Loading...
HomeMy WebLinkAboutFile Documents.200 S Aspen St.0007.2017 (59).ACBK Dear Caet: I appreciate the opportunity to offer this updated proposal for a custom PhantomPark lift for your 200 South Aspen project. This quote reflects the recent revision to the vertical travel and platform size required for this lift as well as an updated drawing. Please read the following specifications to ensure I have quoted your requirements accurately and completely. Please note the proposal does not include freight or installation. I will happy to obtain an estimated freight quote though if it will be some time before the lift is installed the freight quote is subject to change. In regards to installation, I will be happy to refer you to a qualified installer that can provide you with an estimate to install the lift. The lift is designed to allow the driver to stay with the car and remain on the lift while it is in operation. I trust you will find everything as requested. If you have any questions please feel free to contact me. Again, thank you for contacting American Custom Lifts. Caet Fox Forum Phi Architects 715 West Main Suite 204 Aspen, CO 81611 24-Jan-17 Sincerely, Blaine Davies American Custom Lifts 8880 Rio San Diego Drive Suite 800-824 San Diego, CA 92108 (619) 286-5438 ext. 106 blaine@aclifts.com www.aclifts.com Received 2/8/17 Received 2/8/17 Received 2/8/17 37870-R3 200 S. Aspen Quotation No. Date: 24-Jan-17 Quote valid until: 23-Jun-17 Prepared by: Project: Blaine Davies Line Quantity Description 1 1 T4-269-060DL,114X242,460/3PH/60HZ,24 VDC,REMOTE 10HP, AQ GRAY Model Description: The pit mounted model T4-269-060DL is part of the American Custom Lift family which is a hydraulic scissors lift that is specifically designed for your application. The versatility of our custom designs extends past material lifting solutions for which a specialized scissor lift would be required for your lifting requirement. The unit is painted AQ GRAY. Platform: Platform size of 114 inches wide by 242 inches long with straight sides and a smooth platform surface. The platform is reinforced for minimum deflection by structural steel shapes and forms, rigidly welded. Canopy set for 110” Power Unit: Power unit as a REMOTE 10HP, wired to a primary voltage of 460/3PH/60HZ and a control voltage of 24 VDC. Power unit is UL labeled with approved components. Controls: The lift control signal consist of a SHIP LOOSE OTHER with a rating of NEMA 4- Quantity of 2. The control panel voltage is 24 VDC for the magnetic motor starter and control transformer with a rating of NEMA 1 which will be SHIP LOOSE. Specifications Voltage: 460/3PH/60HZ Raised Height: 313.5" Platform Width: 114" Platform Length: 242" Power Unit: REMOTE 10HP Ship Weight: 28,848 lbs. Capacity: 7000 lbs. Color: AQ GRAY Travel: 268.5in. Model: T4-269-060DL Speed: 119 SEC 12 FPM 2 IPS Controls: 24 VDC Lowered Height: 45" •Velocity Safety fuses are mounted on each hydraulic cylinder. •Maintenance Safety Leg is provided for safe servicing of the lift. The following options are included: •Telescoping canopy (Clear height = 102") •Rider package •Phantom safety package Accessories •ACL lifts feature lubricated for life composite bearings on all pivot points for long service life. •Axle pins are turned, ground, polished and hard chromed for extended bearing life. •Hydraulic hoses are high-pressure double wire braided for safety and extended hose life. •ACL lifts are proudly crafted entirely in the USA and are backed by the most comprehensive equipment in the industry. Features and Benefits ACL offers as standard the most comprehensive equipment warranty in the industry. Warranty Page 2 of 3 Received 2/8/17 Received 2/8/17 Received 2/8/17 37870-R3 200 S. Aspen Quotation No. Date: 24-Jan-17 Quote valid until: 23-Jun-17 Prepared by: Project: Blaine Davies This lift is designed and built in accordance with the ANSI standard MH29.1 for industrial scissors lifts. Codes Lead Times Approval Drawing Lead time: 3 Weeks Manufacturing Lead Time: 14 Weeks Price: $216,899.00 Quoted price shown does not include taxes, Duties, freight, installation - electrical or mechanical, and unloading “This quotation is expressly subject to American Custom Lifts current terms and conditions and are expressly adopted and incorporated herein by reference.” Page 3 of 3 Received 2/8/17 Received 2/8/17 Received 2/8/17 8880 Rio San Diego Suite 800-#824 San Diego, CA 92108 AMERICAN CUSTOM LIFTS STANDARD TERMS OF SALE 1. GENERAL Seller’s prices are based on these sales terms and ( i ) this document, together with any additional writings signed by Selle r, represents a final, complete and exclusive statement of the agreement between the parties and may not be modified, supplemented, explained or waived by parol evidence. Buyer’s purchase order, a course of dealing, Seller’s performance or delivery, or in any other way except in writing signed by an authorized representative of Seller, and (ii) these terms are intended to cover all activity of Seller and Buyer hereunder, including sales and use of products parts and all related matters (references to products include parts). Any references by Seller to Buyer’s specifications and similar requirements are only to describe the products covered hereby, and no warranties or other terms therein shall have any force or effect. Catalogues, circulars and similar pamphlets of the Seller are issued for general information purposes only and shall not be deemed to modify the provisions hereof. The agreement formed hereby and the language herein shall be construed and enforced under the Uniform Commercial Code as in effect in the State of Seller’s head office on the date hereof. 2. TAXES Any sales, use or other similar type taxes imposed on this sale or on this transaction are not included in the price. Such t axes shall be billed separately to the Buyer. Seller will accept a valid exemption certificate from the Buyer if applicable; however, if an exemption certificate previously accepted is not recognized by the governmental taxing authority involved and the Seller is required to pay the tax covered by such exemption certificate. Buye r agrees to promptly reimburse Seller for the taxes paid. 3 PERFORMANCE, INSPECTION AND ACCEPTANCE All products shall be finally inspected and accepted within ten (10) days after receipt at point of delivery. All claims wh atsoever by Buyer (including claims for shortages) excepting only those provided for under the WARRANTY AND LIMITATION OF LIABILITY AND PATENTS Clauses hereof must be asserted in writing by Buyer within said ten (10) day period or they are waived. If this contact involves partial performances, all claims must be asserted within said ten (10) day period for each partial performance. There shall be no revocation of acceptance. Rejection may be only for defects substantially impa iring the value of products and Buyer’s remedy for lesser defects shall be those provided for under the WARRANTY AND LIMITATION OF LIABILITY Clause. Seller shall not be responsible for nonperformance or delays in performance occasioned by any causes beyond Seller’s reasonable control, including, but not limited to labor difficulties, delays of vendors or carriers, fires, governmental actions and material shortages. Any delays so occasio ned shall effect a corresponding extension of Seller’s performance dates which are, in any event, understood to be approximate. In no event shall Buyer be entitled to incidental or consequential damages for late performance or failure to perform. If Buyer wrongfully rejects or revokes acceptance of items tendered under this agreement, or fails to make a payment due on o r before delivery, or repudiates this agreement, Seller shall have a right to recover damages as stated herein. Upon recovery of the damages, the items involved s hall become the property of the Buyer. If payment is not made upon demand and default occurs, Buyer promises to pay all costs and expenses of collection and reasonable attorney’s fees incurred by Seller hereof on account of such collection, whether or not suit is filed thereon. In any action brought under or arising out of this transaction, the Buyer, including its successors or assigns, hereby consents to the jurisdiction of any competent court within the State of California, and consent to service or process by any means authorized by California law. Seller reserves the right to modify product details not affecting application or strength, if necessary to facilitate manufacture. If Buyer fails to pay any invoice beyond terms herein stated, Seller reserves the right to charge interest at the maximum rate allowable under the law. 4. TITLE AND RISK OF LOSS Full risk of loss (including transportation delays and losses) shall pass to the Buyer upon delivery of products to the F.O.B . point. However, Seller retains title, for security purposes only, to all products until paid for in full in cash and Seller may, at Seller’s option, repossess the same, upon Buyer’s default in payment hereunder, and charge buyer with any deficiency. 5. WARRANTY AND LIMITATION OF LIABILITY Seller warrants that its products and parts, when shipped, will meet all applicable specification (unless otherwise noted in writing) and other specific product requirements (including those of performance) if any, of the agreement, will be of good quality, and will be free from defects in material and workmanship. All claims for defective products or parts under this warranty must be made in writing immediately upon discovery and, in any event, within one (1) ye ar from shipment of the applicable item. Defective items must be held for Seller’s inspection and returned to the original F.O.B. point upon request. THE FOREGOING IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES WHATSOEVER, EXPRESS, IMPLIED AND STATUTORY, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. Upon Buyer’s submission of a claim as provided above and its substantiation, Seller shall at its option either ( i ) repair or replace its product or part at the original F.O.B. point of delivery or (ii) refund an equitable portion of the purchase price. Page 1 of 2 Received 2/8/17 Received 2/8/17 Received 2/8/17 The foregoing is Seller’s only obligation and Buyer’s only remedy for breach of warranty, and except for gross negligence, willful misconduct, and remedies permitted under the PERFORMANCE, INSPECTION AND ACCEPTANCE and the PATENTS Clause hereof, the foregoing is Buyer’s only remedy hereunde r by way of breach of contract, tort or otherwise, in no event shall Buyer be entitled to incidental or consequential damages. Any action for breach o f this agreement must be commenced within two (2) years after the cause of action has accrued. BUYER FURTHER ACKNOWLEDGES THAT IT HAS CONTROL OVER THE INSTALLATION, MAINTENANCE AND OPERATION OF THE EQUIPMENT IDENTIFIED IN THIS SALES AGREEMENT, AND ACCORDINGLY AGREES: ( i ) TO PROPERLY TRAIN AND SUPERVISE ITS EMPLOYEES, AGENTS AN D OPERATORS IN THE OPERATION AND MAINTENANCE OF THE EQUIPMENT; ( ii ) TO DISCLOSE TO AND TO HAVE AVAILABLE TO ITS EMPLOYEES, AGENTS AND OPERATORS A COPY OF THE MAINTENANCE, SAFETY INSTRUCTIONS AND WARNINGS PROVIDED BY SELLER; (iii) NOT TO MODIFY, ALTER OR MISUSE THE EQUIPMENT; AND (iv) TO ACCEPT ALL RESPONSIBILITY AND LIABILITY FOR INJURY TO PERSON OR PROPERTY ARISING FROM THE REMOVAL OF SAFETY EQUIPMENT AND WARNINGS OR FROM BUYER’S DECISION NOT TO PURCHASE SAFETY EQUIPMENT RECOMMENDED BY SELLER OR ITS DISTRIBUTOR. 6. PATENTS Seller agrees to assume the defense of any suit for infringement of any United States patents brought against Buyer to the extent such suit charges infringement of an apparatus or product claim, by Seller’s product in and of itself provided ( i ) said product is built entirely to Seller’s design, (ii) Buyer notifies Seller in writing of the filing of such suit within ten (10) days after the service of process thereof, and (iii) Seller is given complete control of the defense of such suit, including the right to defend, settle and make changes in the product for the purpose of avoiding infringement. Seller assumes no responsibility for charges of infringement of any process or method claims, unless infringement of such claims is the result of following specific instructions furnished by Seller. 7. SPECIAL TOOLING Notwithstanding any tool, die or pattern charges or amortization in connection herewith, all special tooling and related item s shall be and remain the property of Seller. 8. Any clause required to be included in a contract of this type by any applicable and valid Federal, State or local law or administrative rules or regulation or order having the effect of law shall be determined to be incorporated herein. 9. PAYMENT TERMS 20% down (non-refundable) to create shop drawings. Remaining 80% due prior to shipping. Lift(s) must be accepted and paid for in full no later that four months after the date the approval drawings were signed an submitted to American Custom Lifts. Projects remaining on approval drawing status in excess of 90 days or beyond quotation validity date may require updating of quotation. Any exceptions must be agreed to in writing by American Custom Lifts. Customer is liable for storage fees if the lifts(s) is not accepted within one month from the date of completion of the lift(s) or from the date lift was originally scheduled to ship. Any exceptions must be agreed to in writing by American Custom Lifts. 10. CANCELLATION CHARGES 20% after approval drawings are prepared. 50% after signed approval drawings are submitted and materials ordered. Up to 80% after construction of the lift(s) has begun based upon work in progress to within 4 weeks of completion. 100% within 4 weeks of completion. 11. REMITTANCE INFORMATION American Custom Lift 8880 Rio San Diego Suite 800-#824 San Diego, CA 92108 U.S. Bank 1455 Frazee Rd Ste 104 San Diego, CA 92108 U.S. Bank Phone (619)278-7400 Routing Number: 122235821 Account Number: 153464373999 International Wire Transfers SWIST #USBKUS44IMT PRICES AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. PRICES U.S. DOLLARS, F.O.B. GUTHRIE, OKLAHOMA U.S.A. NOTES: Compliance to state and local codes is the responsibility of the end use Page 2 of 2 AMERICAN CUSTOM LIFTS STANDARD TERMS OF SALE (continued) Received 2/8/17 Received 2/8/17 Received 2/8/17 NO. DESCRIPTION BY CHK'D DATE 03RAS JOB NAME: DRAWN BY: DATE:REV.SIZE: DRAWING TITLE: DRAWING NUMBER:PAGE: AQJ NO: REFERENCE DRAWING:REF DRW AQJ # 20-Jan-17 1 OF 5 APPROXIMATE WEIGHT: 28,848FRACTIONS: +/- 1/4 B Aspen. CO. 200 S. AspenT O L E R A N C E S T4-269-060DL, 114X242, AQ GRAY 37870-R03 1 OF 5 CHK'D CHECKED: UNLESS OTHERWISE SPECIFIED: ALL DIMENSIONS ARE IN INCHES 37870-R03 © COPYRIGHT AUTOQUIP ALL RIGHTS RESERVED. Year of copyright is first yearindicated on this document.Received 2/8/17 Received 2/8/17 Received 2/8/17 on 4 sidesTape switch(shipped -Park assist Loose) Raised position Park assist(shipped -Loose) 268.5 Travel 242" 110" 216" Clear 103.196 Clear NO. DESCRIPTION BY CHK'D DATE UNLESS OTHERWISE SPECIFIED: B2 OF 5 JOB NAME: DRAWN BY: DATE:REV.SIZE: DRAWING TITLE: DRAWING NUMBER:PAGE: AQJ NO: 37870-R03 37870-R03 2 OF 5 REFERENCE DRAWING:REF DRW FRACTIONS: +/- 1/4 03 T4-269-060DL, 114X242, AQ GRAY 28,848 AQJ #Aspen. CO. 200 S. Aspen RAS T O L E R A N C E S ALL DIMENSIONS ARE IN INCHES CHK'D CHECKED:APPROXIMATE WEIGHT: 20-Jan-17 © COPYRIGHT AUTOQUIP ALL RIGHTS RESERVED. Year of copyright is first yearindicated on this document. Lowered position Platform mountableComand centers.(shipped loose) 242" 2" 45" 244" 268.5 Travel Received 2/8/17 Received 2/8/17 Received 2/8/17 Upper levelAutomatic door(by others) 268.5 Floor to Floor Lower level / garage 37870-R03 03B JOB NAME: DRAWN BY: DATE:REV.SIZE: DRAWING TITLE: DRAWING NUMBER:PAGE: AQJ NO: REFERENCE DRAWING:T4-269-060DL, 114X242, AQ GRAY FRACTIONS: +/- 1/4 APPROXIMATE WEIGHT: 3 OF 5 37870-R03 3 OF 5 20-Jan-1728,848 RAS Aspen. CO. 200 S. AspenT O L E R A N C E S AQJ # REF DRW CHK'D CHECKED: UNLESS OTHERWISE SPECIFIED: ALL DIMENSIONS ARE IN INCHES © COPYRIGHT AUTOQUIP ALL RIGHTS RESERVED. Year of copyright is first yearindicated on this document. Lower levelAutomatic door(by others) Floor to Floor 45" 268.5 116" Received 2/8/17 Received 2/8/17 Received 2/8/17 FRACTIONS: +/- 1/4 B JOB NAME: DRAWN BY: DATE:REV.SIZE: DRAWING TITLE: DRAWING NUMBER:PAGE: AQJ NO: REFERENCE DRAWING:T4-269-060DL, 114X242, AQ GRAY APPROXIMATE WEIGHT: 4 OF 5 37870-R03 4 OF 5 20-Jan-1728,848 RAS AQJ # Aspen. CO. 200 S. AspenT O L E R A N C E S REF DRWALL DIMENSIONS ARE IN INCHES CHK'D CHECKED: UNLESS OTHERWISE SPECIFIED: 0337870-R03 © COPYRIGHT AUTOQUIP ALL RIGHTS RESERVED. Year of copyright is first yearindicated on this document. Corner guides4 - Shipped loose 114" Platform Pit Length 244" Platform 1" 242" Pit width 116" 1" Received 2/8/17 Received 2/8/17 Received 2/8/17 ONLY INCLUDE ITEMS PERTINENT TO THE EQUIPMENT ITSELF. ATTENTION THE PURPOSE OF THIS DRAWING IS TO PROVIDE NECESSARY INFORMATION ABOUT THE EQUIPMENT SO THAT THE ARCHITECT OR INSTALLER CAN MAKE A FINAL CONSTRUCTION DRAWING FOR THE SPECIFIC JOB SITE. INSTALLATION DETAILS SUCH AS CONCRETE THICKNESS, REINFORCING, PIPING DIRECTION, CONDUIT SIZE, POWER UNIT LOCATION, ADJACENT STRUCTURES, ETC CANNOT ECONOMICALLY BE INCORPORATED IN THE MANUFACTURER'S DRAWINGS. APPROVAL OF THIS DRAWING IS AN APPROVAL OF THE EQUIPMENT ONLY. ANY REQUIRED CHANGES SHOULD REQUIREMENTS OF THE STATE AND LOCAL AUTOQUIP SCISSOR LIFTS MEET ALL DESIGN AND SAFETY REQUIREMENTS SET FORTH IN ANSI MH29.1. IT IS THE ULTIMATE RESPONSIBILITY OF THE BUYER OF THE LIFT FOR GAINING STATE AND LOCAL CODE APPROVALS. PLEASE ACQUAINT YOURSELF WITH THE PERMITTING AND/OR LICENSING EXPENSES AND REGULATORY AGENCIES IN THE INSTALLATION AREA. 80% - AFTER PURCHASE OF MATERIALS AND WITHIN (2) WEEKS OF SCHEDULED SHIP DATE CANCELLATION POLICY THIS AUTOQUIP PRODUCT IS DESIGNED AND FABRICATED TO THE ORDER. THIS IS NOT A STANDARD PRODUCTION MODEL THAT CAN BE PLACED IN STOCK FOR FUTURE SALE. CANCELLATION CHARGES 10% - AFTER APPROVAL DRAWING HAS BEEN CREATED BUT BEFORE PURCHASE OF MATERIAL SPECIFICATIONS MODEL: T4-269-060DL CAPACITIES:7,000 LBS MAX LIFTING3,500 LBS MAX END LOAD3,000 LBS MAX SIDE LOAD PLATFORM: 114W x 242L SMOOTH STEEL LOWERED HEIGHT: 45 TRAVEL: 268.5 SPEED:119 SECONDS UP90 SECONDS DOWN (LOADED) POWER UNIT: 10 HP - INTERNAL PRIMARY VOLTAGE: 460 VAC / 3 PH / 60 HZ CONTROL VOLTAGE: 24 VDC CONTROL PANEL: NEMA 4 - SHIPPED LOOSE CONTROL SIGNAL:4-Comand centers with video, key pad, key, up/dn pushbuttons, E-stop (Shipped loose) NOTES: Conceptual drawing only NOT for construction.1. •Telescoping canopy 2. •Rider package3. •Phantom safety package4. UNLESS OTHERWISE SPECIFIED: 37870-R03B JOB NAME: DRAWN BY: DATE:REV.SIZE: DRAWING TITLE: DRAWING NUMBER:PAGE: AQJ NO: FRACTIONS: +/- 1/4 REFERENCE DRAWING:T4-269-060DL, 114X242, AQ GRAY APPROXIMATE WEIGHT: 5 OF 5 37870-R03 5 OF 5 20-Jan-1728,848 AQJ #Aspen. CO. 200 S. Aspen RAS T O L E R A N C E S ALL DIMENSIONS ARE IN INCHES CHK'D CHECKED: REF DRW 03 © COPYRIGHT AUTOQUIP ALL RIGHTS RESERVED. Year of copyright is first yearindicated on this document.Received 2/8/17 Received 2/8/17 Received 2/8/17