HomeMy WebLinkAboutFile Documents.234 W Francis St.0118-2020-BRES (45) 2015 IECC REMP WORKSHEET INSTRUCTIONS
CITY OF ASPEN VERSION 113 UPDATED DECEMBER 13, 2017
As adopted by Ordinance 40, 2016
1 REMP Submittal Requirements:
* Contact a Permit Coordinator for requirements for all departments including Zoning, Parks, Utilities, and
Engineering. See the following checklists and submittal guides for building department requirements:
IRC Checklist
IRC Submittal guide
IBC Checklist
IBC Submittal guide
2 Worksheet Instructions:
* Find the appropriate worksheet in the tabs below.
(R-REMP sheet for residential)
(C-REMP sheet for commercial or 4+story residential)
* Complete the upper half of the worksheet, including the project address, permit number,
parcel ID and all contact information
* List all drawing sheets that have REMP information, such as site plans and mechanical plans.
* The building official may approve an exemption from REMP in certain cases as described in Ordinance 40, 2016.
If you have received approval for this exemption, check the 'yes' box and enter the exempt sqft portions in the
new (exempt) row.
* Enter all existing onsite snowmelt/spa/pool areas and amounts to be removed or replaced.
* Enter new square footages (snowmelt, spa and/or pool) including replaced areas.
* The intent is to document all snowmelt, spa, and pool areas on the entire site. Change orders should show the
complete picture, including previous change orders and the master permit.
* Enter the boiler efficiency being used per manufacturer specifications
Note: Boiler efficiency is a minimum of 75%. Electric
snowmelt automatically gets 100%.
* The mitigation payment due will be shown in the green-tinted box.
* If you are planning to install supplemental energy systems:
* Determine the type(s)of system and use the appropriate worksheet in the tabs below.
PV Worksheet for photovoltaic solar systems
Solar Thermal Worksheet for solar hot water systems
GSHP Cert for groundsource heat pump systems
* The mitigation credits for each system will be automatically entered into your RREMP or CREMP form. If your
project has both RREMP and CREMP, it will automatically divide the credits up, with priority given to mitigating the
CREMP payment.
* The total mitigation credits are subtracted from the total mitigation payment to give you a total REMP payment.
* If you previously paid a REMP payment as part of this project, enter the amount previously
paid. If a refund is due, it will be displayed. Note that per policy, $750 is deducted from
refunds for administrative expenses. Expires 180 days after certificate of occupancy.
2015 IECC RESIDENTIAL RENEWABLE ENERGY MITIGATION PROGRAM
CITY OF ASPEN VERSION 11,3 UPDATED DECEMBER 13, 2017
PROJECT ADDRESS: 234 W. Francis St. Aspen
Parcel ID#: 2735 - 124- 17-003 Permit Number:
CONTACT INFORMATION :
Owner:
Name: City:
Address: State:
Email: Zip Code:
Phone: Cell Phone:
Owner's Representative:
Name: Derek Skalko City: Aspen
Address: 1 FRIDAY DESIGN, PO Box 7928, State: CO
Email: derek@lfriday.com Zip Code: 81612
Phone: 970.309.0695 Cell Phone:
A. RESIDENTIAL RENEWABLE ENERGY MITIGATION PROGRAM
Sheets showing snowmelt, pool, spa, and solar/GSHP information: M0.02, M1.01, M1.02, M2.01, M2.03
Do you have snowmelt or a spa that has been exempted by the buiding official? 0 Yes(enter sqft below on the exempt row) @ No
Hydro Snowmelt Electric Snowmelt Pool Spa
Existing
To be Demoed
Existing to Remain 0.00 sqft 0.00 sqft 0.00 sqft 0.00 sqft
New(non-exempt) 1015.00 sqft 56.00 sqft
New(exempt)
Total New 1015.00 sqft 0.00 sqft 0.00 sqft 56.00 sqft J
Total on site 1015.00 sqft 0.00 sqft 0.00 sqft 56.00 sqft
Total Snowmelt on site 1015.00 sqft
Boiler Efficiency 95.0% I 100% 75.0% 95.0%
Mitigation Payment $36,326.32 $ - $ 10,374.74
Total Payment for Mitigation: $ 46,701.05
B. ON-SITE RENEWABLE CREDITS
Supplemental System REMP Credit
Use PV Worksheet Photovoltaic System $ 35,436.79
Use Thermal Worksheet Hot Water Panels $Use GSHP Cert Ground Source Heat Pump $ -
Other Approved System $ -
RECEIVED Total Mitigation Credits: $ 35,436.79
Onsite Renewable Offsets: How many Kilo Watts of PV(solar electric)would I need? 6.80
or How many square feet of SHW(solar hot water)would I need? 207.88
02/10/2022
R-REMP Payment: $ 11,264.26
ASPEN Amount Previously Paid on This Permit:
BUILDING DEPARTMENT I TOTAL R-REMP PAYMENT: $ 11,264.26
Refund (includes minus$750): $ -
C. PREPARED BY: Date: 12/2/2021
Print Name: Dodson Harper, PE
Signature: gdodsonharper
Phone& EMail: 970.349.1216, dodson@reginc.com
REVIEWED: Date:
2015 IECC COMMERCIAL RENEWABLE ENERGY MITIGATION PROGRAM
CITY OF ASPEN VERSION 1,1,3 UPDATED DECTMB'E.7 13, 2017
PROJECT ADDRESS:
Parcel ID#: Permit Number:
CONTACT INFORMATION :
Owner:
Name: City:
Address: State:
Email: Zip Code:
Phone: Cell Phone:
Owner's Representative:
Name: City:
Address: State:
Email: Zip Code:
Phone: Cell Phone:
A. COMMERCIAL RENEWABLE ENERGY MITIGATION PROGRAM
Sheets showing snowmelt, pool, spa, and solar/GSHP information:
Do you have snowmelt or a spa that has been exempted by the buiding official? 0 Yes(enter sqft below on the exempt row) 0 No
Hydro Snowmelt Electric Snowmelt Pool Spa
Existing
To be Demoed
Existing to Remain 0.00 sqft 0.00 sqft 0.00 sqft 0.00 sqft
New(non-exempt)
New(exempt)
Total New 0.00 sqft 0.00 sqft 0.00 sqft 0.00 sqft
Total on site 0.00 sqft 0.00 sqft 0.00 sqft 0.00 sqft
Total Snowmelt on site 0.00 sqft
Boiler Efficiency 75.0% 100% 75.0% 75.0%
Mitigation Payment $0.00 $ - $ -
Total Payment for Mitigation: $0.00
B. ON-SITE RENEWABLE CREDITS
Supplemental System REMP Credit
Use PV Worksheet Photovoltaic System $Use Thermal Worksheet Hot Water Panels $Use GSHP Cert Ground Source Heat Pump $ -
Other Approved System $ -
Total Mitigation Credits: $ -
Onsite Renewable Offsets: How many Kilo Watts of PV(solar electric)would I need? 0.00
or How many square feet of SHW(solar hot water)would I need? 0.00
C-REMP Payment: $ -
Amount Previously Paid on This Permit: $ -
TOTAL C-REMP PAYMENT: $ -
Refund (includes minus$750): $C. PREPARED BY: Date:
Print Name:
Signature:
Phone&EMail:
REVIEWED: Date:
PV WORKSHEET
CITY OF ASPEN VERSION 11.5 UPDATED MAY 14,2021
PROJECT ADDRESS: 234 West Francis,Aspen CO 81611
Parcel ID#: 2735-124-17-003 Permit Number:
Collector Solar
Aspect,Degrees Collector Tilt, Orientation
from True South Degrees From Adjustment DC side capacity Inverter capacity kW for kW Mitigation
Horizontal Factor (kW) (kW) credit Credit
Collector Group 1 15 0 87.00% 6.55 5.933 5.933 5.16 kW
Collector Group 2 87.00% 0 0.00 kW
Collector Group 3 87.00% 0 0.00 kW
Collector Group 4 87.00% 0 0.00 kW
Collector Group 5 87.00% 0 0.00 kW
Collector Group 6 87.00% 0 0.00 kW
Collector Group 7 87.00% 0 0.00 kW
Collector Group 8 87.00% 0 0.00 kW
Collector Group 9 87.00% 0 0.00 kW
Collector Group 10 87.00% 0 0.00 kW
Collector Group 11 87.00% 0 0.00 kW
Collector Group 12 87.00% 0 0.00 kW
Collector Group 13 87.00% 0 0.00 kW
Collector Group 14 87.00% 0 0.00 kW
Collector Group 15 87.00% 0 0.00 kW
Collector Group 16 87.00% 0 0.00 kW
Collector Group 17 87.00% 0 0.00 kW
Collector Group 18 87.00% 0 0.00 kW
Collector Group 19 87.00% 0 0.00 kW
Collector Group 20 87.00% 0 0.00 kW
Total: 5.16 kW
$Mitigation Credit: $ 35,436.79
Instructions:
1) Determine how many collector groups you have.Groups are used to differentiate between collectors
(panels)with different tilts,aspects,sizing,or inverters. If all your collectors are installed similarily,you
might have just one group.
2) Enter the aspect and tilt for each group.The solar orientation adjustment factor is automatically
calculated.
3) DC side capacity is the total labled panel output kW in a group.
4) Inverter capacity is the recommended output power in kW of your inverter(s).
5) You will be given credit for the lesser of the labeled panel output or the inverter.
6) The kW for credit is multiplied by the solar orientation adjustment factor to get kW mitigation credit.
7) The kW mitigation credit is totalled and multiplied by$6865.32/kW to get the$Mitigation Credit
8) The mitigation credit will be automatically entered into your RREMP or CREMP form. If your project has both RREMP and
CREMP,it will automatically divide the credits up,with priority given to mitigating the CREMP payment.
PREPARED BY: Date: 12/2/2021
Print Name: Greg Peterson
Signature: Greg K Peterson
Phone&EMail: 970.963.1420; greg@sunsensesolar.com
REVIEWED: Date:
RECEIVE _,
02/10/2022
ASPEN
BUILDING DEPARTMENT
SOLAR THERMAL WORKSHEET
CITY OF ASPEN VERSION 11.3 UPDATED DECEA BER 13, 2017
PROJECT ADDRESS:
Parcel ID#: Permit Number:
Collector Solar
Aspect, Collector Tilt, Orientation
Degress from Degrees From Adjustment Square feet of Sqft Mitigation
True South Horizontal Factor collectors Credit
Collector Group 1 87.00% 0.00 sqft
Collector Group 2 87.00% 0.00 sqft
Collector Group 3 87.00% 0.00 sqft
Collector Group 4 87.00% 0.00 sqft
Collector Group 5 87.00% 0.00 sqft
Collector Group 6 87.00% 0.00 sqft
Collector Group 7 87.00% 0.00 sqft
Collector Group 8 87.00% 0.00 sqft
Collector Group 9 87.00% 0.00 sqft
Collector Group 10 87.00% 0.00 sqft
Collector Group 11 87.00% 0.00 sqft
Collector Group 12 87.00% 0.00 sqft
Collector Group 13 87.00% 0.00 sqft
Collector Group 14 87.00% 0.00 sqft
Collector Group 15 87.00% 0.00 sqft
Collector Group 16 87.00% 0.00 sqft
Collector Group 17 87.00% 0.00 sqft
Collector Group 18 87.00% 0.00 sqft
Collector Group 19 87.00% 0.00 sqft
Collector Group 20 87.00% 0.00 sqft
Total: 0.00 sqft
$ Mitigation Credit: $ -
Instructions:
1) Determine how many collector groups you have. Groups are used to differentiate between collectors
(panels)with different tilts, aspects, sizing, or inverters. If all your collectors are installed similarily, you
might have just one group.
2) Enter the aspect and tilt for each group. The solar orientation adjustment factor is automatically
calculated.
3) Enter the square the total panel square footage in each group.
4) The square footage is multiplied by the solar orientation adjustment factor to get Sqft mitigation credit.
5) The kW mitigation credit is totalled and multiplied by$224.65/sqft to get the $ Mitigation Credit
6) The mitigation credit will be automatically entered into your RREMP or CREMP form. If your project has both RREMP and
CREMP, it will automatically divide the credits up, with priority given to mitigating the CREMP payment.
PREPARED BY: Date:
Print Name:
Signature:
Phone& EMail:
REVIEWED: Date:
GROUND SOURCE HEAT PUMP SOURCE CERTIFICATION
CITY OF ASPEN VERSION 11.3 UPDATED DECEMEER 13, 2017
Project Address:
Parcel ID#: Permit Number:
All Ground Source Heat Pump systems must be certified prior to installation;
please provide all the required information as part of your application.
I. Please list the following information
BTUs per hour of installed GSHP:
$ Mitigation Credit: $ -
Agency
Designer Certification: AEE CGD Number:
Installer Accreditation: IGSHPA Number:
Division of Water Resources Permit:
II. GSHP System Design Specifications
Number of Loops:
Depth of Loops: ft.
Total Loop Length: ft.
Total System Capacity @ 32 °F EWT: tons
ARI 330 or ISO 13256-1System Performance: COP
Coefficient of Performance of the system must be at least 3 as per American Research
Institute Standard performance method (ARI 330)or ISO 13256-1 for closed loop earth-
coupled heat pump systems (for hydronic systems use an output temperature of 115
degrees F)or equivalent procedure.
III. Attach the following information with application.
A. GSHP unit performance sheets certified by ARI 330 or ISO 13256-1.
B. Designer Certification Sheets
C. Installer Certification Sheets
D. Division of Water Resource Permit
NOTE: A GSHP is an energy-efficient option that significantly reduces energy use and
minimizes REMP payments. The REMP payment associated with a GSHP is used to offset
the coal powered electricity over 20 years. This option is calculated on REMP summary
sheet.
IV. PREPARED BY: Date:
Print Name:
Signature:
Phone&EMail:
REVIEWED: Date:
Collector Tilt,Degrees From Horizontal
0 10 20 30 40 50 60 I 70 80 I 90
0 87.00% 93.20% 97.60% 99.90% 100% 98.00% 93.90% 87.80% 80.00% 70.70%
10 87.00% 93.10% 97.40% 99.70% 99.80% 97.70% 93.60% 87.60% 79.90% 70.70%
Collector 20 87.00% 92.80% 96.90% 99.00% 99.10% 97.10% 93.00% 87.10% 79.60% 70.70%
Aspect 30 87.00% 92.40% 96.10% 98.00% 97.90% 95.90% 92.00% 86.20% 79.00% 70.50%
Degrees 40 87.00% 91.80% 95.00% 96.60% 96.40% 94.30% 90.50% 85.00% 78.10% 70.00%
From 50 87.00% 91.00% 93.70% 94.80% 94.30% 92.20% 88.50% 83.20% 76.70% 69.10%
TRUE 60 87.00% 90.00% 92.00% 92.70% 91.90% 89.60% 86.00% 80.90% 74.70% 67.60%
South 70 87.00% 89.00% 90.10% 90.20% 89.00% 86.60% 82.90% 78.10% 72.20% 65.50%
80 87.00% 87.90% 88.10% 87.40% 85.70% 83.00% 79.30% 74.60% 69.10% 62.80%
90 87.00% 86.70% 85.80% 84.30% 82.10% 79.10% 75.20% 70.60% 65.30% 59.50%
100 87.00% 85.16% 83.08% 80.70% 77.88% 74.62% 70.74% 66.45% 61.63% 56.43%_
110 87.00% 83.57% 80.18% 76.79% 73.30% 69.69% 65.70% 61.65% 57.23% 52.60%_
120 87.00% 81.83% 77.01% 72.52% 68.29% 64.29% 60.18% 56.36% 52.35% 48.32%
130 87.00% 79.95% 73.58% 67.90% 62.85% 58.42% 54.15% 50.58% 47.00% 43.60%_
140 87.00% 77.93% 69.89% 62.91% 56.99% 52.08% 47.63% 44.31% 41.19% 38.44%_
150 87.00% 75.77% 65.93% 57.57% 50.69% 45.27% 40.62% 37.56% 34.89% 32.83%_
160 87.00% 73.46% 61.71% 51.86% 43.96% 37.98% 33.10% 30.31% 28.13% 26.78%
170 87.00% 71.02% 57.23% 45.80% 36.80% 30.23% 25.10% 22.58% 20.90% 20.28%_
180 87.00% 68.43% 52.49% 39.37% 29.22% 22.00% 16.59% 14.36% 13.19% 13.34%
Efficiency°bioased on aspect and tilt
100.00% ••••••-•-• •.... ..... - 20
I
• ,,..,, • '""•.., -
! t r • • ; ; �' ' '••J=: • • • • • • • •
I
•...
90.00%
''+.. ., sa .•
80.00% •. ♦ •.............• •.... ••''••.,+• j6' •., • • ' + •.••••..,
•............. ..... • Roly.(0) •., •
•.... :•.,:: Poly.( )., •, ••+•., ... •...
o •.............* •............. •,•Poly, 0) •• '••• . •
•
70.00
....... ':/... •. Poly.(30) • •
•
• .• IF Poly.(,) •, • S.
•.
+.., Poly.(SO) •.
60.00% Po1v:.421 ••,
• • •. ▪'lbPoly.(70) ,••
Poly.(80)
Poly.(90) ''••. •.•• "0.
50.00% • •
•` R
. V.
*. •�
40.00% ~'• • • • -
▪ •
30.00% ••
•:
••.
20.00% i:•.'
10.00%
0 20 40 60 80 100 120 140 160 180