The URL can be used to link to this page

Home My WebLink AboutFile Documents.533 W Hallam St.0031-2022-BCHO (9)VaproShield LLC | 915 26th Ave. N.W. | Suite C5 | Gig Harbor, WA 98335 | Toll Free 1-866-731-7663 | www.VaproShield.com | 08/09/21 Product Description WrapShield IT Integrated Tape WRB/Air Barrier membrane protects the building envelope by allowing vapor to pass through (breathable) but not air or liquid water mitigating costly moisture damage and saving energy for the life of the building. BASIC USE WrapShield IT Integrated Tape is installed above grade behind rain screen wall cladding assemblies. MATERIALS WrapShield IT Integrated Tape consists of multiple layers of spun- bonded polypropylene fabric with clear integrated horizontal tape and a pre-marked lap template to ensure accurate horizontal seam installation. BENEFITS Superior building envelope protection – high drying capacity (59 perms) allows building materials to dry-out, reducing the risk of damage from moisture infiltration, mold, mildew and rot for the life of the building. Factory installed clear integrated tape – seals horizontal seams ensuring the upper layer shingles over the lower layer creating the 6” shingled effect. Pre-marked shingle template – increases installation accuracy. Air tight barrier – stops air infiltration as per the ASTM 2357 Air Barrier assembly test. Consistent millage thickness – factory made rolled good ensures consistent properties and performance. Fully tested building envelope system – rough opening flashing accessories eliminate the need for untested outside components. Mechanically attaches – to multiple substrates using VaproCaps™. 1 of 4 WrapShield IT ® Integrated Tape a mechanically attached, water resistive vapor permeable air barrier membrane with integrated tape at the horizontal seams: Product No: 16109000 WrapFlashing Product No.: 40105500 / 40108000 PHYSICAL PROPERTIES PROPERTY RESULT Color Orange (top), White (back) Thickness 0.5581 mm (21.97 mil) Membrane Weight 193.7 g/m2 ( 0.635 oz/ft2) Roll Weight 32 lbs (14 kg) Roll Dimensions 59" x 164' (1.5m x 50m) Roll Coverage 807 sq. ft. (75 sq. m.) Skid 25 Rolls VOCs None Ultra Violet Light Exposure 180 days maximum Minimum Application Temperature None Service Temperature minus 40°F (-40°C) - 225°F (107°C) Warranty 20 year material warranty PRODUCT DATA SHEET Simple installation – requires only basic tools, no specialized mobilizations or protection gear are required. Install on dry and/or saturated substrates – eliminates additional water accumulation by locking out liquid water, allowing vapor diffusive drying and helping to “dry-in” the build. Spans substrate joint gaps up to 7/8” (22.2mm), eliminates need for tapes and fillers. Phase construction ready, install in all temperatures sustains up to 180 days UV and climate exposure prior to cladding installation. Emits zero VOCs, no primer required, ensuring crew safety and a healthy building. Technical Data & Environmental Passed and tested to industry standards for Weather Resistive Barriers. WrapShield IT Integrated tape emits zero VOCs, making the membrane safe for work crews and occupants for the life of the building. • OSB • Exterior Gypsum Sheathing • Rigid Insulation • Precast Concrete • Concrete Block • Cast-in-place Concrete • Plywood • Pre-painted Steel • Galvanized Metal • Aluminum (Painted/Mill Finish) • Anodized Aluminum • Vinyl Window and Door Frames • Fiberglass Window and Door Frames Contact VaproShield Technical – if you have additional substrate questions. Compatible Substrates 05/17/2022 VaproShield LLC | 915 26th Ave. N.W. | Suite C5 | Gig Harbor, WA 98335 | Toll Free 1-866-731-7663 | www.VaproShield.com | 08/09/21 2 of 4 PRODUCT DATA SHEET Complete Building Envelope System WRB/AIR BARRIER WrapShield IT Integrated Tape BEST PRACTICE INSTALLATION Secure membrane with stainless steel stapes above integrated tape. Align the bottom of the upper course with the dotted line for proper 6” (15 cm) overlap. Join horizontal seams by peeling back both release films. Tape seals horizontal seams. Upper course is now properly shingled over the lower course, eliminating water concerns at the horizontal joints. Roll the integrated tape seam with floor roller to ensure full contact BEST PRACTICE VERTICAL SEAMS Overlap vertical seams by min. 12”. Apply ¼” (6.4 mm) bead of VaproBond adhesive sealant to ensure water and air barrier seal. Peel back release films to finish hori- zontal seam. For complete installation instructions, visit VaproShield.com. WrapShield IT Product No.: 16109000 / WrapFlashing Product No.: 40105500 / 40108000 Rough Opening Flashing Membranes Product Part No.Roll Sizes WrapFlashing SA Self-Adhered Roll 46105590 46108090 Roll Size: 11 3/4” x 164’ (298mm x 50m) 161 S/F (15 S/M) Roll Size: 19 2/3” x 164’ (500mm x 50m) 269 S/F (25 S/M) WrapFlashing Roll (Mechanically Attached) 40105500 40108000 Roll Size: 11 3/4” x 164’ (298mm x 50m) 161 S/F (15 S/M) Roll Size: 19 2/3” x 164’ (500mm x 50m) (25 S/M) Weight: 9.5lbs (4.3kg) ROUGH OPENING FLASHING OPTIONS The following rough opening flashing components can be used: • VaproLiqui-Flash™ • BlockFlashing™ • VaproBond™ Reference individual data sheets for comprehensive information. In conjunction with: Window and Rough Openings Flashing VaproLiqui-Flash BlockFlashing VaproBond Application Temperature 35°F to 110°F (1.7°C to 43°C) 0°F to 180°F (-18°C to 82°C) 20°F to 120°F (-6.7°C to 49°C) Drying Capacity Breathable Permeability High None Low Application Method Sausage Gun / Putty Knife or Brush Utility Knife / J-Roller Sausage Gun / Putty Knife Visit VaproShield.com to review additional flashing options.05/17/2022 VaproShield LLC | 915 26th Ave. N.W. | Suite C5 | Gig Harbor, WA 98335 | Toll Free 1-866-731-7663 | www.VaproShield.com | 08/09/21 3 of 4 PRODUCT DATA SHEET RELATED LEED CREDITS VaproShield membranes qualify for LEED credits. Visit VaproShield.com for the latest sustainability and LEED information. Installation STORAGE AND HANDLING Store material rolls on end in original packaging. Protect rolls from direct sunlight and inclement weather until ready for use. SAFETY Work crews are safe around VaproShield membranes. WrapShield IT Integrated Tape contains zero VOCs or toxins. PREPARATION All surfaces must be dry, sound, clean, “as new” condition, and free of oil, grease, dirt, excess mortar or other contaminants detrimental to the adhesion of the water resistive air barrier membrane and flashings. Fill voids and gaps in substrate greater than 7/8 inch (22.2 mm) in width to provide an even surface. Strike masonry joints full-flush. BEST PRACTICE INSTALLATION Install WrapShield IT with approved fasteners in a horizontal, shingle fashion. Horizontal overlaps must be 6” (15 cm) to properly seal the integrated tape joint. Vertical overlaps must be minimum 12” (30 cm) and require VaproBond adhesive sealant, to provide an air barrier seal. Vertical overlaps are to be staggered a minimum of 24” (61 cm) and should not occur directly above or below windows or doors. Inside and outside corners can be continuous, or if a vertical joint occurs within 24” horizontally, an overlap of 12” minimum in both directions is required, providing a double layer at the corner.” Visit www.VaproShield.com for complete installation instructions and instructional videos. LIMITATIONS WrapShield IT Integrated Tape should be covered within 180 days of installation. Do not contaminate WrapShield IT Integrated Tape WRB/ Air Barrier with building site chemicals which make it more wettable (e.g., surfactants), This will adversely affect its water resistance and therefore its contribution to the water resistance of the overall wall system. WrapShield IT Integrated Tape WRB/Air Barrier should not be subjected to asphaltic materials, chemicals, surfactants, or cleaning compounds that could affect the water resistance of the membrane surface; if exposed, replace effected membrane. Availability VaproShield products are available throughout North America, Central and South America, and New Zealand. Warranty A 20-year material warranty is available. Commercial Window Rough Opening Flashing System with WrapFlashing SA WrapFlashing SA Self-Adhered properly shingled; applied directly to field membrane + folded 2.75” inside of rough opening VaproLiqui-Flash full coverage inside rough opening + 1” on face Visit VaproShield.com to view full installation sequence Field membrane cut flush with edge of R.O. - Membrane is left unattached until window and head flashing are installed WrapShield IT field membrane installed horizontally 9”11.75” WrapShield IT Product No.: 16109000 / WrapFlashing Product No.: 40105500 / 40108000 05/17/2022 VaproShield LLC | 915 26th Ave. N.W. | Suite C5 | Gig Harbor, WA 98335 | Toll Free 1-866-731-7663 | www.VaproShield.com | 08/09/21 4 of 4 PRODUCT DATA SHEET TESTING DATA PROPERTY STANDARD RESULT Strength Dry Tensile Strength ≥ 20 lbf/in ASTM D828 Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus MD - 171 N (38.6 Ib/in) XMD - 104 N (23.3 Ib/in) Dry Tensile Strength ASTM D882 Standard Test Method for Tensile Properties of Thin Plastic Sheeting Control - 8.89 N/mm (50.8 Ib/in) UV Exposure - 8.16 N/mm (46.6 Ib/in) UV + Heat Exposure - 8.16 N/mm (46.6 Ib/in) Dry Breaking Force (Grab method) MD ≥40 XMD ≥35 ASTM D5034 Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) MD – 445.3 N (100.1 lbf) CD – 383.0 N (86.1 lbf) Cold Mandrel Bend Test AC38 Section 3.3.4 Warp (Machine) Direction - No cracking Filling (Cross) Direction - No cracking Weathering Tests AC38 Section 4.1.2 UV Exposure AC38 Section 4.1.3 Accelerated Aging UV - No visual change UV & Accelerated - visibly lighter, no visible deterioration Water Vapor Transmittance Water Vapor Transmission Desiccant Method, Procedure A, 24.4°C (76.0°F) 50 %RH ASTM E96 Standard Test Methods for Water Vapor Transmission of Materials 21 Perm (grain/h•ft2•inchHg) 1201 ng/Pa•s•m2 Water Vapor Transmission Water Method, Procedure B, 24.4°C (76.0°F) 50 %RH ASTM E96 Standard Test Methods for Water Vapor Transmission of Materials 66.9 Perm (grains/hr•ft2•inchHg) 3828 ng/Pa•s•m2 Water Vapor Transmission Dynamic Relative Humidity Measurement (23°C 50 %RH) ASTM E398 Standard Test Method for Water Vapor Transmission Rate of Sheet Materials Using Dynamic Relative Humidity Measurement 71.91 Perm (grain/h•ft2•inchHg) 4114 ng/Pa•s•m2 Air Resistance Testing Air Permeance ASTM E2178 @75 Pa Standard Test Method for Air Permeance of Building Materials 0.0004 L/s•m2 @ 75 Pa (0.0001 cfm/ft2 @ 1.57 psf) Air Barrier ASTM E2357 Standard Test Method for Determining Air Leakage of Air Barrier Assemblies <0.01 L/s•m2 @ 75 Pa (<0.01 cfm/ft2 @ 1.57 psf) Air Barrier ASTM E283 Standard Test Method for Determining Rate of Air Leakage Through Exterior Win- dows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen <0.01 L/s•m2 @ 75 Pa (<0.01 cfm/ft2 @ 1.57 psf) Water Resistance Testing Nail Sealability ASTM D1970/ section 7.9 Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection Pass - Review Fastener Penetrations Technical Bulletin at VaproShield.com Water Resistance (Boat Test) ASTM D779 Standard Test Method for Water Resistance of Paper, Paperboard, and Other Sheet Materials by the Dry Indicator Method (Withdrawn 2011) Control - No leakage Weathered - No Leakage Water Resistance (Control after Weathering) AATCC 127 Hydrostatic pressure test (550 mm water column for 5 hours), American Association of Textile Chemists and Colorists Control - No leakage Weathered - No Leakage Static Water Penetration Test ASTM E331 Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference" Mockup tested at 15 psf for 15 minutes, No leaks Fire Testing Flame Spread Smoke Developed ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials Flame Spread 0 Smoke Developed 55 NFPA 285 Compliant ASTM E1354 Standard Test Method for Heat and Visible Smoke Release Rates for Materi- als and Products Using an Oxygen Consumption Calorimeter View over 50 compliant assemblies with various manufacturers at VaproShield.com or Contact VaproShield Technical Team, 1-866-731-7663 opt. 5 WrapShield IT Product No.: 16109000 / VaproFlashing Product No.: 40105500 / 40108000 TESTING DATA PROPERTY STANDARD RESULT CANADIAN STANDARDS Air Leakage Rate CAN/CGSB 51.32 Classification A1 - PASS Multiple CAN/ULC-S742-11 – Sheathing Membrane, Breather Type PASS 05/17/2022