITANIUMTM UDL-30 underlayment. 5.0 CONDITIONS OF USE 6.2 Data in accordance with the ICC-ES Acceptance Criteria for Roof Underlayment for Use in Severe The TITANIUMTM UDL-30 and TITANIUMTM UDL-50 (MLT Climate Areas (AC48), dated October 2005, for the Synthetic 50) roof underlayments described in this report TITANIUMTMUDL-50(MLT Synthetic 50)underlayment. comply with, or are suitable alternatives to what is specified in, those codes listed in Section 1.0 of this report, subject to 7.0 IDENTIFICATION the following conditions: Each roll of the TITANIUMTM UDL-30 and TITANIUMTM UDL- 5.1 Installation is limited to roofs with a slope of 2:12 50 (MLT Synthetic 50) roofing underlayments described in (16.67%)or greater. this report is to be marked with the manufacturer's name [Interwrap Inc. (MonierLifetile)], name of the product 5.2 Installation is limited to use with roof coverings that do [TITANIUMTM UDL-30orTITANIUMTM UDL-50(MLTSynthetic not involve hot asphalt or coal-tar pitch. 50)], the date code of manufacture, the evaluation report 5.3 Installation is limited to use with approved roof number (ESR-2154 or ER-6043) and the name of the coverings that are mechanically fastened through the inspection agency(Intertek Testing Services NA, Inc.). underlayment to the sheathing or rafters. RECEIVED 07/08/2022 ASPEN BUILDING DEPARTMENT