HomeMy WebLinkAboutFile Documents.200 S Aspen St.0007.2017 (67).ACBK10
Front opening
Front and rear opening
H Inside Clear Cab Height: 7’-4” 6
X Standard Jack Hole Depth:
Travel + 6’-0”
I Entrance Height: 7’-0”O Minimum Overhead:
• Up to 100 fpm: 12’-0”
• Over 100 fpm: 12’-3”
P Pit Depth: 4’-0”S Safety Beam Required
per OSHA 1926.5027
2 In areas where a 7" deep pit ladder is required, additional hoistway width or wall pocket will be required.
3 This capacity is not available with center-opening doors.
4 To meet the requirements of IBC code for 84" stretchers, a 4'-0" center-opening (for 4000 lbs capacity
only) or 3'-6" side-opening (for 3500 lbs or 4000 lbs capacity) door is required.
6 Dimension shown is based on suspended ceiling design. An increase in cab height will result in an
increase in overhead requirements.
7 Provided and installed by others, as directed by the local thyssenkrupp office. Clear overhead is shown
to the bottom of the safety beam.
* Refer to page 12 for elevator machine room sizes.
Passenger
Cap
(lbs)
Platform
A X B
Hoistway2
C X D
Front/
rear
Inside clear
F x G
Door
type
Door
width
21003 6’-0” x 5’-1” 7’-4” x 5’-9” F 5’-8” x 4’-3” 1-SP 3’-0”
21003 6’-0” x 5’-81/4 ” 7’-4” x 6’-8
3/4 ” F/R 5’-8” x 4’-3
1/2 ” 1-SP 3’-0”
2500 7'-0" x 5'-1" 8’-4” x 5’-9” F 6’-8” x 4’-3” 1-SP 3’-6”
2500 7’-0” x 5’-8
1/4 ” 8’-4” x 6’-8
3/4 ” F/R 6’-8” x 4’-3
1/2 ” 1-SP 3’-6”
3000 7’-0” x 5’-7” 8’-4” x 6’-3” F 6’-8” x 4’-9” 1-SP 3’-6”
3000 7’-0” x 6’-2
1/4 ” 8’-4” x 7’-2
3/4 ” F/R 6’-8” x 4’-9
1/2 ” 1-SP 3’-6”
35004 7’-0” x 6’-3” 8’-4” x 6’-11” F 6’-8” x 5’-5” 1-SP 3’-6”
35004 7’-0” x 6’-101/4 ” 8’-4” x 7’-10
3/4 ” F/R 6’-8” x 5’-5
1/2 ” 1-SP 3’-6”
40004 8’-0” x 6’-3” 9’-4” x 6’-11” F 7’-8” x 5’-5” 1-SP 3’-6” / 4’-0”
40004 8’-0” x 6’-101/4 ” 9’-4” x 7’-10
3/4 ” F/R 7’-8” x 5’-5
1/2 ” 1-SP 3’-6” / 4’-0”
Below-
ground
Hydraulic with machine room
Jack types Travel Speed Capacity
Conventional 60’-0”80-200 fpm 2100-4000 lbs
Passenger elevators
Dimensional data shown above is for both seismic and non-seismic zones and complies with current ASME A17.1 and
CSA B44 Safety Code for Elevators. Local codes may vary from the national codes. Consult your thyssenkrupp Elevator
representative for details.
Platform WidthA
Inside Clear WidthF
Pit DepthP
Platform DepthB
Inside Clear DepthG
Safety BeamS
Hoistway DepthD
Entrance Height I
Clear Door OpeningE
OverheadO
TravelT
Hoistway WidthC
Inside Clear HeightH
Jack Hole DepthX
Platform WidthA
Inside Clear WidthF
Pit DepthP
Platform DepthB
Inside Clear DepthG
Safety BeamS
Hoistway DepthD
Entrance Height I
Clear Door OpeningE
OverheadO
TravelT
Hoistway WidthC
Inside Clear HeightH
Jack Hole DepthX
I
S
O
T
P
X
HI
O
T
P
H
X
I
I
S
1-SP
Side-Opening Doors
Front Opening (F)
Front & Rear Opening (F/R)
1-SP
Side-Opening Doors
DB
C
A
F
G
E
DB
C
A
F
G
E
DB
C
A
F
G
E
DB
C
A
F
G
E
1-SP
Center-Opening Doors
1-SP
Center-Opening Doors
Received
2/8/17
Received
2/8/17
12
Single-car
with dry unit
Dual-car
with dry unit
1 Clear opening.
2 Smaller machine rooms available in some cases, contact your thyssenkrupp Elevator
respresentative if needed.
Single-car configurations Dual-car configurations
Single-car2
Power unit ABCDoor height Room height
Submersible (large) 7'-2" 7'-1
1/2 " 4'-0" Min 7'-0" Min 7'-6"
Dry (large) 9'-10" 5'-6” 4'-0" Min 7'-0" Min 7'-6"
Dual car2
Power unit ABCDoor height Room height
Submersible (large) 10'-5
1/2 " 10’-5
1/2 " 4'-0"Min 7'-0" Min 7'-6"
Dry (large) 14'-7" 7’-0
3 /4 " 4'-0"Min 7'-0" Min 7'-6"
The most desirable controller closet location is on the lowest floor served, adjacent to the elevator hoistway.
At an additional cost, machine room can be located remote from hoistway.
Your endura system determines the machine room you’ll need.*
*Contact your local representative to help determine your needs, as machine room arrangments my vary from those shown.
Hydraulic elevator machine rooms
endura
Power Unit
Disconnect
Switch
(by others)
A
B
C
Power Unit
Power Unit
D
E
F
Disconnect
Switch
(by others)
Received
2/8/17
Received
2/8/17