Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
File Documents.234 W Francis St.0118-2020-BRES (63)
FL4ME OUT FIRE PROTECTION 970-927-4933 Fire Suppression Supplement Material Submittal **The items listed herein are the proposed equipment to be used on this project, however we reserve the right to use an'equivalent'or manufacturer at our discretion 10/22/2020 ASPEN BUILDING DEPARTMENT Vico Worldwide www.tyco-fire.com Fire Protection Contacts Products RAPID RESPONSE Series LFII Residential 4.9 K-factor Concealed Pendent Sprinkler Flat Plate, Wet Pipe and Dry Pipe Systems General The Series LFII Residential Concealed Pendent Sprinklers (TY3596) has Description been designed with heat sensitivity and water distribution characteristics TYCO RAPID RESPONSE Series LFII proven to help in the control of residen- Residential 4.9K Concealed Pendent tial fires and to improve the chance for Sprinklers (TY3596) are decorative, occupants to escape or be evacuated. fast response,fusible solder sprinklers The Series LFII Residential Con- designed for use in residential occu- cealed Pendent Sprinklers (TY3596) pancies such as homes, apartments, are shipped with a Disposable Pro- dormitories,and hotels. tective Cap. The Protective Cap is The cover plate assembly conceals temporarily removed for installation, the sprinkler operating components and then it can be replaced to help above the ceiling.The flat profile of the Protect the sprinkler while the ceiling NOTICE cover plate provides the optimum aes is being installed or finished.The tip of thetically appealing sprinkler design. the Protective Cap can also be used The Series LFII Residential Concealed In addition, the concealed design of to mark the center of the ceiling hole Pendent Sprinklers(TY3596)described the Series LFII Residential Concealed into plaster board, ceiling tiles, etc. herein must be installed and main- Pendent Sprinklers (TY3596) provides by gently pushing the ceiling product tained in compliance with this docu- 1/2 inch(12,7 mm)vertical adjustment. against the Protective Cap. When the ment and with the applicable standards This adjustment provides a measure of ceiling installation is complete the Pro- of the National Fire Protection Associa- flexibility when cutting fixed sprinkler tective Cap is removed and the Cover tion(NFPA),in addition to the standards drops. Plate Assembly installed. of any authorities having jurisdiction. The Series LFII Residential Concealed Dry Pipe System Application Failure so may impair the perfor- mance o of t thhese devices. Sprinklers are intended for use in the The Series LFII Residential Concealed following scenarios: Pendent Sprinklers offers a laboratory The owner is responsible for main- approved option for designing dry pipe taining their fire protection system • wet and dry pipe residential sprin- residential sprinkler systems,whereas, and devices in proper operating con- kler systems for one- and two-fam- most residential sprinklers are labora- dition. Contact the installing contrar- ily dwellings and mobile homes per tory approved for wet systems only. tor or product manufacturer with any NFPA 13D questions. Through extensive testing, it has been • wet and dry pipe residential sprinkler determined that the number of design systems for residential occupancies sprinklers (hydraulic design area) for Sprinkler up to and including four stories in the Series LFII Residential Concealed height per NFPA 13R Pendent Sprinklers (TY3596) need Identification • wet and dry pipe sprinkler systems not be increased over the number of r a residentialryipeinklerof any design sprinklers (hydraulic design Number (SIN) forthe occupancy per NFPA portions3 area)as specified for wet pipe sprinkler systems,as is accustomed for density/ TY3596 area sprinkler systems designed per NFPA 13. Consequently,the Series LFII Residen- tial Concealed Pendent Sprinklers offer the features of non-water filled pipe in IMPORTANT addition to not having to increase the Always refer to Technical Data number of design sprinklers(hydraulic Sheet TFP700 for the "INSTALLER design area) for systems designed to WARNING" that provides cautions NFPA 13,13D,or 13R. with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause ��'�V/� it to operate prematurely. RE C Page 1 of 6 FEBRUARY 2015 71F910g2/2 0 2 0 ASPEN BUILDING DEPARTMENT TFP442 Page 2 of 6 BODY SEALING WRENCH (1/2"NPT) -----___--_ _-�- ASSEMBLY RECESS I i----_ / CAP 44 SPRINKLER WRENCHING ��- r I AREA SADDLE ( T SUPPORT ( \---Thr------6, COMPRESSION PUSH WRENCH CUP WITH I ENGAGEMENT SCREW IN TO ENSURE ROLL FORMED I THREADS WITH SPRINKLER WRENCHING AREA LEVER FIGURE 2 W-TYPE 18 GUIDE I SPRINKLER WRENCH PIN / SOLDER LINK / I / I ELEMENT GUIDE PIN HOUSING 1 I i DEFLECTOR_ ----,_ I I - (OPERATED DEFLECTOR -% POSITION) SPRINKLER/SUPPORT CUP ASSEMBLY THREAD INTO RETAINER SUPPORT �I WITH THREAD CUP UNTIL fJJ DIMPLES MOUNTING SURFACE IS FLUSH WITH CEILING EJECTION SPRING SOLDER COVER PLATE/RETAINER - COVER TAB ASSEMBLY PLATE FIGURE 1 RAPID RESPONSE SERIES LFII RESIDENTIAL CONCEALED PENDENT SPRINKLER(TY3596) 2-1/2"DIA. SPRINKLER- (63,5 mm) - 1/2"(12,7 mm) FACE OF SUPPORT CUP 1/2" THREADED SPRINKLER ASSEMBLY NPT ADJUSTMENT FITTING / OPERATED / SPRINKLER _ 1 \- Il 1-7/8"±1/4" PLATE f - (47,6 mm RETAINER 1 1/8"GAP ±6,4 mm) [' ,� (3,2 mm) COVER- SPRINKLER- 1 l 7/8"(22,2 mm) MOUNTING 1-1/8" 28,6 mm) RETAINER SUPPORT CUP 3/16' 1 SURFACE ` ( � ASSEMBLY ASSEMBLY (4,8 mm) I 3-3/16"DIA. DISPOSABLE DEFLECTOR IN (81,0 mm) TIP PROTECTIVE CAP OPERATED POSITION FIGURE 3 RAPID RESPONSE D INSTALLATION DIMENSIONS/PROTECTIVE CAP/ACTIVATED TDEFLECTOR SPRINKLER(TY3596�� I�� 10/22/2020 ASPEN BUILDING DEPARTMENT TFP442 Page 3 of 6 Technical Design Criteria Dry Pipe System Water Delivery When using the Series LFII Residen- Data TYCO RAPID RESPONSE Series LFII tial Concealed Pendent Sprinklers Residential Concealed Pendent Sprin (TY3596)in dry pipe sprinkler systems, Approvals klers(TY3596)are UL and C-UL Listed the time for water delivery must not exceed 15 seconds for the most remote UL and C-UL Listed NYC Approved under MEA 44-03-E-2NSF for installation in accordance with this operating sprinkler. Certified to NSF/ANSI 61 section. Note: When conditions exist that are Obstruction to The TYCO RAPID RESPONSE Series LFII Water Distribution Residential Concealed Pendent Sprinklers outside the scope of the provided cri S rinklers are to be located in accor are only Listed with the Series LFII Con- teria, refer to the Residential Sprinkler dance with the obstruction rules of cealed Cover Plates having a factory-ap- Design Guide TFP490 for the manu- plied finish. facturer's recommendations that may NFPA 13D, 13R, and 13 as applicable Cover Plates can be ordered by following be acceptable to the authority having for residential sprinklers as well as with the instructions in the Ordering Procedure jurisdiction. the obstruction criteria described within section. the Technical Data Sheet TFP490. Pressure System Types Maximum Working Per the UL Listing, wet pipe and dry Operational Sensitivity pipe systems may be utilized. Per the The sprinklers are to be installed rela Discharge Coefficient C-UL Listing, only wet pipe systems tive to the ceiling mounting surface as K=4.9 gpm/psi (70,6 Ipm/bar112) may be utilized. shown in Figure 3. Temperature Rating Refer to Technical Data Sheet TFP485 Sprinkler Spacing 160'F(71'C)Sprinkler with about the use of residential sprinklers in The minimum spacing between sprin- 139'F(59'C)Cover Plate residential dry pipe systems. klers is 8 feet (2,4 m). The maximum Vertical Adjustment spacing between sprinklers cannot 1/2 inch(12,7 mm) Ceiling Types Smooth flat horizontal, or beamed, or exceed the length of the coverage area Finishes sloped, in accordance with the 2013 (Ref. Table A or B) being hydraulically Refer to Ordering Procedure section. Edition of NFPA 13D, 13R, or 13 as calculated(e.g.,maximum 12 feet for a Physical Characteristics applicable. 12 ft.x 12 ft.coverage area, or 20 feet Body Brass for a 20 ft.x 20 ft. coverage area). Cap Bronze Hydraulic Design The Series LFII must not be used Saddle Brass (NFPA 13D and 13R) in applications where the air ores- Sealing Assembly Beryllium Nickel For systems designed to NFPA 13D sure above the ceiling is greater than w/TEFLON or NFPA 13R, the minimum required that below. Down drafts through the Soldered Link Halves Nickel sprinkler flow rates are given in Support Cup could delay sprinkler Lever Bronze Tables A and B as a function of tern- Compression Screw Brass perature rating and the maximum operation in a fire situation. Deflector Copper or allowable coverage areas. The Brass sprinkler flow rate is the minimum Guide Pin Housing Bronze required discharge from each of the Guide Pins Stainless Steel total number of"design sprinklers" as or Bronze specified in NFPA 13D or NFPA 13R. Support Cup Steel The number of "design sprinklers" Cover Plate Copper specified in NFPA 13D and 13R for wet Retainer Brass pipe systems is to be applied when Cover Plate designing dry pipe systems. Ejection Spring Stainless Steel Hydraulic Design Operation (NFPA 13) For systems designed to NFPA 13,the When exposed to heat from a fire,the number of design sprinklers Is to be Cover Plate,which is normally soldered the four most hydraulically demanding to the Support Cup at three points,falls sprinklers.The minimum required dis- away to expose the sprinkler assembly. charge from each of the four sprinklers At this point the Deflector supported by is to a the greater of the following: the Arms drops down to its operated • the flow rates given in Tables A and position. The fusible link of the sprin- B as a function of temperature rat- kler assembly is comprised of two link ing and the maximum allowable cov- halves that are soldered together with erage area a thin layer of solder. When the rated • a minimum discharge of temperature is reached, the solder 0.1 gpm/ft.2 over the design area melts and the two link halves separate comprised of the four (4) most allowing the sprinkler to activate and hydraulically demanding sprinklers flow water. for actual coverage areas protected by the four(4)sprinklers The number of design sprinklers speci- fied in NFPA 13 for wet pipe systems is to be applied when designing dry pipe systems. RECEIVED 10/22/2020 ASPEN BUILDING DEPARTMENT TFP442 Page 4 of 6 WET PIPE SYSTEM Minimum Flow and Residual Pressure" Maximum Maximum Coverage Spacing Ordinary Temp.Rating Minimum Area Ft. 160°F(71°C) Ft.x Ft. Ft.(m) Flow Pressure Deflector to Installation Spacing (m x m) Ceiling Type Ft. gpm psi (m) (Ipm) (bar) 12 x 12 12 13 7.0 Smooth (3,7 x 3,7) (3,7) (49,2) (0,48) Ceilings • 7/8 to 1-1/8 14 x 14 14 13 7.0 inches (4,3 x 4,3) (4,3) (49,2) (0,48) Beamed 16 x 16 16 13 7.0 Ceilings per 8 (4,9 x 4,9) (4,9) (49,2) (0,48) NFPA 13D or Concealed (2,4) 13R,or 13. Installed in 18 x 18 18 17 12.0 beam (5,5 x 5,5) (5,5) (64,3) (0,83) 7/8 to 1-1/8 inches below 20 x 20 20 20 16.7 bottom of (6,1 x 6,1) (6,1) (75,7) (1,15) beam Notes: 1 For coverage area dimensions less than or between those indicated,use the minimum required flow for the next highest coverage area for which hydraulic design criteria are stated 2. Requirement is based on minimum flow in gpm ppm)from each sprinkler.The associated residual pressures are calculated using the nominal K-factor Refer to Hydraulic Design under the Design Criteria section. 3. For NFPA 13 residential applications,the greater of 0 1 gpm/ft.2 over the design area or the flow in accordance with the criteria in this fable must be used. TABLE A WET PIPE SYSTEM SERIES LFII RESIDENTIAL 4.9 K-FACTOR FLAT PLATE CONCEALED PENDENT SPRINKLER(TY3596) NFPA 13D, 13R,AND 13 HYDRAULIC DESIGN CRITERIA DRY PIPE SYSTEM Minimum Flow and Residual Pressure 2,3 Maximum Maximum Coverage Spacing Ordinary Temp.Rating Minimum Area Ft. 160°F(71°C) Ft.x Ft. (m) Flow Pressure Deflector to Installation Spacing (m x m) Ceiling Type Ft. gpm psi (m) (Wm) (bar) 12 x 12 12 13 7.0 Smooth (3,7 x 3,7) (3,7) (49,2) (0,48) Ceilings 7/8 to 1-1/8 14 x 14 14 14 8.2 inches (4,3 x 4,3) (4,3) (53,0) (0,57) Beamed 16 x 16 16 15 9.4 Ceilings per 8 (4,9 x 4,9) (4,9) (56,8 NFPA 13D or Concealed (0,65) 13R,or 13. (2,4) Installed in 18 x 18 18 18 13.5 beam (5,5 x 5,5) (5,5) (68,1) (0,93) 7/8 to 1-1/8 inches below 20 x 20 20 21 18.4 bottom of (6,1 x 6,1) (6,1) (79,5) (1,27) beam Notes: 1 For coverage area dimensions less than or between those indicated,use the minimum required flow for the next highest coverage area for which hydraulic design criteria are stated. 2. Requirement is based on memmum flow in gpm ttpm)from each sprinkler.The associated residual pressures are calculated using the nominal K-factor Refer to Hydraulic Design under the Design Criteria section 3. For NFPA 13 residential applications.the greater of 0.1 gpm/ft.•over the design area or the flow in accordance with the criteria in this tnhle mist he'wed TABLE B DRY PIPE SYSTEM RAPID RESPONSE SERIES LFII RESIDENTIAL 4.9 K-FACTOR FLAT PLATE CONCEALED PENDENT(TY3596) NFPA 13D, 13R,AND 13 HYDRAULIC DESIGN CRITERIA RECEIVED 10/22/2020 ASPEN BUILDING DEPARTMENT TFP442 Page 5 of 6 Installation Step 6. Screw on the Cover Plate Care must be exercised to avoid Assembly until its flange comes in damage before,during,and after instal- TYCO RAPID RESPONSE Series LFII contact with the ceiling. lation. Sprinklers damaged by drop- Residential Concealed Pendent Sprin- Do not continue to screw on the Cover ping, striking, wrench twist/slippage, klers (TY3596) must be installed in Plate Assembly such that it lifts a or the like, must be replaced. accordance with this section. ceiling panel out of its normal position. The owner is responsible for the General Instructions If the Cover Plate Assembly cannot inspection,testing,and maintenance of Damage to the fusible Link Assembly be engaged with the Mounting Cup their fire protection system and devices during installation can be avoided by or the Cover Plate Assembly cannot in compliance with this document, as handling the sprinkler by the support be engaged sufficiently to contact the well as with the applicable standards cup only(i.e.,do not apply pressure to ceiling, the Sprinkler Fitting must be of the National Fire Protection Asst the fusible Link Assembly). repositioned. ciation (e.g., NFPA 25), in addition to the standards of any other authorities A 1/2 inch NPT sprinkler joint should be Care and having jurisdiction.Contact the install- obtained with a minimum to maximum ing contractor or product manufacturer torque of 7 to 14 lbs.-ft.(9,5 to 19,0 Nm). with any questions. Higher levels of torque may distort the Maintenance The owner must assure that the sprin- sprinkler inlet with consequent leakage TYCO RAPID RESPONSE Series LFII klers are not used for hanging any or impairment of the sprinkler. Residential Concealed Pendent Sprin- objects and that the sprinklers are only Do not attempt to compensate for klers (TY3596) must be maintained cleaned by means of gently dusting insufficient adjustment in the Cover and serviced in accordance with this with a feather duster; otherwise, non- Plate / Retainer Assembly by under- section. operation in the event of a fire or inad- or over-tightening the Sprinkler. Read- vertent operation may result. just the position of the sprinkler fitting Before closing a fire protection system to suit. main control valve for maintenance Automatic sprinkler systems should be work on the fire protection system inspected,tested,and maintained by a Step 1. The sprinkler must only be which it controls, permission to shut qualified Inspection Service in accor- installed in the pendent position and down the affected fire protection dance with local requirements and/or with the centerline of the sprinkler per- system must be obtained from the national codes. pendicular to the mounting surface. proper authorities and all personnel Step 2. Remove the Protective Cap. who may be affected by this action must be notified. Step 3. With pipe thread sealant Absence of a Cover Plate may delay the applied to the pipe threads, and using sprinkler operation in a fire situation. the W-Type 18 Wrench shown in Figure 2, install and tighten the Sprinkler / When properly installed, there is a Support Cup Assembly into the fitting. nominal 1/8 inch (3,2 mm) air gap The W-Type 18 Wrench will accept a between the lip of the Cover Plate and 1/2 inch ratchet drive. the ceiling, as shown in Figure 3. This Step 4.Replace the Protective Cap by air gap is necessary for proper opera- pushing it upwards until it bottoms out tion of the sprinkler by allowing heat against the Support Cup. The Protec flow from a fire to pass below and tive Cap helps prevent damage to the above the Cover Plate to help assure Deflector and Guide Pins during ceiling appropriate release of the Cover Plate installation and/or during application of in a fire situation. If the ceiling is to be the finish coating of the ceiling. It may repainted after the installation of the also be used to locate the center of the Sprinkler, care must be exercised to clearance hole by gently pushing the ensure that the new paint does not seal ceiling material against the center point off any of the air gap. of the Cap. Factory painted Cover Plates must not Note: As long as the protective Cap be repainted.They should be replaced, remains in place, the system is consid- necessary, by factory painted ered to be"Out Of Service." units. Non-factory applied paint may adversely delay or prevent sprinkler Step 5. After the ceiling has been operation in the event of a fire. completed with the 2-1/2 inch(63 mm) Do not pull the Cover Plate relative to diameter clearance hole and in prep- the Enclosure.Separation may result. aration for installing the Cover Plate Assembly,remove and discard the Pro- Sprinklers which are found to be tective Cap,and verify that the Deflec- leaking or exhibiting visible signs of tor moves up and down freely. corrosion must he replaced. If the sprinkler has been damaged and Automatic sprinklers must never be the Deflector does not move up and painted, plated, coated, or otherwise down freely,replace the entire sprinkler altered after leaving the factory. Modi- assembly. Do not attempt to modify or fied or over heated sprinklers must be repair a damaged sprinkler. replaced. 10/22/2020 ASPEN BUILDING DEPARTMENT TFP442 Page 6 of 6 Limited Ordering Warranty Procedure For warranty terms and conditions,visit Contact your local distributor for www.tyco-fire.com. availability. When placing an order, indicate the full product name and part number(P/N). Sprinkler Assemblies Specify: Series LFII (TY3596) 4.9K Residential Concealed Pendent Sprin- kler without Cover Plate Assembly, P/N 51-112-1-160 Cover Plate Assemblies Specify: Cover Plate Assembly with (specify) finish for the Series LFII (TY3596) 4.9K Residential Concealed Pendent Sprinkler, P/N(specify): Ivory(RAL1015) P/N 56-202-0-135 Beige(RAL1001) P/N 56-202-2-135 Pure White`(RAL9010) P/N 56-202-3-135 Signal White"(RAL9003) P/N 56-202-4-135 Grey White(RAL9002) P/N 56-202-5-135 Brown(RAL8028) P/N 56-202-6-135 Black(RAL9005) P/N 56-202-7-135 Brushed Brass P/N 56-202-8-135 Brushed Chrome P/N 56-202-9-135 Custom Paint P/N 56-202-X-135 Eastern Hemisphere sales only "Previously known as Bright White Note: All Custom Cover Plates are painted using Sherwin Williams Interior Latex Paint. Contact Tyco Customer Service with any questions related to custom orders. Sprinkler Wrench Specify: W-Type 18 Sprinkler Wrench, P/N 56-000-1-265 GLOBAL HEADQUARTERS 11400 Pennbrook Parkway,Lansdale,PA 19446 I Telephone+1-215-362-0700 Copyright©2015 Tyco Fire Products,LP. All rights reserved. lt/CO 1 0/2 2/2 0 2 0 rt.TEFLON is trademark of The DuPont Corporation Fore Protection Products ASPEN BUILDING DEPARTMENT VicoWorldwide www.tyco-fire.com Fire Protection Contacts Products RAPID RESPONSE Series LFII Residential 4.9 K-factor Pendent Sprinkler Wet Pipe and Dry Pipe Systems General Escutcheon reduces the accuracy to which the pipe drops to the sprinklers Description must be cut. The Series LFII Residential Sprinklers TYCO RAPID RESPONSE Series have been designed with heat sensi- _ LFII Residential 4.9K Pendent and tivity and water distribution charac- Recessed Pendent Sprinklers(TY2234) teristics proven to help in the control are decorative, fast response, frangi- of residential fires and to improve the x ble bulb sprinklers designed for use chance for occupants to escape or be in residential occupancies such as evacuated. homes, apartments, dormitories, and Dry Pipe System Application T hotels.When aesthetics and optimized The Series LFII Residential Pendent flow characteristics are the major con and Recessed Pendent Sprinklers sideration, the Series LFII Residential offers a laboratory approved option NSE� Sprinklers(TY2234)should be the first for designing dry pipe residential sprin- choice. kler systems,whereas,most residential NI,ON LI The Series LFII Residential Sprinklers sprinklers are laboratory approved for are intended for use in the following wet systems only. Sprinkler scenarios: Through extensive testing, it has been • wet and dry pipe residential sprin- determined that the number of design Identification kler systems for one- and two-fam- sprinklers (hydraulic design area) for ily dwellings and mobile homes per the Series LFII Residential Pendent and Number (SIN) NFPA 13D Recessed Pendent Sprinklers(TY2234) • wet and dry pipe residential sprinkler need not be increased over the number TY2234 systems for residential occupancies of design sprinklers (hydraulic design up to and including four stories in area)as specified for wet pipe sprinkler Technical height per NFPA 13R systems,as is accustomed for density/ area sprinkler systems designed per Data • wet and dry pipe sprinkler systems NFPA 13. for the residential portions of any Consequently, the Series LFII Resi Approvals occupancy per NFPA 13 q y' UL Listed(for use with wet pipe and dry dential Sprinklers offer the features i e s stems The recessed version of the Series of non-water filled pipe in addition p p y ) LFII Residential Sprinklers is intended to not having to increase the number C-UL Listed(for use only with wet pipe for use in areas with finished ceilings. of design sprinklers (hydraulic systems) It employs a two-piece Style 20 design area) for systems designed to Certified to all requirements of Recessed Escutcheon. The Recessed NFPA 13, 13D,or 13R. NSF/ANSI 61 Escutcheon provides 1/4 inch (6,4 mm)of recessed adjustment or up NOTICE (Refer to the Design Criteria section for to 1/2 inch(12,7 mm)of total adjustment details on these approvals.) from the flush ceiling position. The The Series LFII Residential Pendent Maximum Working Pressure adjustment provided by the Recessed and Recessed Pendent Sprinklers 175 psi(12,1 bar) (TY2234) described herein must be installed and maintained in compliance Discharge Coefficient with this document and the applicable K=4.9 gpm/psi1/2(70,6 Ipm/bar1'2) IMPORTANT standards of the National Fire Protec- Temperature Rating Always refer to Technical Data tion Association (NFPA), in addition to 155°F(68°C)or 175°F(79°C) Sheet TFP700 for the "INSTALLER the standards of any authorities having Finishes WARNING" that provides cautions jurisdiction.Failure to do so may Impair with respect to handlingand instal- Natural Brass,Pure White,Signal White,or Pthe performance of these devices. Chrome Plated lation of sprinkler systems and com- ponents. Improper handling and The owner is responsible for main- Physical Characteristics installation can permanently damage taming their fire protection system Frame Brass a sprinkler system or its components and devices in proper operating con- Button Copper and cause the sprinkler to fail to dition. Contact the installing contrac- Sealing Assembly .Beryllium Nickel w/TEFLON tor or roduct manufacturer with an Bulb(3 mm) ; operate in a fire situation or cause itp y Compression Screw ron , �� to operate prematurely. questions. Deflector............. 13tonz Page 1 of 6 JANUARY 2016 104842/2 02 0 ASPEN BUILDING DEPARTMENT TFP400 Page 2 of 6 7/16" (11,1 mm) 1/2„ ESCUTCHEON Components: NOMINAL NPT PLATE SEATING 2 7/8" DIA. 1 Frame MAKE-IN SURFACE (73,0 mm) 2 - Button 3 - Sealing Assembly 1 a / 4 Bulb _ _ I I=1 i 5 - Compression 2_ NScrew r�.� 1 — 2-1/4" 'm�i# 6 - Deflector* l�=1j (57,2 mm) ��� mor 3 t L I 1 1 kli 4 ' ' 1-5/8" STYLE 20 (41,3 mm) WRENCH C AG to RECESSED *Temperature 5 FLATSESCUTCHEON rating is _ I■�_ indicated on 6*_ Deflector. CROSS SECTION PENDENT RECESSED PENDENT FIGURE 1 RAPID RESPONSE SERIES LFII RESIDENTIAL 4.9K PENDENT AND RECESSED PENDENT SPRINKLERS(TY2234) Operation Tables A and B as a function of tern- the obstruction criteria described within I+ perature rating and the maximum the Technical Data Sheet TFP490. Theglass bulb contains a fluid that allowable coverage areas. The sprinkler flow rate is the minimum Operational Sensitivity expands when exposed to heat.When required discharge from each of the Sprinklers are to be installed with a the rated temperature is reached, the total number of "design sprinklers" as deflector-to-ceiling distance of 1-1/4 to fluid expands sufficiently to shatter the specified in NFPA 13D or NFPA 13R. 4 inches. glass bulb, allowing the sprinkler to The number of "design sprinklers" Sprinkler Spacing activate and flow water. specified in NFPA 13D and 13R for wet The minimum spacing between sprin- Desi/�n pipe systems is to be applied when klers is 8 feet (2,4 m). The maximum 7 designing dry pipe systems. spacing between sprinklers cannot Design exceed the length of the coverage area Criteria Hydraulic3) (Table A or B) being hydraulically cal- (NFPAThe TYCO RAPID RESPONSE Series For systems designed to NFPA 13,the 12f culated (e.g.,ft maximum area,12 feet for a LFII Residential 4.9K Pendent and number of design sprinklers is to be f2 ft.x ft2 ft.coverage ra r 20. feet Recessed Pendent Sprinklers are UL the four most hydraulically demanding for a 20 ft.x 20 ft.coverage area). and C-UL Listed for installation in sprinklers.The minimum required dis- accordance with this section. charge from each of the four sprinklers Residential Sprinkler is to be the greater of the following: Design Guide • The flow rates given in Table A or When conditions exist that are outside B as a function of temperature the scope of the provided criteria,refer rating and the maximum allowable to the Residential Sprinkler Design coverage area. Guide TFP490 for the manufactur- • A minimum discharge of 0.1 gpm/ft2 er's recommendations that may be over the "design area" comprised acceptable to the local authority having of the four most hydraulically jurisdiction. demanding sprinklers for actual System Types coverage areas protected by the Per the UL Listing, wet pipe and dry four sprinklers. pipe systems may be utilized. Per the The number of design sprinklers speci- C-UL Listing, only wet pipe systems fled in NFPA 13 for wet pipe systems is may be utilized. to be applied when designing dry pipe Refer to Technical Data Sheet TFP485 systems. for the use of residential sprinklers in DryPipe System Water Delivery residential dry pipe systems. When using the Series LFII Residential Ceiling Types Sprinklers (TY2234) in dry pipe sprin- Smooth flat horizontal, or beamed, or kler systems, the time for water deliv- sloped, in accordance with the 2013 ery must not exceed 15 seconds for the Edition of NFPA 13D, 13R, or 13, as most remote operating sprinkler. applicable. Obstruction to Hydraulic Design Water Distribution (NFPA 13D and 13R) Sprinklers are to be located in accor- For systems designed to NFPA 13D dance with the obstruction rules of or NFPA 13R, the minimum required NFPA 13D, 13R, and 13 as applicable sprinkler flow rates are given in for residential sprinklers as well as with 10/22/2020 ASPEN BUILDING DEPARTMENT TFP400 Page 3 of 6 WET PIPE SYSTEM Minimum Flow and Residual Pressure(2)(3) Maximum Ordinary Temperature Rating Intermediate Temperature Rating Coverage 155°F(68°C) 175°F(79°C) Minimum Area l Ft.x Ft. Flow Pressure Flow Pressure Deflector to Installation Spacing Ceiling Type Ft. (m x m) gpmpsi gpm psi (m) (I/min) (bar) (I/min) (bar) 12 x 12 13 7.0 13 7.0 Smooth (3,7 x 3,7) (49,2) (0,48) (49,2) (0,48) Ceilings 1-1/4 14 x 14 13 7.0 13 7.0(4,3 x 4,3) (49,2) (0,48) (49,2) (0,48) 4 inches Recessed Beamed using Style 20 16 x 16 13 7.0 13 7.0 Ceilings per Escutcheon or 8 (4,9 x 4,9) (49,2) (0,48) (49,2) (0,48) NFPA 13D non-recessed (2,4) 18 x 18 17 12.0 17 12.0 or 13R Per NFPA 13D, (5,5 x 5,5) (64,3) (0,83) (64,3) (0,83) 1-1/4 to 1-3/4 13R,or 13 inches below 20 x 20 20 16.7 20 16.7 bottom of (6,1 x 6,1) (75,7) (1,15) (75,7) (1,15) beam. Notes: 1. For coverage area dimensions less than or between those indicated,use the minimum required flow for the next highest coverage area for which hydraulic design criteria are stated. 2. Requirement is based on minimum flow in gpm(Ipm)from each sprinkler.The associated residual pressures are calculated using the nominal K-factor.Refer to Hydraulic Design under the Design Criteria section. 3. For NFPA 13 residential applications,the greater of 0.1 gpm/ft.2 over the design area or the flow in accordance with the criteria in this table must be used. TABLE A WET PIPE SYSTEM SERIES LFII RESIDENTIAL 4.9K PENDENT AND RECESSED PENDENT SPRINKLERS(TY2234) NFPA 13D, 13R,AND 13 HYDRAULIC DESIGN CRITERIA DRY PIPE SYSTEM Maximum Minimum Flow and Residual Pressure(2)(3) Coverage Ordinary Temperature Rating Intermediate Temperature Rating Areal 155°F(68"C) 175°F(79°C) Minimum Ft.x Ft. - Deflector to Installation Spacing (m x m) Flow Pressure Flow Pressure Ceiling Type Ft. gpm psi gpm psi (m) (I/min) (bar) (I/min) (bar) 12 x 12 13 7.0 13 7.0 Smooth (3,7 x 3,7) (49,2) (0,48) (49,2) (0,48) Ceilings 14 x 14 14 8.2 14 82 Z 4 inchee (4,3 x 4,3) (53,0) (0,57) (53,0) (0,57) ncs Recessed using Sle 16 x 16 15 9.4 15 9.4 Beamed Escutcheon20 or 8 (4,9 x 4,9) (56,8) (0,65) (56,8) (0,65) Ceilings non-recessed (2,4) per NFPA 13D per NFPA 13D, 18x18 18 13.5 18 13.5 or 13R 13R,or 13 (5,5 x 5,5) (68,1) (0,93) (68,1) (0,93) 1-1/4 to 1-3/4 inches below 20 x 20 21 18.4 21 18.4 bottom of (6,1 x 6,1) (79,5) (1,27) (79,5) (1,27) beam. Notes: 1. For coverage area dimensions less than or between those indicated,use the minimum required flow for the next highest coverage area for which hydraulic design criteria are stated. 2 Requirement is based on minimum flow in gpm(Ipm)from each sprinkler.The associated residual pressures are calculated using the nominal K-factor.Refer to Hydraulic Design under the Design Criteria section. 3. For NFPA 13 residential applications,the greater of 0.1 gpm/1t.2 over the design area or the flow in accordance with the criteria in this table must be used. TABLE B DRY PIPE SYSTEM SERIES LFII RESIDENTIAL 4.9K PENDENT AND RECESSED PENDENT SPRINKLERS(TY2234) NFPA 13D, 13R,AND 13 HYDRAULIC DESIGN CRITERIA RECEIVED 10/22/2020 ASPEN BUILDING DEPARTMENT TFP400 Page 4 of 6 2-7/8" DIA. - _ 7/16±1/8" (73,0 mm) 1/2"(12,7 mm) (11,1±3,2 mm) 2-1/4" DIA. 1/4"(6,4 mm) WRENCH RECESS FACE OF (57,2 mm) sl (END"A"USED SPRINKLER MOUNTING FOR TY2234) FITTING PLATE FIGURE 3 •� W-TYPE 6 SPRINKLER WRENCH IJlJ ■ir MOUNTING WRENCHRECESS SURFACE 1/8" (3,2 mm) 1-3/8"(34,9 mm) ' CLOSURE TY2234 1-1/8"(28,6 mm) FIGURE 2 STYLE 20 RECESSED ESCUTCHEON FOR USE WITH THE RAPID RESPONSE SERIES LFII RESIDENTIAL PENDENT SPRINKLER PUSH WRENCH Installation Recessed Pendent Sprinklers INTO ENSURE The Series LFII Residential Recessed ENGAGEMENT TYCO RAPID RESPONSE Series Pendent Sprinklers must be installed WITH SPRINKLER LFII Residential 4.9K Pendent and in accordance with the following WRENCHING AREA Recessed Pendent Sprinklers must instructions: FIGURE 4 be installed in accordance with this Step A. Install recessed pendent sprin- W-TYPE 7 RECESSED section. klers in the pendent position with the SPRINKLER WRENCH General Instructions deflector parallel to the ceiling. Do not install any bulb type sprinkler Step B. After installing the Style 20 if the bulb is cracked or there is a loss Mounting Plate over the sprinkler of liquid from the bulb.With the sprin- threads and with pipe thread sealant kler held horizontally,a small air bubble applied to the pipe threads, hand- should be present.The diameter of the tighten the sprinkler into the sprinkler air bubble is approximately 1/16 inch fitting. (1,6 mm). Step C. Tighten the sprinkler into the A leak-tight 1/2 inch NPT sprinkler joint sprinkler fitting using only the W-Type 7 should be obtained by applying a min- Recessed Sprinkler Wrench (Figure 4). imum-to-maximum torque of 7 to 14 With reference to Figure 1, apply the ft.-lbs. (9,5 to 19,0 Nm). Higher levels W-Type 7 Recessed Sprinkler Wrench of torque can distort the sprinkler Inlet to the sprinkler wrench flats. with consequent leakage or impairment of the sprinkler. Step D. After the ceiling has been installed or the finish coat has been Do not attempt to compensate for applied, slide on the Style 20 Closure insufficient adjustment in an Escutch- over the Series LFII Residential Sprin- eon Plate by under-or over-tightening kler and push the Closure over the the sprinkler. Re-adjust the position of Mounting Plate until its flange comes in the sprinkler fitting to suit. contact with the ceiling. Pendent Sprinklers The Series LFII Residential Pendent Sprinklers must be installed in accor- dance with the following instructions: Step 1.Install pendent sprinklers in the pendent position with the deflector par- allel to the ceiling. Step 2. With pipe thread sealant applied to the pipe threads, hand- tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench(Figure 3).With ref- erenceRECEIVED to Figure 1,apply the W-Type 6 Sprinkler Wrench to the wrench flats. 10/22/2020 ASPEN BUILDING DEPARTMENT TFP400 Page 5 of 6 Care and Limited Ordering Maintenance Warranty Procedure TYCO RAPID RESPONSE Series For warranty terms and conditions,visit Contact your local distributor for avail- LFII Residential 4.9K Pendent and www.tyco-fire.com. ability.When placing an order, indicate Recessed Pendent Sprinklers must be the full product name and part number maintained and serviced in accordance (P/N). with this section: Sprinkler Assemblies Before closing a fire protection system Specify: Series LFII 4.9K Residential main control valve for maintenance Pendent Sprinkler (TY2234), (specify work on the fire protection system that temperature rating),with(specify)finish, it controls,permission to shut down the P/N(specify): affected fire protection system must be 155°F(68°C) obtained from the proper authorities Natural Brass 51-201-1-155 and notify all personnel who may be Pure White(RAL 9010)* 51-201-3-155 affected by this action. signal White(RAL 9003) 51-201-4-155 Absence of the outer piece of an Chrome Plated 51-201-9-155 175°F(79°C) escutcheon, which is used to cover Natural Brass 51-201-1-175 a clearance hole, can delay sprinkler Pure White(RAL 9010)* 51-201-3-175 operation in a fire situation. Signal White(RAL 9003) 51-201-4-175 Chrome Plated 51-201-9-175 The owner must assure that the sprin- *Eastern Hemisphere sales only klers are not used for hanging any objects and that the sprinklers are only Recessed Escutcheon cleaned by means of gently dusting Specify: Style 20 Recessed Escutch- with a feather duster; otherwise, non- eon with(specify*)finish, P/N(specify*) operation in the event of a fire or inad- *Refer to Technical Data Sheet TFP770. vertent operation may result. Sprinkler Wrenches Sprinklers which are found to be Specify: W-Type 6 Sprinkler Wrench, leaking or exhibiting visible signs of P/N 56-000-6-387 corrosion must be replaced. Specify: W-Type 7 Sprinkler Wrench, Automatic sprinklers must never be P/N 56-850-4-001 painted, plated, coated, or other- wise altered after leaving the factory. Modified sprinklers must be replaced. Sprinklers that have been exposed to corrosive products of combustion, but have not operated,should be replaced if they cannot be completely cleaned by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid damage to the sprinklers before, during, and after installation. Sprin- klers damaged by dropping, striking, wrench twist/slippage,or the like,must be replaced. Also, replace any sprin- kler that has a cracked bulb or that has lost liquid from its bulb (Ref. Installa- tion section). The owner is responsible for the inspection,testing,and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Associa- tion (e.g., NFPA 25), in addition to the standards of any authorities having jurisdiction.Contact the installing con- tractor or product manufacturer with any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local ®�� ��+ i rt requirements and/or national codes. I� ,►. LL...� 10/22/2020 ASPEN BUILDING DEPARTMENT TFP400 Page 6 of 6 GLOBAL HEADQUARTERS 11400 Pennbrook Parkway,Lansdale,PA 19446 I Telephone+1-215-362-0700 Copyright©2016 Tyco Fire Products,LP. All rights reserved. tgCO 1 U/11/2 0 2 0 TEFLON is trademark of the DuPont Corporation. Fi,e Prrrtection Products ASPEN BUILDING DEPARTMENT Tube • Fittings • Valves COPPER FITTINGS FOR PLUMBING AND MECHANICAL APPLICATIONS Job Name Contractor Job Location Wholesaler Engineer Streamline® Rep Product Description: Streamline®Wrot Copper Pressure and DWV fittings for use in plumbing or mechanical applications.Available sizes ranging from "to 8"in diameter.Product is designed to join ASTM B88 and ASTM B280 Seamless CopperTube. Material: Streamline°Wrot Copper fittings shall be made from material in compliance with ASTM B75 and of UNS C 12200 grade of copper. Key Specifications: Streamline°Wrot Copper,solder joint,pressure fittings shall conform to the NSF/ANSI 61 Annex G requirements.Wrot copper pressure fittings shall be manufactured to meet ASME B 16.22 and MSS SP 104.Wrot DWV copper fittings shall be made to meet ASME B 16.29.All threaded fittings conform to ASME B I.20.I. Installation: Installations shall comply with the latest applicable building codes for the local jurisdiction.For detailed installation instructions, consult the Copper Developement Association at copper.org, References: NSF/ANSI 6 I Annex G Safe Drinking Water Act(third party certification) ASTM B75 Seamless CopperTube CI2200 99.9%pure copper ASME B 16.22 Wrot Copper and Copper Alloy Solder Joint Pressure Fittings MSS SP 104 Wrot Copper Solder and Joint Pressure Fittings ASME B 16.29 Drain,Waste and Vent(DWV) Fittings ASME B I.20.I Threaded Fittings Other Applicable Standards: ASTM B88 Seamless Copper Water and Gas Tube (Types K,L,M) ASTM B280 Seamless CopperTube for Air Conditioning and Refrigeration Copper(tube or fitting)UNS C122000 has been evaluated by NSF International to NSF/ANSI 61 for use in drinking water supplies of pH 6.5 and above. Drinking water supplies that are less than pH 6.5 may require corrosion control to limit leaching of copper into the drinking water. A BRAND OF MUELLER INDUSTRIES PA • • • Distributed by Mueller Streamline Co,•8285 Tournament Drive,Memphis,TN 38125•800-348-8464•www,muellerindustries,com page 1 of 8 :1 1 ` / • Tube • Fittings • Valves COPPER FITTINGS - PLUMBING SOLDER JOINT PRESSURE S DWV ADAPTER ADAPTER(CONT.) BUSHING(CONT.) FEMALE � REDUCING W 01759 x 1-1/4 5 50 0 94 WC-402 C z F En W 01113 1/4 x 1/2 50 500 0 08 W 01767 2-1/2 x 2 • 50 0 92 Pan Sae Box Cm Hn W 01114 x 3/8 50 750 0 06 BUSHING W 01207 1/8 100 1500 0104 W 01116 x 1/8 50 2000 0.02 S W 01215 1/4 50 750 0 04 W 01123 3/8 x 3/4 25 250 0 17 FLUSH H FTG X F • W 01225 3/8 50 750 0.07 W 01124 x1/2 50 500 0 09 ' WB01231 1/2 50 500 0,10 W 01126 x 1/4 50 750 0 05 (BRASS) WB01246 3/4 25 250 0.14 W 01129 1/2 x 1 15 150 0 30 'W Sat 1:1• C+^ xx WB01263 1 10 100 0 25 WB01130 x 3/4 25 250 0 17 A 07813 1/2 x 1/4 50 1200 0 02 W 01271 1-1/4 10 100 0,45 W 01132 x 3/8 50 500 0 07 A 07812 x 1/8 100 1600 0 04 W 01279 1-1/2 10 100 0.53 W 01133 x 1/4 25 600 0 06 A 07814 3/4 x 3/8 50 450 0 08 W 01287 2 - 50 0.57 W 01138 5/8 x 3/4 25 250 0 14 A 07815 1 x 1/2 50 300 0 17 W 01296 2-1/2 - 25 1 22 W 01139 x 1/2 25 250 0 12 A 07816 1-1/4 x 3/4 10 160 0 25 W 01297 3 - 15 1,83 W 01145 3/4 x 1 10 100 0 29 A 07817 1-1/2 x 1 10 90 0 34 REDUCING W 01147 x 1/2 25 250 0 12 A 07819 2 x 1-1/2 10 90 0 48 W 01204 1/8 x 1/2 100 300 0,10 W 01161 1 x 1-1/2 10 100 0 48 CAP W 01205 x3/8 100 700 0,05 W 01162 x 1-1/4 10 100 0 39 -r W 01206 x 1/4 100 900 0,04 W 01164 x 3/4 10 100 0 17 WC-415 C W 01214 1/4 x 3/8 50 750 0,06 W 01165 x 1/2 10 100 0 18 W 01216 x 1/8 100 1500 0,03 W 01170 1-1/4 x 1-1/2 10 100 0 48 J W 01223 3/8 x 3/4 50 300 0,16 W 01172 x 1 10 100 0.24 Pan Size Box Gin WI W 01224 x1/2 50 500 0,10 W 01173 x3/4 10 100 0.21 W 07002 1/8 50 2000 - W 01226 x 1/4 50 750 0.06 W 01178 1-1/2 x 2 - 50 0.78 W 07004 1/4 50 2000 0-01 WB01230 1/2 x 3/4 25 250 0,16 W 01180 x 1-1/4 10 100 0 37 W 07006 3/8 50 1000 0 01 W 01232 x 3/8 50 500 0,07 W 01181 x 1 10 100 (138 WB07007 1/2 50 1000 0 02 W 01233 x 1/4 50 500 0.06 W 01188 2 x 1-1/2 - 50 0.64 W 07008 5/8 50 2000 0 03 W 01238 5/8 x 3/4 50 500 0,15 W 01189 x 1-1/4 - 50 0,57 WB07009 3/4 25 1000 0 04 W 01239 x 1/2 50 500 0,09 W 01197 2-1/2 x 2 - 20 0.98 WB07011 1 10 500 0 08 W 01245 3/4 x 1 25 250 0,27 W 01198 x 1-1/2 - 22 0 98 W 07012 1-1/4 25 250 0 11 W 01247 x 1/2 25 250 0,11 W 07013 1-1/2 25 250 0 18 ADAPTER W 07014 2 - 100 0 30 W 01261 1 x 1-1/4 10 100 0,28 W 07015 2-1/2 50 0 48 W 01264 x 3/4 25 250 0,22 FITTING FTG x M ; i' W 07016 3 - 50 0 73 W 01265 x 1/2 20 200 0 25 WC-404 W 07017 3-1/2 - 25 1 15 W 01270 1-4/4 x 1-1/2 10 100 0.50 Pzn S„n so. :In Wi W 0701E 4 20 1 50 W 01272 x 1 10 1 D0 0 74 W 01278 1-1/2 x 2 - 50 0 39 W 01425 3/8 50 750 0.03 W 01431 1/2 50 500 0 09 COUPLING W 01280 x 1-1/2 5 50 0,74 W 01446 3/4 50 500 0 15 W 01288 2 x 1-1/2 5 50 0,74 W 01463 1 25 250 0.23 NO STOP C x C ADAPTER W 01471 1-1/4 10 100 0.41 WC 400N5 FITTING .. W 01479 1-1/2 10 100 0.49 P,n sae Bc. ain WI WC-405 FTG x F I -.F-1• W 01487 2 - 50 0 76 W 01900 1/8 100 4000 - `-�� W 01496 2-1/2 20 1 95 W 01901 1/4 50 2000 0.01 Wax &n Bo. CM an REDUCING W 01902 3/8 50 1700 0.01 W 01525 3/8 50 750 0.05 W 01432 1/2 x 3/8 50 750 0 06 W 01903 1/2 100 1000 0.03 W 01541 /4 50 450 0 11 3 W 01546 3/1 25 250 0. W 01447 3/4 x 1/2 50 500 0 13 W 01904 5/8 25 375 0.04 W01464 W 01905 3/4 50 500 0.06 W 01563 1 10 100 0,24 4 1 x 3/4 25 250 0 19 W 01906 1 25 250 0.11 W01571 1-1/4 10 100 040 n'�ItS'.�inhte'�'' W01907 1-1/4 25 250 0.15 W 01587 1-1/2 10 100 0.46 WA-515 FTG I W 01908 1-1/2 10 100 0.25 W 01587 2 50 0,65 W 01909 2 - 75 0.40 W 01596 2-1/2 - 25 1.20 Part 9:a Bo. Cm Wi W 01910 2-1/2 50 0.66 W 08000 1/2 x 8 - 100 0 22 REDUCING W 01911 3 - 25 1.03 W 01514 1/4 x 3/8 50 750 0 06 W 06001 x 12 - 50 0 42 W 01913 4 - 15 2.15 W 01524 3/8 x 1/2 50 350 0 10 W 06002 3/4 x 12 72 0 41 W 01526 x 1/4 50 750 0 06 BUSHING COUPLING W 01532 1/2 x 3/8 50 750 0 07 ROLLED STOP W 01547 3/4 x 1/2 50 500 0 11 FLUSH FIG WC-400 C X C W 01564 1 x 3/4 25 250 0 18 WC-106 pan 4x Be. CIn WI ADAPTER Pan Szre Sow Cm Wr W 01003 I/8 100 4000 - MALE W 01700 1/4 x 1/8 100 4000 0 01 W 01009 1/4 50 2000 0.01 WC-401 C z M . - 'I a W 01712 3/8 x 1/4 100 3400 0 01 W 01017 3/8 50 1700 0.01 W 01714 x1/8 100 2400 0 02 WB01022 1/2 50 1000 0.03 Pr., so Boa Cm rn W 01715 1/2 x 3/8 100 1500 0.02 W 01028 5/8 50 500 0.05 W 01107 1/8 50 2400 0.02 W 01717 x 1/4 100 1500 0,04 WB01034 3/4 25 500 0.06 W 01115 1/4 50 1200 0,03 W 01720 5/8 x 1/2 50 750 0 03 WB01047 1 10 250 0.11 W 01125 3/8 50 500 0.06 W 01721 x 3/8 50 750 0.06 W 01055 1-1/4 25 250 0.15 WB01131 1/2 50 500 0.06 W 01722 x1/4 50 750 0 08 W 01063 1-1/2 10 100 0.21 WB01146 3/4 25 250 0,13 W 01725 3/4 x 5/8 50 500 0 04 W 01072 2 - 75 0.40 WB01163 1 10 100 0.24 W 01726 x1/2 50 500 0,07 W 01082 2-1/2 - 50 0.08 W 01171 1-1/4 10 100 0.41 W 01727 x 3/8 50 500 0.11 W 01092 3 - 25 1.03 W 01179 1-1/2 10 100 0,51 W 01737 1 x 3/4 50 500 0,12 W 10100 3-1/2 - 20 1.18 W 01187 2 5 50 0.57 W 01738 x5/8 50 500 0.18 W 10107 4 - 15 2.11 W 01196 2-1/2 - 20 1.26 W 01739 x1/2 25 250 0,22 W 01199 3 - 20 1.70 W 01743 1-1/4 x 1 10 200 0,16 W 01150 4 - 16 3.71 W 01745 x 3/4 10 200 0.30 REDUCING W 01750 1-1/2 x 1-1/4 10 100 0,22 W 01105 1/8 x 3/8 50 750 0.06 W 01751 x 1 10 100 0.41 W 01106 x 1/4 50 1200 0 03 W 01758 2 x 1-1/2 10 100 0.68 A BRAND OF MUELLER IIYD{ISTRIES'�Er) a a a Distributed by Mueller Streamline Co.•8285 Tournament Drive,Memphis,TN 38125•800-348-8464•www.muellerindustries.com page 2 of 8 i1 1 ' 1 , ' Tube • Fittings • Valves COUPLING 45'ELBOW(CONT.) 90'ELBOW(CONT.) STAKED STOP W 03063 2-1/2 5 25 1 00 W 02734 3/4 25 250 0 13 WC 4005 C x C W 03067 3 20 1.53 W 02747 1 10 100 0 27 vy } an W 03070 3-1/2 10 2 81 W 02055 1-1/4 10 100 042 W 10141 118 100 3400 - W 03073 4 - 5 3 14 W 02063 1-1/2 5 50 0 60 W 1014 1/4 50 3400 0.- W 03074 5 - 1 6 56 W 02072 2 5 25 1 23 W 10143 13/4 50 2000 0.01 W 03075 6 - 1 10 64 W 02082 2-1/2 5 25 2 05 W 10145 1/2 100 1000 0.03 45'ELBOW W 02092 3 2 3 13 5 W 10157 5/8 25 500 0.04 W 02093 3-1/2 1 5 5.53 W 10146 3/4 50 500 0.06 STREET W 02095 4 1 7 98 W 10147 1 25 250 0.11 WE-505 FIG x C REDUCING W 10148 1-1/4 25 250 0.15 W 02711 1/4 x1/8 50 3000 0 01 W 10149 1-1/2 10 100 0.22 .art >ie 9n, Cm WI W 02723 1/2 x 3/8 50 1000 0 04 W 10150 2 - 75 0.41 W 03312 1/4 100 3400 0 01 W 02725 x1/4 50 1000 0 03 W 10151 2-1/2 - 50 0.66 W 03321 3/8 100 1500 0 03 W 02735 3/4 x 5/8 25 250 0 12 W 10152 3 - 25 1.02 WB03326 1/2 50 500 0,03 W 02736 x 1/2 50 500 0 09 W 10153 3-1/2 - 20 1.03 W 03330 5/8 50 500 0.06 W 02749 1x 3/4 10 100 017 W 10154 4 15 2.15 WB03334 3/4 25 250 0,09 W 02756 1-1/4x1 10 100 0 31 W 10155 5 - 8 3.34 W 03344 1 25 250 0,15 W 02058 x 3/4 10 100 0 37 W 10156 6 - 3 4.61 W 03350 1-1/4 10 100 0,24 W 02060 x1/2 10 100 0 37 W 10130 8 - 14.13 W 03355 1-1/2 10 100 0,33 W 02064 1-1/2 x 1-1/4 5 50 0 44 W 03359 2 5 50 0,61 W 02065 x 1 5 50 0 52 COUPLING W 03363 2-1/2 2 20 1,05 W 02067 x 3/4 5 50 051 REDUCING W 03368 3 2 10 1,52 W 02073 2 x 1-1/2 2 20 0.98 WC•400R C x C . W03373 4 - 5 3,11 W02074 x1-1/4 2 20 094 W 02075 x 1 2 20 0 97 Pan 3. 3a. tin WI •15 ELBOW W 01011 1/4 x 1/8 50 2000 0.01 90'ELBOW W 01019am 1/ 50 .170000 001 W 01021 x 1/8 50 1200 0 02 WE-507 FIG x FIG STREET SHORT W 01023 1/2 x 3/8 100 1000 003 RADIUS FIG x C an W 01025 x /4 100 1000 0.03 WE-503 W �7 &ee 3c. c:n WI 01027 x 1/2 100 1000 0 05 Ciro WI a W 03621 3/8 50 1700 0 02 pen 6.. o. W 01029 5/8 x 1/2 100 600 0.05 W 01030 x3/8 100 600 0-04 W 03626 1/2 50 750 0 04 W 02305 1/8 50 2000 0 01 W 01031 x1/4 100 600 0.04 W 03634 3/4 25 250 010 W 02312 1/4 50 1700 0 02 W 01035 3/4 x 5/8 100 1000 0-06 W 03644 1 10 100 0 18 W 02321 3/8 50 750 0 03 W801036 x 1/2 25 500 008 WB01652 1/2 50 500 0,04 W 01037 x 3/8 50 500 0.06 90 ELBOW W 02330 5/8 25 250 0,09 W 01038 x 1/4 50 500 0.06 a ‘• WB01654 3/4 25 250 0,10 W 01049 1 x 3/4 25 250 0 13 SHORT RADIUS ✓ � W 0105'0 x 5/6 25 250 0 11 W E-500 C x C r W 02334 3/4 25 250 0.11 W 01051 x 1/2 25 250 0.11 WB02344 1 10 100 0,22 W 01052 x 3/8 25 250 0 11 ' W 02384 1-1/4 25 125 0.29 W 01056 1-1/4 x 1 10 1,00 0 20 ' $a, a Cm WI W 02385 1-1/2 10 100 0.44 W 01058 x 3/4 10 100 0 17 W 02003 1/8 50 2000 0.01 W 02386 2 10 50 0 77 W 01060 x 1/2 10 100 0 17 W 02009 1/4 5D 1700 0.02 W 02387 2-1/2 5 25 1 23 W 01064 1-1/2 x 1-1/4 10 100 0 23 W 01617 3/8 50 750 0.03 W 02388 3 2 20 1 94 W 01065 x 1 10 100 0.23 W801622 1/2 50 500 0.04 W 02389 3-1/2 1 10 2 78 W 01067 x3/4 10 100 0.24 W 02028 5/8 50 500 0,08 W 02390 4 2 10 4.03 W 01069 x 1/2 10 100 0.22 WB01634 3/4 25 250 0.09 W 01073 2 x 1-1/2 - 100 0 43 W01074 x1.1/4 - 100 043 W801647 1 10 100 0.18 90'ELBOW W 01075 x - 100 0,45 W 02085 1-1/4 10 100 0.30 w alnn z 3!4 100 OAO W 02085 1-t/2 10 100 0.47. STREET LONG RADIUSFIG x C an W 01079 x 1/2 - 75 0 41 W 02086 2 10 50 0 76 WE-503L W 01083 2-1/2 x 2 - 50 0.65 W 02087 2-1/2 5 25 1,19 W 01084 x 1-1/2 - 50 0-75 W 02088 3 5 25 1 88 Hen sre au cm wvryI W 01085 x 1-1/4 • 50 0.70 W 02089 3-1/2 2 10 2.77 W 02809 1/4 50 1700 0.02 W 01086 x 1 - 50 0.71 W 02090 4 2 10 4 00 W 02817 3/8 50 500 0 04 W 01093 3 x 2-12 25 1.06 1 W 01095 2 - 25 1 W 02096 5 - 1 8 59 W 02822 1/2 50 500 0 06 W 01095 x 1-11/2 - 25 1_ 01 W 02097 8 - 1 13.73 W 02828 5/8 25 250 0 09 W 10101 3-1/2 x 3 - 25 1.22 W 02099 8 - 1 27 00 W 02834 3/4 25 250 0 13 W 10108 4 x 3-1/2 - 20 1.87 REDUCING W 02847 1 10 100 0 26 W 10109 x 3 - 20 0,76 W 02011 1/4 x 1/8 50 750 0.02 W 02350 1-1/4 10 100 0 42 W 10110 x 2.1/2 - 15 1.88 W 02019 3/8 x 1/4 50 750 0 03 W 02355 1-1/2 5 50 0 60 W 10111 x 2 - 20 197 W 02023 1/2 x 3/8 50 500 0.05 W 02359 2 5 25 1 23 W 1013 5 x 4 - 1 3.31W 02025 x 1/4 50 500 0.05 W 02363 2-1/2 5 25 2 08 W 10124 8 x 3 - 1 4 W 02029 5/8 x 1/2 50 500 0 06 W 02368 3 2 10 3 12 W 10 24 x 3 t 4.82'BB W 02030 x 3/8 50 500 0 07 W 02393 3-1/2 1 5 5 52 COUPLING W 02035 3/4 x 5/8 50 500 0.11 W 02395 4 - 1 8 07 CROSS OVER W 02036 x 1/2 50 500 0 11 WC-412 C x CC/ W 02037 x 3/8 50 500 0.11 90'ELBOW ?.xn a ale Co WI W 02049 1 x 3/4 25 250 0.17 SHORT RADIUS A 02535 1//2 5 100 0 12 W 02050 x 5/8 25 250 016 FIG x FIG G:=3 A02583 3/4 5 50 026 W02051 x1/2 25 250 0.18 WE-506 45'ELBOW W 02052 x 3/8 25 150 0-20 W 02056 1-1/4 x 1 20 200 0.32 W 02612 1/4 50 2800 0 02 W 02077 1-1/2 x 1-1/4 5 100 0.33 W 02621 3/8 50 750 0 03 WE-504 C X C W 02078 2 x 1-1/2 5 50 0,60 W 02626 1/2 50 500 0 05 90 ELBOW W 02634 3/4 25 250 0.11 Pen sue so. C1n WI / W 02644 1 10 100 0 22 3U W 0U5 1/8 bU 2000 001 L I e W 02684 1-1/4 10 100 031 W 03012 1/4 50 2800 0 01 LONG RADIUS C X C W 02685 1-1/2 5 50 0 43 W 03021 3/8 50 850 0.03 WE-500L W 02686 2 1 10 0.79 WB03026 1/2 50 500 004 W 02687 2-1/2 1 10 125 W 03030 5/8 50 500 0 06 W 02715 1/8 50 2000 0" W 02688 3 1 10 2.08 WB03034 3/4 25 250 0.09 W 1 W 02689 3-1/2 1 10 2 63 WB03044 1 10 200 0,16 W 0271 02716 1 13/4 50/8 50 100 70 0 0 0 0 02 W 02690 4 1 5 3 88 W0305 1-1/4 10 100 036 WW02722 1/2 50 500 006 W03055 1-1/2 10 100 0.36 W 03059 2 10 50 0,60 W 02728 5/8 50 500 0.09 �E D w A BRAND OF MUELLER INDUSTRIES a I I Distributed by Mueller Streamline Co.•8285 Tournament Drive,Memphis,TN 38125•800-348-8464•www.muellerindustnes.com page 3 of 8 i I I ` I -' - r . • 0 Tube • Fittings • Valves 90'ELBOW(CONT.) RETURN BEND TEE(CONT.) REDUCING LONG RADIUS WE-512 C x C W 04029 x 5/6 25 250 0.10 WE-506L FTG x FTG W 04007 x 3/8 50 500 0.08 Pan o'ca Bo. Cm WI W 04008 x 1/4 50 500 0.06 Pan s:e Du. ce, WI W 06025 1/4 x 4-1/2 25 150 0 10 W 04014 x 1/8 50 500 0.08 W 02650 1 1/4 5 50 0 44 W 06020 x 1-1/2 25 850 0 02 W 04009 x 3/8 x 1/2 50 500 0.09 W 02655 1-1/2 5 50 0 63 W 06048 3/8 x 6 - 100 0 21 W 04010 x 3/8 50 500 0.08 W 02659 2 1 10 1 23 W 06045 x 4 - 200 0 14 W 04011 x 1/4 50 500 0.08 FITTING REDUCER W 06041 x 3 25 250 0 11 W 04012 x 1/4 x 1/2 50 500 0.09 W 06036 x 2 50 300 0 06 W 40367 x 3/8 50 500 0.08 - W 06035 x 1-29/32 50 300 0 08 W 04013 *1/4 50 500 0.09 WC-403 FTG x C J W 06032 x 1-1/2 50 500 0 06 W 04046 5/8 x 5/8 x 3/4 25 250 0.15 W 06069 1/2 x 6 5 30 0 30 W 04018 x 1/2 25 250 0 10 Pan S,re Bo. om WI W 06062 x 3-3/8 10 100 0 18 W 04019 x 3/8 25 250 0.10 W 01306 1/4 x 1/8 50 2000 0O1 W 06060 x 3 25 150 0 16 W 04020 x 1/4 25 250 0.10 W 01312 3/8 x 1/4 50 2000 0 02 W 06058 x 2-1/2 25 250 0 14 W 04021 x 1/2.5/8 25 225 0.13 W 01314 x 1/8 50 2800 0 01 W 06056 x 2-1/4 25 250 0 13 W 04022 x 1/2 25 250 0.11 W 01315 1/2.3/8 50 750 0 03 W 06053 x 1-7/8 25 250 0 11 W 04023 x 3/8 25 225 0.11 W 01317 x 1/4 50 1700 0 02 W 06051 x 1-9/16 25 250 0 10 W 04025 x 3/8 5/8 25 250 0.15 W 01320 5/0 x 1/2 100 1000 0 04 W 06084 5/8 x 4 - 120 0 25 W 04026 x 1/2 25 225 0.14 W 01321 x 3/8 100 900 0 04 W 06081 x 3-3/8 10 90 0 24 W 04027 x 3/8 25 250 0.11 W 01322 ..1/4 100 900 0 04 W 06077 x 2-1/2 10 100 0.17 W 04065 3/4 x 3/4 x 1 10 100 0.22 W 01325 3/4.5/8 50 500 0 06 W 06074 x 2-1/8 10 100 0 16 W 04032 x 5/8 25 250 0.17 WB01326 x 1/2 25 500 006 W 06073 x 2 10 100 015 WB04033 x 1/2 25 250 0.12 W 01327 .3/8 50 500 0 06 W 06099 3/4 x 12 - 15 0.88 W 04034 x 3/8 25 250 0.11 W 01337 1 ,3/4 25 250 0 11 W 06095 x 3-3/8 10 100 0 29 W 04035 x 1/4 25 250 0.11 W 01338 x 5/8 25 250 0 10 W 06092 x 2-1/2 10 100 0 23 W 04036 x 5/8 x 3/4 25 250 0.19 W 01339 x 1/2 25 250 0 10 W 60111 1 x 3-1/4 5 50 0 49 W 04037 x 5/8 25 250 0.17 W 01340 x 3/8 20 200 0.10 W 60110 x 3 5 50 0.47 WB04041 x 1/2 x 3/4 25 250 0.16 W 01343 1-1/4 x 1 10 100 0 17 W 60121 1-1/4 x 3-3/4 5 50 0.65 W 04042 x 5/8 25 150 0.17 W 01345 x 3/4 10 100 0 17 W 60131 1-1/2 x 4-1/2 5 25 1.00 WB04043 x 1/2 25 250 0.13 W 01347 x 1/2 10 100 0 16 W 60140 2 x 5-1/2 5 25 1 92 W 04044 x 3/8 25 250 0.12 W 01350 1-1/2 x 1-1/4 10 100 0 23 P-TRAP W 04045 x 1/4 25 225 0.15 W 01351 x 1 10 100 0.24 W 40230 x 3/8 x 3/4 25 250 0.19 W 01353 x 3/4 10 100 0 23 q n W 40231 x 1/2 25 250 0.17 W 01355 x 1/2 10 100 0 22 SUCTION LINE C x C I Ivl f W 40232 x 3/8 25 250 0.12 W 01358 2 x 1-1/2 100 0 44 WE-554P W 40101 1 x 1 x 1-1/2 5 50 0.47 W 01359 x 1-1/4 - 100 0.43 W 04082 x 1-1/4 5 50 0.31 W 01360 x 1 - 100 0.45 Pert 3.t. Ras CM W WB04049 x 3/4 10 100 0.24 W 01362 x 3/4 - 100 0 43 W 80999 1/2 II) 50 0.38 W 04050 x 5/8 10 100 0.27 W 01364 x 1/2 - 100 0 42 W 61008 5/6 10 50 0 51 WB04051 x 1/2 10 100 0.21 W 01367 2-1/2 x 2 - 50 0.62 W 61000 3/4 5 25 0 63 W 04052 x 3/8 10 100 0.19 W 61001 1 3 15 0.87 W 01368 x1-1/2 - 50 0_57 W 04055 1x3/4x1 10 100 0.30 W 01369 x 1-1/4 - 50 0 62 W 61002 1-1/4 4 20 1,16 y�04056 x 3/4 10 100 0.25 W 01370 x 1 - 50 0 63 W 61003 1-1/2 4 4 2,28 W 04057 x 5/8 10 90 0.43 W 01376 3 x 2-1/2 - 25 1 00 W 61009 2 3 3.87 W 04058 x 1/2 10 100 0.23 W01377 x2 - 25 089 1 k E W04059 x3/8 10 100 0.21 W 01378 x 1-1/2 - 50 0 92 W 40233 x 5/8 x 1 10 100 0.33 W 01379 x 1-1/4 - 50 1 01 W 40234 x 3/4 10 90 0.30 W 01381 3-1/2 x 3 - 20 1 28 WT-600 C x C x C W 40235 x 5/8 10 100 0.31 W 01382 x 2-1/2 - 20 1.37 W 40236 x 1/2 10 90 0.35 W 01383 x 2 20 1 47 Pan 440 EL. cm W. W 04061 x 1/2 x 1 10 100 0.30 W 01386 4 x 3-1/2 - 20 1 74 W 40306 1/8 100 2400 001 W 04062 x 3/4 10 100 0.28 W 01387 x 3 - 15 1.77 W 04000 1/4 50 1700 0.02 W 04063 x 1/2 10 100 0.21 W 01388 x 2-1/2 - 15 1 83 W 04001 3/8 50 500 0 04 W 40122 1-1/4x1-1/4 x2 2 20 0.89 W 01389 x 2 - 15 1 86 WB04006 1/2 50 500 0 07 W 40100 x 1-1/2 5 50 0.49 W 01390 5 x 4 - 1 3 24 W 04017 5/8 25 250 0 12 W 04069 x 1 5 5D 0.41 W 01391 x 3 - 1 2 76 WB04031 3/4 25 200 0 16 W 04070 x 3/4 5 50 0.35 W 01393 x 2 - 1 2 66 WB04048 1 10 100 0 29 W 04071 x 1/2 5 50 0.32 W 01394 6 x 5 - 1 4 80 W 04068 1-1/4 5 50 0 42 W 04072 x 3/8 5 50 0.29 W 01395 x 4 - 1 4 32 W 04084 1-1/2 5 50 0 60 W 04073 x 1 x 1-1/4 5 50 0.48 W 01 96 .3 1 4.4 W 40102 2 5 25 1.14 W 04074 x 1 5 50 0.46 W 40123 2-1/2 2 20 1 72 W 04075 x 3/4 5 50 0.38 W 40152 3 2 10 2 77 W 04076 x 1/2 5 50 0.36 HI-EAR V W 40190 3-1/2 1 5 5.66 W 04078 x 3/4 x 1-1/4 5 50 0.45 W-124 C W 40200 4 1 5 5 99 W 04079 x 1 5 50 0.46 Pan Saa Bo. Cm WI W 40400 5 - 1 12 38 W 04080 x 3/4 5 50 0.37 A 03167 1/2 100 1000 0.03 W 40500 6 - 1 20 85 W 04081 x 1/2 5 50 0.34 A 03168 3/4 25 500 0 04 W 40525 8 - 1 36.81 W 04083 1/2 x 1-1/4 5 50 0.57 A 03171 1 25 250 0.04 REDUCING W 40121 1-1/2x1-1/2x2 2 20 1.21 W 40368 1/8 x 1/8 x 1/4 50 750 0 03 W 04085 x 1-1/4 5 50 0.57 PLUG W 04016 1/4 x 1/4 x 1/2 50 500 0.08 W 04086 x 1 5 50 0.52 FITTING W 04005 x 3/8 50 500 0 04 W 04087 x 3/4 5 50 0.47 WC-416 W 40324 x 1/6 50 1700 0.02 W 04068 x 1/2 5 50 0.42 (SIZES 1/B THRU 11/2 FTG W 40330 x 1/8 x 1/4 50 500 0.02 W 04089 x 3/8 5 50 0.41 BRASS ROD) W 40332 x 1/8 50 1700 0.02 W 04090 x1-1/4x1-1/2 5 50 0.68 Pan sue eo. Cm Nr W 04015 3/8 x 3/8 x 1/2 50 500 0.09 W 04091 x 1-1/4 5 50 0.69 A 01402 1/8 50 500 001 W 04002 x 1/4 50 500 0.04 W 04092 x 1 5 50 0.57 A 01422 1/4 1UU 4000 U U1 W 4U35U x 1/8 5U 50U U 04 W U4U93 x 3/4 5 SO 0.57 A 01392 3/8 50 2000 0 02 W 04003 x 1/4 x 3/8 50 500 0,05 W 04094 x 1/2 5 50 0.45 A 01504 1/2 50 1200 0 03 W 04004 x 1/4 50 500 0.04 W 04095 x 1 x 1-1/2 5 50 0.68 A 01529 3/4 50 600 0 07 W 40358 x 1/8 50 750 0.04 W 04096 x 1-1/4 5 50 0.65 A 01556 1 25 375 0 12 W 40363 x 1/8 x 3/8 50 750 0 05 W 04097 x 1 5 50 0.61 A 01590 1-1/4 15 180 0 20 W 40364 x 1/4 50 750 0 04 W 04098 x 3/4 5 50 0.56 A 01628 1-1/2 10 120 0 28 W 40366 x 1/8 50 450 0 05 W 40237 x 1/2 5 30 0.45 W 04067 1/2 x 1/2 x 1 1D 100 0 35 W 04099 x 3/4 x 1-1/2 5 50 0.67 W 04047 x 3/4 25 250 011 W 40239 x 1-1/4 5 50 0.75 W40240 x1 5 50 A BRAND OF MUELLER INDETCFJWEE) • • • Distributed by Mueller Streamline Co.•8285 Tournament Dnve.Memphis.TN 38125•800-348-8464•www muellenndustries corn page 4 of 8 ;1 I ` 8 1 , Tube • Fittings • Valves TEE CONT.) TEE(CONT.) ADAPTER REDUCING REDUCING W 40238 x 3/4 x 3/4 5 50 0.55 W 40194 x 1-1/4 10 4.55 TRAP W 40243 x 1/2 5 50 0 47 W 40193 x 1 10 3.05 DW-757 F x SJ W 40244 x 1/2 x 1-1/2 5 50 0 66 W 40192 x 3/4 10 2.89 . W 40153 2 x 2 x 3 1 10 2.55 W 40191 x 1/2 10 2.89 Pan sae W. Cm xn W 40144 x 2-1/2 I 10 1 46 W 40208 x 3 x 4 5 8.66 A 11409 1-1/4x1.1/4 0D 10 100 0 34 W 40103 x 1-1/2 5 50 0 99 W 40206 x 3 5 5.12 A 11410 1-1/2x1-1/2 0D 10 100 0 40 W 40104 x 1-1/4 5 50 0.85 W 40205 x 2-1/2 5 5.61 REDUCING W 40105 x 1 5 50 0.88 W 40204 x 2 5 4.76 A 11411 1-1/2x1-1/4 OD 10 100 0 40 W 40106 x 3/4 5 50 0,83 W 40212 x 2-1/2 x 4 5 7.79 ADAPTER W 40107 x 1/2 5 50 0.67 W 40216 x 2 x 4 5 8.95 W 40108 x 3/8 2 20 0,68 W 40215 x 1-1/2 x 4 5 8.51 TRAP W 40109 x 1-1/2 x 2 2 20 1.31 W 40214 x 1-1/4 x 4 5 8.57 M x SJ 1-. - 2 W 40110 x 1-1/2 2 20 1.15 W 40213 x 1 x 4 5 9.33 DW-756 W40111 x1-1/4 2 20 0.86 W40401 5 x 5 x 4 - 6.95 �� W 40112 x 1 2 20 1.06 W 40402 x 3 - 6.25 v,n Sew two. CI" WI W 40113 x 3/4 2 20 0.75 W 40404 x 2 - 5.05 A 11405 1-1/4x1-114 0D 10 100 0 42 W 40114 x 1/2 5 50 0.77 W 40520 6 x 4 x 4 - 12.52 A 11406 1-1/2x1-112 OD 10 100 0 52 W 40115 x 1-1/4 x 2 2 20 1.30 W 40502 x 6 x 4 - 11.00 REDUCING W 40116 x 1-1/2 2 20 1,14 W 40503 x 3 - 11.00 A 11407 1-1/2x1-1/4 OD 10 100 0 53 W 40117 x 1-1/4 2 20 1,09 W 40504 x 2-1/2 - 11.10 ADAPTER W 40118 x 1 2 20 0,95 W 40505 x 2 - 9.54 W 40119 x 3/4 5 50 0,76 W 40526 8 x 8 x 4 - 22.26 SOIL PIPE C X SPIGOT= W 40120 x 1/2 5- 20 0,78 TEE OW-733 JJ W 40245 x 1 x 2 5 25 64 W 40247 x 1 5 50 06 'n 3a, +r Co, WI W 40248 x 3/4 x 2 5 25 71 FITTING C x FTG x C W 07122 2 5 100 0 43 W 40249 x 1/2 x2 5 25 .66 WT-600F W 07133 3 5 40 1 12 W 40124 2-1/2 2-1/2 x 2 2 20 59 REDUCING W 40125 x 1-1/2 2 20 49 W 04106 1/2 50 300 0.10 W 07112 x 2 5 50 0 61 W 40126 x 1-1/4 2 20 87 W 04131 3/4 25 150 0 19 ADAPTER W 40127 x1 2 20 83 W 40128 x 3/4 1 10 83 UNION W 40129 x 1/2 1 10 2.05 FEMALE IlE2 W 40130 x 2 x 2-1/2 4 20 2.30 Km DW-753 C x F W 40131 x 2 2 20 1.84 WC-407 C x C W 40132 x 1-1/2 4 20 2.09 r,n sae Boa Cm WI W 40133 x 1-1/4 4 20 2,12 r,n sae ea. Cu, wI W 07221 1-1/2 10 100 0.25 W 40134 x1 4 20 2,10 W 08001 1/4 25 250 0 12 W 07222 2 10 100 0 41 W 40135 x 3/4 4 20 2,06 W 08002 3/8 25 250 0 11 ADAPTER W 40136 x 1/2 4 20 2,20 W 08004 /4 25 250 0 7 3 W 40137 2-1/2x1-1/2x2-1/2 4 20 2,32 W 08004 3/4 25 150 0 7 W 40138 x 2 4 20 1,84 W 08005 1 10 100 0 52 DW-754 FTG x F W 40139 x 1,-1/2 4 20 2,11 W 40140 x 1-1/4 4 20 2.17 COPPER TUBE STRAP ran Sae 90< Cm un W 40141 x1 4 20 1,83 - W 07240 1-1/4 10 100 0.19 W 40142 x 3/4 4 20 2.36 2-HOLE W 40143 x 1/2 4 20 2,36 WS-1100 ADAPTER W 40220 x 1-1/4 x 2-1/2 4 20 2.35 ran Sias no. CIn WI W 40250 x 2 4 20 1.82 •A 01203 1/8 100 4.000 0.01 W 40251 x 1-1/2 4 20 2.47 A 01278 1/4 100 5,600 0.01 DW-732 C x M al W 40252 x 1-1/4 4 20 1.96 A 01366 3/8 100 3,400 0.01 W 40253 x 1 4 20 2.47 A 02529 1/2 100 1,500 0.01 ran s Box CanwI W 40254 x 3/4 4 20 2.18 A 01467 5/8 100 2,000 0,01 2 W 40255 x 1/2 4 20 247 A07012 1-1/4 5 250 0.35 W 40221 x 1 x 2-1/2 4 20 2.39 A 02574 3/4 50 750 0 01 A 07054 1-1/2 10 100 0 44 W 40256 x 2 4 20 1.97 A 02614 1 50 750 0 02 A 07094 2 10 100 052 W 40257 x 1-1/2 4 20 2.15 A 02675 1-1/4 50 500 0 05 REDUCING W 40258 x 1-1/4 4 20 2.04 A 02 1-1/2 50 500 0 OS W 07235 1-1/4 x 1-1/2 10 100 0.37 W 40259 x 1 4 20 2 27 A 02708 08 2 50 500 0 O6 W 40222 x 3/4 x 2-1/2 4 20 2 41 PERFORATED COPPER STRAP BUSHING FE W 40151 3 x 3 x 2-1/2 2 10 2.45 WS-1101 )- - • EXTENDED W 40150 x 2 2 20 2 30 r,n xi. oe• Ce an FTG x C W 40149 x 1-1/2 2 10 2 18 A 01.'1 1 25 F1.11011 1 10 1.63 DW-742 W 40148 x 1-1/4 2 10 2.38 W 40147 x 1 2 20 1-96 ran ae 0.. em WI W 40146 x 3/4 2 20 1 49 SOLDER JOINT DWV FITTINGS W 07350 1-1/2 x 1-1/4 25 250 0.11 W 40145 x 1/2 2 20 1.38 W 07358 2 x 1-1/2 - 100 0 22 W40159 3x2-1/2x3 2 10 296 W07359 x1-1/4 - 100 018 W 40158 x 2-1/2 2 10 4 52 ADAPTER W 07377 3 x 2 - 50 0 47 W 40157 x 2 2 10 2-68 W 07378 x 1-1/2 - 50 0 44 W 40156 x1-1/2 2 10 2.63 TRAP W 07379 x 1-1/4 - 50 0.50 W 40155 x 1-1/4 2 10 2.62 DW-724F FTG x SJ a , W 07387 4 x 3 - 25 0.89 W 40154 x 1 2 20 2,02 W 07389 x 2 - 25 1 03 W40167 x2x3 2 10 3.07 Pan sae so. -m WI CLOSET FLANGE W 40165 x 2-1/2 2 10 4 64 A 11564 1.1/2x1-1/2 OD 10 100 0 28 W 40164 x 2 2 10 2.75 REDUCING DW-734 C x CLOSET 1 if W 40163 X 1-1/2 2 10 2.57 A 11566 1-1/2x1-1/4 OD 10 100 0 26 W 40162 x 1-1/4 2 10 2.61 ran al_-a 0... cm WI W 40161 x 1 2 20 2 04 ADAPTER W 07834 3 x 4 5 50 0 83 W 40174 x1-1/2 x 3 2 10 2.97 W 07844 4 x 4 5 40 0.67 W 40181 %1 1/4 x 3 2 10 3 14 TRAP C x SJ i if 2 COUPLING W 40178 x 1 x 3 2 10 3-02 DW-724 W 40179 x 3/4 x 3 2 10 303 - W 40198 4 x 4 x 3 1 5 4 94 r,n sae Bo. CI, wi DW-741 C x C W 40197 x 2-1/2 1 5 5.16 A 11355 1-1/4x1-1/4 00 25 250 0 22 W 40196 x 2 1 10 4 52 A 11356 1-1/2x-1/2 OD 10 200 0,33 'an sae See Cm Wi W40195 x1-1/2 1 10 447 REDUCING W07055 1.1/4 25 150 009 A 11383 1-1/2x1-1/4 00 10 200 0 40 W 07063 1-1/2 25 250 9FC11EfuI A BRAND OF MUELLER _ • a a Distributed by Mueller Streamline Co.•8285 Tournament Drive.Memphis,TN 38125•800-348-8464•www muellerindustnes.com page 5 of 8 it I 1 I •i Tube • Fittings • Valves COUPLING(CONT.) 60-ELBOW W 07092 100 0,17 W 07092 1 50 10,47 ,03 W 70107 I 25 DW-701 C x C `(/-I/\ REDUCING W 07073 2 x 1-1/2 - 100 0,17 Part Size Box Gin WI W 07074 x1-1/4 - 100 0.18 W 07064 1-1/2 25 250 0 35 W 07094 3 x 2 - 50 0,52 W 07066 3 2 20 0 95 W 07095 x 1-1/2 - 50 0,52 22-1/2 ELBOW W 07096 x 1-1/4 - 50 0.70 W70106 4x2 - 25 10 33 P W 70106 x 2 - 25 1 30 DW-703 C x C REPAIR COUPLING "an Sve Bo. Cln WI DW-741NS C x C 7 W 07060 1-1/2 - 100 027 Pan Ha* an. an WI TEE W 07907 1-1/4 25 225 0 07 W 07908 1-1/2 25 250 0 11 DW-707 C x C x C 1- W 07909 2 - 75 0 19 W 07911 3 - 50 0 34 Pvl Srsa Do. Gin wr 45'ELBOW W 07500 1-1/4 20 100 0.37 4?. W 0751 22 1-1/2 5 1 5 0 85 DW-204 C x C W 0751 2 5 25 0 85 W 07533 3 10 2 10 REDUCING Pan an In W' W 07510 1 1/2x1 10 100 0 51 W 07420 1.1/4 25 250 0.14 112x1-1/4 W 07421 1-1/2 25 125 030 W 07512 x1-1/4x1-1/4 10 100 0.52 W 07422 2 - 50 0.33 W 07521 2 x 2 x 1-1/2 5 50 0 75 W 07423 3 25 0.84 W 07520 x 1-1/4 5 30 0.68 45'ELBOW W 07524 x1.1/2x1-1/2 5 50 0.87 W 07532 3 x 3 x 2 5 25 169 W 07531 x 1-1/2 5 25 1.45 (STREET) FTG x C W 07530 x 1-1/4 5 25 0.81 DW-205 TE51 CAP a ran Ste Bm C n WIW 07430 1-1/4 25 250 017 DW-798T C W 07431 1-1/2 25 125 0 20 W 07432 2 - 50 0 32 .art 5tra env Gin WI W 07433 3 - 25 0 81 W 07634 1/2 500 5.000 - 90'ELBOW W 07635 3/4 200 4,000 - W 07636 1 100 2,000 0,01 DW-200 C x C G W 076371-1/4 100 2,000 0,01 W 07638 1 1-1/2 100 1,000 0,01 W 07639 2 50 1,000 0 02 W 07400 1-1/4 25 125 0 25 W 07640 3 25 250 0 04 W 07401 1-1/2 20 100 0 24 VENT INCREASER W 07403 2 - 50 0 71 W 07404 3 15 1 66 I mu DW-752 C xTUBE rmill 90 ELBOW LONG TURN Pan Son So. Gin WI D-7WLT CxC 0° W 70112 3x4x18 - 6 4.37 W70111 3x4x24 5 590 Pon 9s. No. Ctn WI A 07209 1-1/2 5 100 0 41 A 07202 7 5 40 0 62 90'ELBOW EXTRA LONG TURN C x C an DW-700XLT Part Srn Boa Cm WI W 07451 1-1/2 10 50 0.55 W 07452 2 5 25 1 11 W 07453 3 2 10 2 28 W 07454 4 - 5 5 10 90 ELBOW f�I�1I DW-203 FTG x C L" 1 P.,I W W W. c WI W 07410 l 1 4 25 125 0 26 W07411 1-1/2 20 100 0.38 W 07412 2 - 50 0.70 W 07413 3 - 15 1 70 A BRAND OF MUELLER aECSVE D • • • Distributed by Mueller Streamline Co.•8285 Tournament Drive,Memphis,TN 38125•800-348-8464•www.muellerindustries corn page 6 of 8 •1 I ' I r Tube • Fittings • Valves COPPER FITTING DATA TEMPERATURE - PRESSURE RATINGS OF SOLDER JOINTS SERVICE STANDARD TUBE SIZE,TYPES K,LAND M ALLOYS USED TEMPERATURE WATER AND NON-CORROSIVE LIQUIDS&GASES FOR JOINTS °F I/4 to I I-I/4 to 2 2-I/2 to 4 1 5 to 8 100 _ 200 175 150 135 50/50 Tin Lead Solder 150 150 125 100 _ _90 _ Not to be used in potable water systems 200 _ 100 _ 90 75 70 250 85 75 50 45 100 1090 _ 850 705 660 150 625 485 405 375 95/5 Tin-Antimony Solder - - - 200 505 395 325 305 250 270 210 175 _ 165 100 710 555 460 430 150 475 370 305 285 Alloy E Solder 200 375 290 240 225 250 320 250 205 195 100 1035 805 670 625 Alloy HB Solder 150 710 555 460 430 200 440 345 285 265 250 430 335 275 260 Brazing Alloys (melting at or above 1000°F) Pressure-temperature ratings is that of the tubing being used Note:Ratings ore those given in ASME B 16.22 "Wrought Copper and Copper Alloy Solder Joint Pressure Fittings."(a)Solder alloys are covered byASTM Standard Specification 832. The Safe Drinking Water Act Amendment of 1986 prohibits the use of any solder having a lead content in excess of 02%for potable water systems. PRESSURE LOSS IN FITTINGS EXPRESSED AS EQUIVALENT LENGTH OF TUBE, FEET Normal or Wrot Copper Fittings Standard 90 Degree 45 Degree Tee Tee 180 Degree in Inches Ell Ell Straight Run Side Branch Coupling Bend 3/8 0.5 0.5 0.5 I 0.5 1/2 0.5 0.5 0,5 I I - 5/8 0.5 0,5 0.5 2 - 3/4 I 0.5 0.5 2 - 2 I 1 I 0.5 3 - 2 I-1/4 2 I 0.5 4 0.5 3 —I-1/2 2 2 I 5 0.5 4 2 1 2 2 'I 7 0.5 8 2-1/2 2 1 3 2 9 0.5 16 3 3 4 - I 20 A BRAND OF MUELLER INICEIVED II i i Distributed by Mueller Streamline Co.•8285 Tournament Drive,Memphis,TN 38125•800-348-8464•www.muellenndustries.com page 7 of 8 •II II 'i IP -• 1111111M]theilMilillun 5eanilth 0 Tube • Fittings • Valves COPPER TUBE AND SOLDER TYPE FITTINGS 1. Cut tube square with the cutter or fine hack I. Cut tube to length & remove saw(32 tooth blade is recommended). dir burr with file or scraper. Remove Burr. 2. Clean outside end of copper tube thoroughly •� with sand cloth or sandpaper equal depth of fitting.Leave no dark spots. 2. Clean outside of tube with 3• Clean inside of fitting carefully to tube stop with sandpaper or sand cloth. wire brush.Note:Sand cloth or sandpaper may also be used. i 4. Using a brush,apply light uniform coat of soldering flux to the outside of the tube 3. Clean inside of fitting with wire and inside of the fitting, brush,sand cloth or sandpaper. 5. Slip tube into fitting to tube stop. Turn tube back and forth once or twice to distribute flux evenly. 6.Apply heat uniformly around the fitting with 4.Apply flux thoroughly to torch. When solder melts upon contact with inside of fitting. heated fitting,the proper soldering temperature — . has been reached. Remove flame and feed solder slightly off center at the bottom of the joint.Proceed across the bottom of the fitting and up to the top center position. Return to the starting point,and then proceed up the 5.Apply flux thoroughly to incomplete side to the top,again,overlapping outside of tube-assemble the solder metal. Wipe off surplus solder with tube and fitting. a piece of cloth. CAUTION: No not overheat the joint or direct the flame into the face of the fitting cup. Overheating could burn the flux, 6.Apply heat with torch,When whichwill destroy itseffectiveness andthe solder melts upon contact with solder will not enter the joint properly. FIL.M.1 heated fitting,the proper temp for soldering has been reached. ' Remove flame&feed solder to the joint at one or two points until a ring of solder appears at the end of the fitting. RFCF FED A BRAND OF MUELLER INDUSTRIES M • a a Distnbuted by Mueller Streamline Co.•8285 Tournament Drive,Memphis,TN 38125•800-348-8464•www muellenndustries.com page 8 of 8 NI I 'lb ■ - ' • Tube • Fittings • Valves COPPER TUBE FOR PLUMBING AND MECHANICAL APPLICATIONS Job Name Contractor Job Location Wholesaler Engineer Streamline° Rep Product Description: Streamline®CopperTube for use in plumbing and mechanical applications.Available sizes (Type K,L,M,& DWV) ranging from %"to 8"in diameter.All tube shall be manufactured in the United States. Material: Streamline°CopperTube is manufactured from UNS C 12200 grade of copper. Key Specifications: Streamline®CopperTube (Type K,L,M) shall conform to the NSF/ANSI 61 Annex G requirements and is manufactured to meet ASTM B88.Copper drainage tube (DWV) is made to meet ASTM B306.Copper refrigeration coils,ACR/Nitrogenized straight lengths and line sets are made to meet the chemical, mechanical,cleanness and eddy current testing requirements of the applicable specifications of ASTM B280. Installation: Installations shall comply with the latest applicable building codes for the local jurisdiction.For detailed installation instructions, consult the Copper Developement Association at copperorg. References: ASTM B75 Seamless CopperTube C 12200 99.9%Pure Copper(can be used for potable water) NSF/ANSI 61 Annex G Safe Drinking Water Act(third party certification) ASTM B88 Seamless Copper Water and GasTube (Type K,L,M) ASTM B280 Seamless CopperTube for Air Conditioning and Refrigerants ASTM B306 Seamless Drainage Tube Code (DWV) Copper[tube or filling]UNS C122000 has been evaluated by NSF International to NSF/ANSI 61 for use in drinking water supplies of pH 6.5 and above. Drinking water supplies that are less than pH 6.5 may require corrosion control to limit leaching of copper into the drinking water. F( YED MADE IN USA A BRAND OF MUELLER INDUSTRIEFAY ` • • Distributed by Mueller Streamline Co.•8285 Tournament Drive,Memphis,TN 38125•800-348-8464•www.muellerindustries.com page 1 of 4 aI I I -' • Tube • Fittings • Valves COPPER TUBE DATA Streamline°Copper Tube sets the standard for quality,consistency and service in the plumbing industries. With a full line of copper tube products to support most all plumbing supply and DWV applications,Streamline°Copper Tube is available in all common types including Type K, Type L,Type M and DWV. Each piece of tube is incised marked and color coded for easy, long lasting identity. Manufactured in accordance with applicable standards, our ongoing commitment to quality continues to make Streamline°Copper Tube the preferred and specified brand of industry professionals. TYPE K RATED WORKING PRESSURE (PSIG) NOM.DIA. WT/FT FT/BNDL 1 150°F 200°F 1 300°F 400°F 1 1/4 0.145 500 913 860 842 537 3/8 0.269 500 960 904 885 565 _ 1/2 0.344 500 j 758 713 698 446 5/8 _ 0.418 200 626 589 577 368 _ 3/4 _ 0,641 200 1 724 682 668 426 • _ 0.839 _ 100 1 557 524 513 _ 327 I 1/4 1.04 100 452 425 1 416 266 11/2 1.36 100 420 396 387 247 • 2 2.06 - 370 348 341 217 2 1/2 2.93 - 338 319 312 _ 199 3 4.00 I - 328 308 302 193 _ 3 1/2 5.12 - 31.1 293 286 183 I 4 6.51 - 306 288 282 180 1 5 9.67 . _ - 1293 276 270 172 6 _ — 13.90 -- 295 277 271 -_ 173 8 25.90 - 314 295 289 . 184 TYPE L _ 1/4 0.126 500 775 729 714 456 3/8 0.198 500 662 623 610 389 • 1/2 0.285 500 613 577 565 361 5/8 0.362 r 200 537 505 495 316 3/4 0.455 200 495 466 456 291 i_ 0.655 100 420 395 387 247 1 i _ I 1/4 0.884 100 373 351 344 1 219 I 1 1/2 1.14 100 347 327 320 _ 204 • 2 1.75 - 309 r 291 1 285 - 182 I 2 1/2 2.48 - 285 269 263 168 i 3 3.33 - 270 254 248 159 3 1/2 4.29 - 1 258 243 238 152 I 4 5.38 1 - i 249 235 230 147 5 7.61 - _ 229 215 211 135 6 10.2 - 211 201 196 125 } 8 19.3 1 - I 230 216 i 212 135 Tables give computed allowable stress for annealed copper tube at indicated temperature. PFCF /ED A BRAND OF MUELLER INDUSTRIES I i I Distributed by Mueller Streamline Co.•8285 Tournament Drive,Memphis.TN 38125•800-348-8464•wvrw.muellenndustnes.com page 2 of 4 e• I 'r • - , ® Tube • Fittings • Valves COPPER TUBE DATA TYPE M RATED WORKING PRESSURE(PSIG) NOM.DIA. i _ WT/FT FT/BNDL 150°F 200°F 300°F 400°F i 3/8 0.145 - i 485 456 447 285 _ 1/2 _ 0.204 500 420 _ 395 387 247 3/4 0.328 200 346 326 319 204 0.465 100 286 270 264 169 1 1/4 _ 0.682 100 287 271 265 169 1 1/2 0,94 100 282 265 259 166 1,46 - 254 239 234 149 2.03 - 233 219 215 137 3 2,68 - 215 203 199 127 3 1/2 3.58 214 202 197 _ 126 4 4.66 213 _ 201_ 197 126 •5 6.66 - 198 186 182 116 6 8.92 _ • 186 _ _ 175 171 109 • 8 16.5 • 195 183 180' 115 TYPE DWV NOM.DIA WT/FT FT/BNDL 150°F 200°F 300°F • 400°F I 1/4 — 0.65 100 280 269 258 165 I 1/2 0.809 100 2.49 240 230 147 2 1.07 185 178 170 109 3 1,69 - r 135 130 125 _ 80 4 2.87 - 127 122 117 75 5 4.43 - 129 124 119 76 6 6.1 - 126 121 I16 74 8 10.6 - 124 119 114 73 Table give computed allowable stress for annealed copper tube at indicated temperature. TECHNICAL DATA Values of allowable internal working pressure for copper tube in service are based on the formula from ANSI B3 I,Standard Code for Pressure Piping: 2 S tm P= D max-0.8 tm P= Allowable Pressure ©150°F S= 5100 PSIG annealed S = Allowable stressD max-0.8 tm 200°F S= 4800PSIG annealed T= Wall thickness ©300°F S= 4700 PSIG annealed D Max= Outside Diameter @ 400°F S= 3000 PSIG annealed All ratings listed tar types K, L, M,DWV and refrigeration service tube in the preceding charts are calculated for tube in the annealed condition.These values should be used when soldering,brazing or welding is employed for joining components in a system.While the ratings for hard drawn tube are substantially higher,they should only be used for systems using properly designed flare or compression mechanical joints, since joining by any heating process might anneal (soften)the tube. In designing a system, careful consideration should also be given to joint ratings as well as those of the components. ^ ED ru?F A BRAND OF MUELLER INDUSTRIES a a a Distributed by Mueller Streamline Co.•8285 Tournament Drive,Memphis,TN 38125•800-348-8464•www.muellerindustnes.com page 3 of 4 III I ' I- -' ' ' Tube • Fittings • Valves COPPER TUBE AND SOLDER TYPE FITTINGS I. Cut tube square with the cutter or fine hack • I• Cut tube to length & remove saw(32 tooth blade is recommended). burr with file or scraper. Remove Burr. 2. Clean outside end of copper tube thoroughly i�r with sand cloth or sandpaper equal depth of fitting.Leave no dark spots. 2. Clean outside of tube with 3. Clean inside of fitting carefully to tube stop with sandpaper or sand cloth. wire brush.Note:Sand cloth or sandpaper may also be used. 4. Using a brush,apply light uniform coat of soldering flux to the outside of the tube and inside of the fitting. 3. Clean inside of fitting with wire brush,sand cloth or sandpaper. - 5. Slip tube into fitting to tube stop. Turn tube back and forth once or twice to distribute flux evenly. 6.Apply heat uniformly around the fitting with ' 4.Apply flux thoroughly to torch. When solder melts upon contact with � inside of fitting. heated fitting,the proper soldering temperature has been reached. Remove flame and feed solder slightly off center at the bottom of the joint.Proceed across the bottom of the fitting and up to the top center position. Return to the starting point,and then proceed up the 5.Apply flux thoroughly to incomplete side to the top,again,overlapping outside of tube-assemble the solder metal. Wipe off surplus solder with tube and fitting. 1":3**1 a piece of cloth. CAUTION: No not overheat the joint or direct the flame into the face of the fitting cup. Overheating could burn the 6.Apply heat with torch.When flux, which will destroy its effectiveness - solder melts upon contact with and the solder will not enter the joint � heated fitting,the proper temp properly. — - for soldering has been reached. Remove flame&feed solder to the joint at one or two points until a ring of solder appears at the end of the fitting. A BRAND OF MUELLER INDUSTRIES Distributed by Mueller Streamline Co.•8285 Tournament Dnve,Memphis.TN 38125•800-348-8464•www muellenndustries.com page 4 of 4 Pipe Hangers Fig. 200 - "Trimline" Adjustable Band Hanger (B-Line Fig.B317ONF) ®TOLCO Fig. 200F- "Trimline" Adjustable Band Hanger with Felt Lining (B-Line Fig.B317ONFF) C UL U5 Fig. 200C - "Trimline" Adjustable Band Hanger with Plastic Coated (B-Line Fig.B317ONFC) LISTED Fig. 200S - "Trimline" Adjustable Band Hanger with Non-Captured Nut Size Range: Fig. 200 - 1/2" (15mm1 thru 8" (200mm)pipe Material: Steel, Pre-Galvanized to G90 specifications Function: For fire sprinkler and other general piping purposes. Knurled swivel nut design permits hanger adjustment after installation. i 9 \ Features: 4 • (1/2" (15mm)thru 2" (5omm1) Flared edges ease installation for all pipe types and protect CPVC plastic pipe from abrasion. Captured design keeps adjusting nut from separating with hanger. Hanger is easily t A B installed around pipe. i For hanger with non-captured nut order Fig. 200S. • (21/2" 165mm)thru 8" (2o0mm)) Spring tension on nut holds it securely in 1 ` __ hanger before installation. Adjusting nut is easily removed. Approvals: Underwriters Laboratories listed (1/2" (15mm)thru 8" (200mml) Fig.zoo-1/z.zoo-3/+ in the USA(UL) and Canada (cUL)for steel and CPVC plastic pipe and 1 Fig.200-1 to 200-2 Fig.200-21/z to 200-8 Factory Mutual Engineering Approved (FM) (3/4" (20mm)thru 8" (200mm(l. Conforms to Federal Specifications WW-H-171 E &A-A-1 192A, Type 10 and Manufacturers Standardization Society ANSI/MSS SP-69 &SP-58, Type 10. Maximum Temperature: 650°F(343°C) Finish: Pre-Galvanized. Stainless Steel materials will be supplied with (2)hex nuts in place of a knurl nut. Order By: Figure number and pipe size Designed to meet or exceed requirements of FM DS 2-0. O (1:14111)11 t4 Afr nic Fig.200 a Fig.200C Fig.200F Pipe Size Rod Size A B Approx.Wt./100 Part No. in. (mm) in. (mm) in. (mm) lbs. (kg) 200-1/2 1/2' (15) 3/8"-16 31/8" (79.4) 25/8" (66.7) 11 (5.0) 200-3/4 3/4" (20) 3/8"-16 31/8" (79.4) 21/2" (63.5) 11 (5.01 200-1 1" (25) 3/8"-16 33/8" (85.7) 25/8" (66.7) 12 (5.5) 200-11/4 11/4" (32) 3/8"-16 33/4" (94.0) 27/e" (73.0) 13 (5.9) 200-11/2 11/2" (40) 3/8"-16 37/8" (98.4) 27/8" (73.0) 14 (6.4) 200-2 2" (50) 3/8"-16 41/2" (114.3) 3" (76.3) 15 (6.9) 200-21/2 21/2" (65) 3/8"-16 55/8" (142.9) 41/8" (104.7) 27 (12.3) 200-3 3" (75) 3/e"-16 57/8" (149.1) 4" (101.6) 29 (13.3) Fig.200S 200-31/2 31/2" (90) 3/8"-16 73/8" (187.3) 51/4" (133.3) 34 (15.6) 200-4 4" (100) 3/8"-16 73/8" (187.3) 5' (127.0) 35 (16.0) 200-5 5" (125) 1/2"-13 91/8" (231.8) 61/4" (158.7) 66 (30.2) 200-6 6" (150) 1/2%13 101/8" (257.2) 63/4" (171.4) 73 (33.4) 200-8 8" (200) 1/2%13 131/8" (333.4) 83/4" (222.2) 136 (62.3) RECEIVED All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. A ,ae 0 n 0 arre Fire Protection Solutions 21EIT.N G by ASPEN BUILDING DEPARTMENT Pipe Hangers Fig. 2- Adjustable Band Hanger (B-Line B3170) ®TOLCO Fig. 2F- Adjustable Band Hanger Felt Lined for Copper Tubing (B-Line B3170F) COis Size Range: UPS Fig. 2 - 21/2" 165mm1 thru 6" (150mm) pipe i Fig. 2F - 272" (65mm)thru 6" (150mm) pipe Material: Pre-Galvanized Steel J C B Function: Recommended for the suspension of non- • 0 insulated pipe or insulated pipe with B3151 shield. . , I Fig. 2NFPA accomodates the reduced rod schedule of 1 4 4 iii, the National Fire Pretection Association Pamphlet 13. 2 a. o Approvals: Factory Mutual Engineering Approved. Underwriters Laboratories Listed. Conforms to Federal Fig'2 Specification WW-H-171 E &A-A-1 192A Type 10 and 'LAI; ' I , Manufacturers Standardization Society ANSI/MSS SP-69 &SP-58,Type 10. Standard Finish: Pre-Galvanized Note: Available in Stainless Steel material. 1. Order By: Part number and finish. It (411) B C I -4 r I�Nil 1 f d ° Fig.2F L� 1 41 Fig.2 r- S Nominal Pipe Size Rod Size B C D Max.Rec.Load Approx Wt./100 3i Part No. in. (mm) A in. (mm) in. (mm) in. (mm) lbs. (kN) lbs. (kg) 11111 2-21/2 21/2' (65) llz'" 13* 53/4" (146.4) 41/4" (107.9) 15/8" (41.3) 600 (2.67) 41 (18.6) 2 3 3" (75) 1/2" 13* 6" (152.4) 41/8" (104.8) 11/4" 131.71 600 (2.67) 45 (20.4) 2-31/2 31/2" (90) 1/2"-13* 73/8" (187.3) 51/4" (133.3) 21/8" (54.0) 600 (2.67) 52 123.61 2-4 4" (100) 5/8"-11 * 73/8" (187.3) 5" (127.01 15/8" (41.3) 1000 (4.45) 59 (27.6) 2-5 5' (125) 5/8"-11** 9" (228.6) 61/8" 1155.6) 21/4" (57.1) 1250 (5.56) 97 (44.0) 2-6 6" (150) 3/4"-10** 93/8" (238.11 61/2" (165.1) VA" (47.6) 1250 (5.56) 139 (63.0) t Fig.2F Nominal Pipe Size Rod Size B C D Max.Rec.Load Approx Wt./100 Part No. in. (mm) A in. (mm) in. (mm) in. (mm) lbs. IkN) lbs. (kg) 2F-21/2 21/2" (65) 1/2"-13* 53/4" (146.0) 41/4" (107.9) 15/8" (41.3) 600 (2.67) 41 (18.6) 2F-3 3" (75) 1/2"-13* 6" (152.4) 41/8" (104.8) 11/4" (31.7) 600 (2.67) 45 (20.4) 2F-31/2 31/2" (90) 1/2"-13* 73/8" (187.3) 51/4" (133.3) 21/8" (54.0) 600 (2.67) 52 (23.6) 2F-4 4" (100) 5/e"-11* 73/8" (187.3) 5" (127.01 15/8" (41.3) 1000 (4.45) 59 (27.6) 2F-5 5" (125) 5/8"-11** 9" (228.6) 61/8" (155.6) 21/4" (57.1) 1250 (5.56) 97 (44.0) 2F-6 6" (150) 3/4"-10** 93/8" (238.11 61/2" (165.1) 17/8" (47.6) 1250 (5.56) 139 (63.01 * 3/s nut is used when requested. ** '/z nut is used when requested. RECEIVED ■ All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise ipe�i7dn n/n O n O 6-Line 22 Fire Protection SUUor/utioonss G w E:t•N ASPEN BUILDING DEPARTMENT Pipe Hangers Fig.200M - "Trimline" Adjustable Band Hanger for Metric Rod ®TOLCO Size Range: C0 US Fig. 200 - 1/2" (15mm)thru 8" (200mm) pipe USTED Material: Steel, Pre-Galvanized to G90 specifications Function: For fire sprinkler and other general piping purposes. Knurledia swivel nut design permits hanger adjustment after installation. il Features: • (1/2" 115mm)thru 2" (50mm)) Flared edges ease installation for all pipe types and protect CPVC plastic pipe from abrasion. Captured design keeps adjusting nut from separating with hanger. Hanger is easily 1 installed around pipe. `� • (21/2" 165mm)thru 8" (20omm)) Spring tension on nut holds it securely in hanger before installation. Adjusting nut is easily removed. / B Approvals: Underwriters Laboratories listed (1/2" (15mm)thru 8" (2oomml) Fig.200-1to200.2 in the USA(UL)and Canada (cUL)for steel and CPVC plastic pipe and A • Factory Mutual Engineering Approved (3/4" (20mm)thru 8" (2oomm)l. t Conforms to Federal Specifications WW-H-171 E &A-A-1192A,Type 10 - ors. and Manufacturers Standardization Society ANSI/MSS SP-69&SP-58, Type 10. 1 Fig.200-1/2.200-3/4 Maximum Temperature: 650°F (343'C) Fig.200-21/z to 200-B Finish: Pre-Galvanized. Stainless Steel materials will be supplied with (2) hex nuts r in place of a knurl nut. Order By: Figure number and pipe size Designed to meet or exceed requirements of FM DS 2-0. ` 41110 -- Pipe Size Rod Size A B Approx.Wt./100 Part No. in. Imm) in. (mm) in. (mm) lbs. (kg) 200MB-1/2 1/2' (15) M8 31/e" (79.4) 25/8" (66.7) 11 (5.0) 200M10-1/2 1/2" (15) M10 31/8" (79.4) 25/8" (66.7) 11 (5.0) 200M8-3/4 3/4" (20) M8 31/8" (79.4) 21/2" (63.5) 11 (5.0) 200M10-3/4 3/4" (20) M10 31/8" (79.4) 21/2" (63.5) 11 (5.0) 200M8-1 1" (25) M8 33/e" (85.7) 25/8" (66.7) 12 (5.5) 200M10-1 1" (25) M10 33/8" (85.7) 25/8" (66.7) 12 (5.5) 200M8-11/4 11/4" (32) M8 33/4" (94.0) 27/e" (73.0) 13 (5.9) 200M10-11/4 11/4" (32) M10 33/4" (94.0) 27/8" (73.0) 13 (5.9) 200M8-11/2 11/2" (40) M8 37/e" (98.4) 27/a" (73.0) 14 (6.4) 200M10-11/2 11/2" (40) M10 31/8" (98.4) 27/8" (73.0) 14 (6.4) 200M8-2 2" (50) M8 41/2" (114.3) 3" (76.3) 15 (6.9) 200M10-2 2" (50) M10 41/2" (114.3) 3" (76.3) 15 (6.9) 200M-21/2 21/2" (65) M10 55/e" (142.9) 41/8" (104.7) 27 (12.3) 200M-3 3" (75) M10 57/8" (149.1) 4" (101.5) 29 (13.3) 200M-31/2 31/2" (90) M10 73/8" (187.31 51/4" (133.3) 34 115.6) 200M-4 4" (100) M10 73/8" (187.3) 5" (127.0) 35 (16.0) 200M-5 5" (125) M12 91/8" (231.8) 61/4" (1513.7) 66 (30.2) 200M-6 6" (150) M12 101/8" (257.2) 63/4" (171.4) 73 (33.4) 200M-8 8" (200) M12 131/e" (333.4) 83/4" (222.2) 136 (62.3) RECEIVED All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. a i_■_ 02 G n 0 by Fire Protection Solutions 23 ??xxtASPEN BUILDING DEPARTMENT Spare Sprinkler Head Storage Cabinet ti FPPI Description Fire Protection Products, Inc. Spare Sprinkler Head Cabinets are designed to allow for spare sprinkler head storage as required by NFPA guidelines.The Spare Sprinkler Head Cabinets are available in six configurations.Three head, six head, six head ESFR, twelve head, twenty-four head, and thirty-six head. All six styles are manufactured with "knockouts" to accommodate the most common size sprinklers.The shelf is positioned to allow for the storage of a typical sprinkler head wrench. Each cabinet is finished in red enamel. Each spare head cabinet comes with a hinged door which remains closed to protect the spare sprinklers from the elements and features holes on the back panel to allow for attachment to most surfaces utilizing the appropriate fasteners. Not intended for exposed or harsh environments. Installation Specifications Select the correct Spare Sprinkler Head Cabinet in accordance with the Automatic Sprinkler Systems Handbook. As per the 1989 Edition the correct number of spare Material: Steel-22 Gauge sprinkler is as follows: Finish: 0-300 sprinklers, not less than 6; 300-1000, not less than 12; 1000 or more, not Red enamel less than 24. Stock of spare sprinklers shall include all types and ratings installed.* Styles: 3 Spare sprinklers,'/2 or 3/4 Once the correct Spare Sprinkler Head Cabinet has been selected, installation 6 Spare sprinklers,'h or 3/4 6 Spare,ESFR,'/2,3/4 or 1" is accomplished by inserting the correct fastener in each of the holes inside the 12 Spare sprinklers'/2 or Y4 cabinet, securing the cabinet securely to the wall. Insert the correct number and 24 Spare sprinklers type of sprinklers in accordance with the"handbook". 36 Spare sprinklers 'Final determination is subject to approval by the AHJ. 3198 LIONSHEAD AVE CARLSBAD,+1 TEL 760 599-1168 +1 800 344-1822 FAX+1 800 344-3775 ©2016 Fire Protection Products,Inc. RECEIVED tl II II • • I 1 ASP N BUILDING DEPARTMENT Spare Sprinkler Head Storage Cabinet �I : 1 F P P I' Dimensions Cabinet Type Length Depth Height Height (open) 12 head cabinet 141" 4" 5 '/a" 10'/,s (02-400-00) 6 head cabinet 141/4" 2 7/,s 5 ye 101/4" (02-401-00) 3 head cabinet 7 6/1 ' 2 Y" 5 14" 10 1" (02-402-00) ESFR cabinet, 6 head 14 Ya" 3 3/,' 6 1/2" 12 3/a" (02-403-00) 24 head cabinet 14 IA" 4" 8'/,s 17" (02-404-00) 36 head cabinet 12 5/,s 4" 11 3/4" 26"/,s' (02-405-00) (Length open) 3198 LIONSHEAD AVE CARLSBAD, CA 92010 TEL+1 760 599-1168 +1 800 344-1822 FAX+1 800 344-3775©2016 Fire Protection Products,Inc. RECEIVED L BUILDING DEPARTMENT Spare Sprinkler Head Storage Cabinet 1 F P P I "Height Open" "Length" "Height Closed" "Depth" Item Numbers 02-400-00 to 02-404-00 3198 LIONSHEAD AVE �i CARLSBAD, CA 92010 TEL+1 760 599-1168 �_. +1 800 344-1822 FAX+1 800 344-3775 P ©2016 Fire Protection Products,Inc. RECEIVE D 111111 • i 1 ASP N BUILDING DEPARTMENT Spare Sprinkler Head Storage Cabinet 41 1 FPPI- Depth" [ o o Q o o — ------, o o 0 0 "Height" O O O O O O "Length" -------------- I I "Length Open" Item Number 02-405-00 3198 LIONSHEAD AVE CARLSBAD, CA 92010 Wi TEL+1 760 599-1168 S +1 800 344-1822 FAX+1 800 344-3775©2016 Fire Protection Products,Inc. RECEIVED „ „ yy . . iyo ASPL_ BUILDING DEPARTMENT Open Snoot Assembly Hi' FNPT x FNST* Connection F P P Description • The single outlet open snoot is constructed of cast brass.The single swivel is ma`s complete with gasket and comes standard with pin lugs. Outlet is 21/2" NPT . female thread. Comes standard with 2'h" NST female swivel. Kit includes: open snoot, 2 1/2" brass plug with chain, and 21/2" FDC Brass Wall Plate. Installation Specifications Installation can be achieved with tools readily available in the field using common installation practices. Make sure male threads of pipe to which the Material: Cast Brass snoot is being attached are liberally coated with a pipe thread sealant such as PipeFit Thread Sealant with PTFE or PTFE Thread Sealant Tape.Tighten the Size: snoot until hand tight.Tighten one additional turn past hand tight to achieve a 2'/2 FNPT x F Swivel* water tight seal of the threads. DO NOT OVER TIGHTEN! Over Tightening may *Available Swivels: cause thread failure as well as cracking of the snoot body. NST 3.0686"x 71/2 TPI BCT 3.000"x 8 TPI CLV 3.078"x 8 TPI DET 3.125"x 7/2 TPI ONT 3.125"x 5 TPI PHX 3.062"x 6 TPI QST 3.031"x 7 TPI TEM 3.075"x 6 TPI Check thread dimensions for other 21/2"applications. _ 3198 LIONSHEAD AVE BAD, CA 92010 TE L+CARLS11 760 599-1168 +1 800 344-1822 FAX+1 800 344-3775 ©2012 Fire Protection Products,Inc. a AWARNING: _ Ca ductiveHann www.P85Warr ngs.ca.gov II II II ASP N BUILDING DEPARTMENT Identification Signs I,b` FPPF Description Manufactured from .020" white coated aluminum. All sign types are screen printed with a fade resistant red ink. Each sign is shipped with a clear protective plastic coating which can be re- moved at time of installation. Each sign type meets or exceeds NFPA13 requirements. All signs (except 7" round) are drilled in four corners to allow for easy installation. All signs(except emir 7" round) may be installed with sign chain or with any fastener that is suitable for the material �..� -- gpRfN that the sign is being attached. The 7" round bell signs are center drilled to allow for installation �'�', �R4- ' directly to the bell gong assembly. Type "A" 9" x 7" Control valve signs are drilled with the same J q4 ARM four hole pattern as Type "B" 6" x 2" signs to allow for attachment of Type "B" to Type "A". "�� AF A/,�S pep?. Installation Specifications Installation of aluminum signs is accomplished by several methods. The most common installation procedure is to use#16 Single Jack chain to hang the Material: .020"aluminum with sign on the area being identified. Since all of the above mentioned signs are removable plastic coating predrilled at all four corners, the last link of the chain can be opened and hooked through the top holes on the signs and hung on the appropriate valve or piping. Sizes: 6"x2" The signs may also be fastened to a flat surface with fasteners appropriate to 4"x 6" the base material. (The 9"x 7" Fire Alarm Bell sign must be drilled with a 3/8" hole 5"x 7" if it is to be attached directly to the bell gong.) 9"x 7" 12"x10" 8.5"x 11" 7" Round See current catalog for a full listing of all available signs. 3198 LIONSHEAD AVE CARLSBAD, CA 92010 TEL+1 760 599-1168 +1 800 344-1822 FAX+1 800 344-3775 RECEIVED ©2012 Fire Protection Products,Inc r 10/22/r�2020 It tt If 0 0 ES-007 For Non-Health Hazard Applications Job Name Contractor Job Location Approval Engineer Contractor's P.O. No. Approval Representative Series 007 Double Check Valve Assemblies • Sizes: 1/2" -2" - - mop, — Series 007 Double Check Valve Assemblies are designed to r protect drinking water supplies from dangerous cross-connec- tions in accordance with national plumbing codes and water authority requirements for non-potable service applications 1" 007M1QT such as irrigation,fireline, or industrial processing. Only those cross-connections identified by local inspection authorities as non-health hazard shall be allowed the use of an approved double check valve assembly. 116Misr Check with local authority having jurisdiction regarding vertical orientation,frequency of testing or other installation requirements. The valve shall meet the requirements of ASSE Std. 1015 and AWWA Std. C510. Approved by the Foundation for Cross- Connection Control and Hydraulic Research at the University of 1" 007M1QT-S Southern California. Test Cocks Features • Ease of maintenance — only one cover • Top entry I I 1 • Replaceable seats and seat discs • Modular construction • Compact design • Cast bronze body construction — 1/2"—2" • Top mounted ball valve test cocks • Low pressure drop First Check Second Check Module Assembly Module Assembly • No special tools required for servicing • Yz" —1" have tee handles The 007 Series features a modular design concept which facilitates complete maintenance and assembly by retaining the spring load. Specifications Now Available A Double Check Valve Assembly shall be installed at each WattsBox Insulated Enclosures. noted location. The assembly shall consist of two positive For more information,send for literature ES-WB. seating check modules with captured springs and rubber seat discs.The check module seats and seat discs shall be replaceable. Service of all internal components shall be through NOTICE a single bronze or stainless steel access cover secured with Inquire with governing authorities for local installation requirements stainless steel bolts.The assembly shall also include two resil- ient seated isolation valves;four top mounted, resilient seated NOTICE test cocks.The assembly shall meet the requirements of ASSE Std. 1015 and AWWA Std. C510. Approved by the Foundation The information contained herein is not intended to replace the full for Cross-Connection Control and Hydraulic Research at the product installation and safety information available or the experience University of Southern California. Assembly shall be a Watts of a trained product installer.You are required to thoroughly read Series 007. all installation instructions and product safety information before beginning the installation of this product. RECEIVED Watts product specifications in U.S.customary units and metric are approximate and are provided for reference only.For precise measurements, 0 please contact Watts Technical Service.Watts reserves the right to change or modify product design,construction,specifications,or materials with- out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold. AS EN BUILDING DEPARTMENT Pressure — Temperature Suffix: 1"-2" S- bronze strainer Temperature Range: 33°F- 180°F(0.5°C-82°C). LF -without shutoff valves Maximum Working Pressure: 175psi (12.1 bar). SH - stainless steel ball valve handles HC - 21/2" inlet/outlet fire hydrant fittings(2" valve) Standards Prefix: ASSE Std. 1015, AWWA Std. C510 U - Union connections IAPMO PS31, CSA B64.5 �`pSf/F�eO Approvals , sp® " , U. t ASSE, AWWA, IAPMO, CSA, UPC A Approved by the Foundation for Cross-Connection Control and Hydraulic Research at the University of Southern California. • Models LF and S are not listed. • UL Classified(LF models only)3/4"-2" (except 007M3LF) • Horizontal and vertical "flow up" approval on all sizes Dimensions-Weights Models Sizes: 'h"-2" As is •Bs }— • - - �• o —4 1. ■ ® f .• — I, 1--=■1■ 4rI — D s '♦ 1 *Subscript'S'=strainer model MODEL SIZE DIMENSIONS WEIGHT A B C D F G R T in. In. mm in. mm In. mm In. mm In. mm in. mm in. mm in. mm lbs. kgs t♦0070T 'h 10 254 4% 117 27A6 62 — — 5 127 3% 85 25/16 59 21/6 52 4,5 2 TA 007M3QT 3/4 11'% 282 4 102 3'% 79 — — 63/16 157 37A6 87 2%e 54 1316 33 5 2.3 t1007M1QT 1 13'/4 337 51/2 130 4 102 — — 71/2 191 33/6 85 11V6 43 11t/6 43 12 5.4 t♦ 007M20T 1;4 1636 416 5 127 35/6 84 — — 912 241 5 127 3 76 2 50 15 6.8 tA 007M2QT 11/2 163/4 425 47/6 124 3'h 89 — — 93/4 248 513/46 148 316 79 21n6 68 15.9 7.2 t♦ 007M101 2 191/2 495 61% 159 4 102 — — 13%3 340 6'43 156 36 87 2'1A6 68 25.7 11.7 • 00701-S ',h 13 330 6 152 27A6 62 3 76 5 127 3% 85 2Y16 59 2%6 52 5.5 2.5 • 007M301-S 3 141/2 368 616 156 31/2 79 3 76 63/6 157 3/16 87 21/2 54 33 6.7 3.1 • 007M1QT-S 1 171S/e 157 73/4 197 4 102 3% 83 7'% 191 3% 85 1"/i6 43 1"%6 43 RECEIVED • 007M2QT-S 1, 21'h 546 T/i6 179 33/16 84 3'h 83 91/2 241 5 127 3 76 2 50 •007M201-S 11/2 213/4 552 71/16 179 31/2 89 33/4 95 93/4 248 513/16 148 3%s 79 21/6 68 19.6 8.9 • 007M1 QT-S 2 2534 654 83/4 222 4 102 4 102 13% 340 61/2 156 37/16 87 2'/G 68 33.51 d5.22 2/2 0 2 0 Suffix HC - Fire Hydrant Fittings dimension "A" =231/2" (594mm) ASPEN BUILDING DEPARTMENT Dimensions-Weights 1" 0007M1QT Union Tailpiece 1 - ---- Union Tailpiece Union Nut ------- _— Union Nut fit_L w f�oJ [i]ff� ® e I U n --C,. •—+ /1/1/ LIP'j A Sizes: 1" -2" MODEL SIZE DIMENSIONS A in in mm 00070T 1/2 12";,, 326 0007M2QT 'A 1313/16 350 0007M2QT 1 16% 422 0007M2QT 11/+ 20.3/1 527 0007M2QT 1'h 211/2 546 0007M1QT 2 241/2 622 RECEIVED 10/22/2020 ASPEN BUILDING DEPARTMENT Capacity As complied from documented Foundation for Cross-Connection Control and Hydraulic Research at the University of Southern California lab tests. *Typical maximum system flow rate(7.5 feet/sec.,2.3 meters/sec.) "UL rated flow 1/4"(15mm) 11/"(40mm) bars psi * bars psi * n .8 12 , 0..8 12 2 .7 10 - G .7 10 0 .5 8 5 0 .4 6 .4 6 ' H .3 4 y .3 4 ��■� ' 4 .1 2 1 .1 2 a 0 0 _ a 0 0 0 2 4 6 8 10 12 gpm ,. 10 20 30 40 50 60 70 80 90 100 110 120 gpm 0 7.6 15 2 22 8 30 4 38 45.6 Ipm 0 38 76 114 152 190 228 66 304 342 380 418 456 Ipm 5 7.5 10 fps 5 7.5 10 15 fps 15 2.5 3.0 mos 1.5 2.5 3.0 4.5 mps Flow Flow bars psi 3/4"(20mm) 2"(50mm) 15 22 * bars psi * .8 12 -- 12 18 ..7 10 0 f 96 14 _ d .4 6 �� G 7 .3 4 �� 69 10 _ ,_ N `.1 2 w f d 0 0 d 41 6 0 25 50 75 100 125 150 175 200 gpm n 95 190 285 380 475 570 665 760 Ipm 14 2 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps 5 10 15 20 25 30 35 40 45 50 gpm 0 19 38 57 76 95 114 133 152 171 190 Ipm How 75 15 Ips 2 3 4.6 mps Flow 1"(25mm) bars psi G 1.1 16 r c .8 12 C .7 10 g2 .5 8 co .4 6 .3 4 , d .1 2 o 5 10 15 20 25 30 35 40 45 50 55 60 gpm .1 19 38 57 76 95 114 133 152 171 190 209 228 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps Flow 11/4"(32mm) bars psi t 1 14 o .8 12 G .7 10 ao .5 8 y .4 6 .3 4 __-. a .1 2 • . 0 0 0 10 20 30 40 50 60 70 80 90 100 110 120 gpm 1 38 76 114 152 190 228 266 304 342 380 418 456 Ipm 5 7 5 10 15 fps 1.5 23 3.0 4.6 mps Flow % 'WATTS® RECEIVED USA: T:(978)689-6066•F:(978)975-810:4 /1 n O G n O Canada: T:(905)332-4090•F:(905)332- 6 at s a Latin America: T:(52)81-1001-8600•Watts:corn ES ES 007 1808 MEN N aL�NE DEPARTMENT VSR-S P POTTER Vane Type Waterflow Alarm The Symbol of Protection Switch With Retard Features • Assembled in USA _ - • 0-90 second field replaceable time delay retard • Easy to read retard time delay adjustment knob • Fits 1"to 2"CPVC,copper,brass,or iron pipe • Comes with all necessary paddles • Two SPDT(form C)contacts • Weatherproof �-- • Easy to read wire terminal designations • 5 year warranty }_ A CAUTION Wateritow switches that are monitoring wet pipe sprinkler systems shall not be used as the sole initiating device to discharge AFFF, C E sxrtunts deluge,or chemical suppression systems. Watertiow switches used for this application may result in unintended discharges caused by COUS surges,trapped air,or short retard times. - LISTED Important:This document contains important information on the installation and operation of the VSR-S waterflow switches.Please read all instructions carefully before beginning installation. A copy of this document is required by NFPA 72 to be maintained on site. Description Technical Specifications The Model VSR-S is a vane type waterflow switch for use on wet Service Pressure 300 PSI(20,68 BAR)-UL sprinkler systems that use 1"(25mm),11/4'(32mm), 1'h"(38mm)or 2" 1 o GPM(38 LPM) (50mm)pipe size.The unit may also be used as a sectional waterflow To ensure minimum flow of 10 gpm,a minimum pressure is detector on large systems. FAlalow Required for required at all sprinklers with a k-factor of 3 or less. The unit contains two single pole double throw snap action switches K-3:10 PSI and an adjustable, instantly recycling pneumatic retard.The switches K-2.8: 12 PSI are actuated when a flow of 10 gallons per minute(38 LPM)or more Maximum Surge 18 FPS(5,5 m/s) occurs downstream of the device.The flow condition must exist for a Enclosure Die-cast,red powdercoat finish period of time necessary to overcome the selected retard period. Two sets of SPDT(Form C) Contact Ratings 10.0 Amps at 125/250VAC Enclosure 2.0 Amps at 30VDC Resistive 10 mAmps min.at 24VDC The VSR-S switches and retard device are enclosed in a general Two 1/2"conduit connections provided.individual switch purpose,die-cast housing.The cover is held in place with two tamper Conduit Entrances compartments suitable for dissimilar voltages. resistant screws which require a special key for removal. A field Listed plastic,copper,schedule 40 iron pipe and unlisted riser installable cover tamper switch is available as an option which may assemblies approved by Potter. Fits pipe sizes-I",1'/a",I''A"and 2" be used to indicate unauthorized removal of the cover. See bulletin Usage Note:12 paddles are furnished with each unit,one for each pipe number 5401103 for installation instructions of this switch. size of threaded and sweat TEE,one for 1"cPVc,one for I" CPVC(Central),one for I"threaded Nibco CPVC,and one for I''A"threaded(Japan). •NEMA4/1P65 Rated Enclosure suitable for indoor or Environmental outdoor use with factory installed gasket and die-cast housing when • Installation must be performed by qualified personnel Specirt:atiuns used with appmpi late eunduit ruing. and in accordance with all national and local codes and •Temperature Range:40°F-120°F,(4.5°C-49°C)-UL Ordinances. Automatic Sprinkler NFPA-l3 • Shock hazard.Disconnect power source before servicing. One or two family dwelling NFPA-13D Serious injury or death could result. Service use Residential occupancy up to four stories NFPA-l3 R • Risk of explosion.Not for use in hazardous locations.Serious National Fire Alarm Code NFPA-72 injury or death could result. *Specifications subject to change without noticRE / EIVED Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.p,ot ter� a orn gn' l.c 0 5401206-REV Fl • 05'19 �_�/-�PAGEE 1 OF 6 ASPEN BUILDING DEPARTMENT VSR-S P POTTER Vane Type Waterflow Alarm The Symbol of Protection Switch With Retard Installation These devices may be mounted in horizontal or vertical pipe. On horizontal pipe they should be installed on the top side of the pipe where they will be accessible.The units should not be installed within 6"(15cm)of a fitting which changes the direction of the waterflow or within 24"of a valve or drain.Select the proper paddle for the pipe size and type of TEE used see Fig.2 for instructions on changing paddle.The unit has a 1"NPT bushing for threading into a TEE.See Fig. 1 for proper TEE size,type and installation.Use no more than three wraps of teflon tape. Screw the device into the TEE fitting as shown in Fig. 1.Care must be taken to properly orient the device for the direction of waterfiow. The vane must not rub the inside of the TEE or bind in any way.The stem should move freely when operated by hand. The device can also be used in copper or plastic pipe installations with the proper adapters so that the specified TEE fitting may be installed on the pipe run. Note:Do not leave cover off for an extended period of time. Do not trim the paddle.Failure to follow these instructions may prevent the device from operating and will void the warranty.Do not obstruct or otherwise prevent the trip stem of the flow switch from moving when water flows as this could damage the flow switch and prevent an alarm. If an alarm is not desired,a Flowswitch Bypass Switch should be used(refer to Potter data sheet 5401554),or a qualified technician should disable the alarm system. Fig I Retard Adjustment OPTIONAL COVER TAMPER SWITCH The delay can be adjusted by rotating the retard adjustment knob from 0 to the max setting(60-90 seconds). The time delay should be set at the minimum required to prevent false alarms. .,.......A %-404 Old q Paddle Selection :-",--=. 11._,=��I\Il Fig 2 ,, In.... IS!21� I / DIRECTION OF iI`01;; 010 WATER FLOW MOUNT SO ARROW ON, `� ��—�,,�' ' BUSHING POINTS IN '� / DIRECTION OF WATERFLOW \` �►' / , 11 \ � DM G573-JI �� 0_ } , R'p i I"NPTTHREADED FITTING ON ALL SIZES ilit There are 12 paddles furnished with each unit.One for each size of threaded,sweat or plastic TEE as described in Fig.3.These paddles RUN OF THE TEE MAY BE ..) have raised lettering that shows the pipe size and type of TEE that THREADED OR SWEAT PIPE—'O they are to be used with.The proper paddle must be used.The paddle must be properly attached(see drawing)and the screw that holds the paddle must be securely tightened.Do not trim the paddle. DIRECTION OF �a1/4 -.411) WATERFLOW Note: For National Fire Products risers, use paddle marked SWEAT �� mvae no>_;n.� for corresponding size riser. RECEIVED Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.gotOte�2na� o,En20 5401206-REV H • 05/19 1 ^PPAAGLl OFj6 BUILDINGf JDE�PANRTMENT VS R-S PPOTTER Vane Type Waterf low Alarm The Symbol of Protection Switch With Retard TEE Specifications Cover Tamper Switch Wiring Screw the fitting into the TEE fitting as shown in Fig.3. Fig 4 Fig 3 (Shown with cover in place) • • A FLOW 1 11 16" • (43MM) APPROX. © 0 4) 1 ___L C N.O. N.C. H _.4, L__ (WHT) (RED) (BLK) Switch Terminal Connections DEPTH I I Clamping Plate Terminal Fig 5 Ti' DWG#735-33 _J L411 The depth to the inside bottom of the TEE should have the following I 4 S dimensions: 1001 Approximate Depth Requirement fl�c0N�N6 Tee Size Threaded Sweat CPVC 1"x 1"x 1" 2 1/16" 1 3/4" 2 7/16" �rGo1Jc DWG. #1146-16 1 1/4" x 1 1/4" x 1" 2 7/16" 2 7/16" N/A 1 1/2" x 1 1/2"x 1" 2 11/16" 2 1/4" N/A t a ! t k 2"x 2"x 1" 3 3/16" 2 3/4" N/A An uninsulated section of a single conductor should not be looped around the terminal and serve as two separate connections. The wire must be severed,thereby providing supervision of the connection in the event that the wire become dislodged from under the terminal. NOTICEFailure to sever the wire may render the device inoperable risking severe property damage and loss of life. Use only factory TEE's with a 1"NPT bull. Threaded bushings, Do not strip wire beyond 3/8"of length or expose an uninsulated reducing bushings, mechanical TEE's and weld-o-lets are not conductor beyond the edge of the terminal block. When using allowed unless they comply with the dimensions listed in the chart stranded wire,capture all strands under the clamping plate. in Fig. 3 and have been factory approved by Potter.Apply teflon tape to the 1"NPT fitting. Do not use more than three wraps of teflon tape.Do not use any other type of sealant. RECEIVED Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.gottttetssiicna).c�A20 5401206-REV H • 05/19 APAGES OF6 BUILDING DEPARTMENT VSR-S P POTTER Vane Type Waterflow Alarm The Symbol of Protection Switch With Retard Typical Electrical Connections Fig 6 CONNECTOR mik 3ELL NEUTRAL FROM I n fIIIIIIIIIIIIuIIUIIE+ BREAKS NEUTRAL FROM BELL l.\ {1 I BREAKER J o LINE FROM BREAKER 8 EOL(End Of Line Resistor) llit Ell 1E3 WINOTE)oemzn nnecnne a a s�� control panel,use rh=_ounJ's l 0,- esistor value for cn CO sU p=nsion. •"(Ilt (tai 1 --I_ ili %i11 A CAUTION The VSR-S does not require power to operate. Do not connect AC power directly to the temlinals as this will damage the switch. The terminals are for switching power to an indicating appliance such as a bell or strobe. Similar to how a light switch is used to switch power to a light.The terminals can also be used to connect to a fire/security panel. A'ole : 1. The Model VSR-S has two switches, one can be used to operate a central station, proprietary or remote signaling unit,while the other contact is used to operate a local audible or visual annunciator. 2. For supervised circuits,see"Switch Terminal Connections Clamping Plate Terminal"drawing and warning note(Fig.5). Fig 7 Testing Break out thin section of cover when wiring both switches from one The frequency of inspection and testing for the Model VSR-S and its conduit entrance. associated protective monitoring system should be in accordance with applicable NFPA Codes and Standards and/or the authority having jurisdiction(manufacturer recommends quarterly or more frequently). If provided, the inspector's test valve shall always be used for test purposes. If there are no provisions for testing the operation of the te� flow detection device on the system, application of the VSR-S is not '1� — 0111k11111. .��1; 1. recommended or advisable. A minimum flow of 10 GPM(38 LPM)is required to activate this device. 1 „:i 1 NOTICE ,�, „, ._'Ir ��'�6", < ,� ri Please advise the person responsible for testing of the fire ���.,i-,%' � protection system that this system must be tested in accordance .dl�'` with the testing instructions. Do not obstruct or otherwise prevent �*40 � the trip stem of the flow switch from moving when water flows as this could damage the flow switch and prevent an alarm.If an alarm is not desired,a Flowswitch Bypass Switch should be used(refer to Potter data sheet 5401554),or a qualified technician should disable the alarm system. v. RECEIVED _ _ Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-393r, • www.gotte'si na .con 540I2((6-REV It • 05 I A A.P)4)F 6 BUILDING DEPARTMENT VS R-S P POT I Vane Type Waterflow Alarm The Symbol of Protection Switch With Retard Mounting Dimensions Fig 8 3.50" 41., 5 56" -s. GROUND SCREWS (89.0 mm) (141 2 mm) o A 1 f 100" ge 4.1 ,rn"milk (508mm) ' i .dra I Ii _ Ir , i 1.1 1 I 2.34" I (59.4 mm) 9111 4.89" , - -- �1 thri01 `— _•j (52.3 mm) FLOW, Is �» '0, I"-II 1 2 NPT - 0_1 _, ri,-- Maintenance Inspect detectors monthly for leaks. If leaks are found,replace the detector. The VSR-S waterflow switch should provide years of trouble-free service.The retard and switch assembly are easily field replaceable. In the unlikely event that either component does not perform properly,please order replacement retard switch assembly stock number 1029030.There is no maintenance required,only periodic testing and inspection.Vane type watearflow switches have a normal service life of 10-15 years.However,the service life may be significantly reduced by local environmental conditions. Vane-Type Waterflow Switch for Small Pipe Specification UL,CUL Listed,LPCB Approved and CE Marked vane type waterflow switches shall be furnished and installed at each sprinkler system connection to the wet pipe main where indicated on the drawings and plans and as required by applicable local and national codes and standards.The device shall consist of a 1"NPT threaded brass bushing for installation into tees and approved manifolds,gasket and non-corrosive vane and trip stem assembly as well as a field replaceable adjustable time delay/switch mechanism to prevent false alarms from water surges.All wetted parts of the waterflow switch shall be non-corrosive to resist being affected by or contributing to corrosion.The waterflow switch enclosures shall be NEMA 4 rated and the cover shall be held captive by tamper resistant screws.It shall be possible to install an optional cover tamper switch to detect removal of the enclosure.The field replaceable instantly recycling adjustable pneumatic retard shall provide a 0-90 second time delay and visual indication of activation.Expiration of the retard time shall result in the simultaneous operation of two sets of single pole double throw(SPDT)switch contacts rated at 10A, 125VAC and 2A,30VDC.Each switch contact shall have a separate wiring chamber and separate conduit entrance to comply with the NEC requirements for separation of power limited and non power limited conductors without the need for special wire or wire methods.The device shall be listed for pressures up to 300 psi,maximum water surges of 18 fps and alarm activation by a continuous flow of l0gpm.The device shall be Listed for installation on CPVC,brass,copper and iron tees and manifolds from 1"-2"size.The waterflow switch shall be a model VSR-S manufactured by Potter Electric Signal Company LLC. RECEIVED _ _ Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.iooteilyilpl.. U10 5401206-REV H • 0519 ^c GE5QF6 BUILDINf GJDEPANRTMENT VSR-S P POTTER Vane Type Waterflow Alarm The Symbol of Protection Switch With Retard Retard/Switch Assembly Replacement NOTICE The Retard/Switch Assembly is field-replaceable without draining the system or removing the waterflow switch from the i.e 1. Make sure the fire alarm zone or circuit connected to the waterflow switch is bypassed or otherwise taken out of service. 2. Disconnect the power source for local bell(if applicable). 3. Identify and remove all wires from the waterflow switch. 4. Remove the(2)mounting screws holding retard/switch assembly to the base.Do not remove the(2)retard housing screws. 5. Remove the retard assembly by lifting it straight up over the tripstem. 6. Install the new retard assembly.Make sure the locating pins on the retard/switch assembly fit into the locating pin bosses on the base. 7. Re-install the(2)original mounting screws. 8. Reconnect all wires.Perform a flow test and place the system back in service. Fig 9 REMOVE(2)ORIGINAL MOUNTING BREAKOUTTIIIN SECTION OF COVER �-SCREWS HOLDING RETARD SWITCH WHEN WIRING BOTH SWITCHES 12)ORIGINAL MOUNTING \\SSENIBLS TO BASESCREWS FROM ONE CONDUIT ENTR-ANCE, RETARD SWITCH ASSEMBLY , 11 IL, irt ' (2)LOCATING PINS 121 LOCATING PfX� F •'•- BOSSES IN DAS DO NOT REMO\E - ) -_ (2)RETARD HOUSING � Iw Y- -_ r Cr: SCREWS .77g- FLOW N:\SE 1 Removal of Waterflow Switch Ordering Information • To prevent accidental water damage,all control valves should be Model Description Stock Number shut tight and the system completely drained before waterflow detectors are removed or replaced. VSR-S VSR-S WATER FLOW 1144440 INDICATOR • Turn off electrical power to the detector,then disconnect wiring. • Use a wrench on the flats of the bushing.Turn the switch Replaceable Components:Retard/Switch Assembly,stock no. 1029030 counterclockwise to disengage the pipe threads. Paddle Tree,stock no.5559001 • Gently lift with your fingers,roll the vane so it will fit through Paddle Retention Screw,stock no.5490374 the hole while continuing to lift the waterflow detector. Optional Components:Cover Tamper Switch,stock no.0090148 • Lift detector clear of pipe. FSBS-Flowswitch Bypass Switch,stock no. 3001006 DG-B-R Surface Mount Double Gang Box- Red F/FSBS,stock no. 1000484 RECEIVED Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www. otte si na com - - - �2/2020 5401206-REV H • 05,19 ASP F 6 EN BUILDING DEPARTMENT P POTTER. RBVS UNIVERSAL BALL The Symbol of Protection VALVE SWITCH UL and cUL Listed,FM,CSFM Approved Dimensions: (including mounting clamps) AP Large Clamps: 6"L x 5"W x 5.2"H 15,2cmLx 12,7cmWx 13,2cmH Ruffs k Small Clamps: 6"L x 4"W x 5.2"H 15,2cmLx 10,2cmWx 13,2cmH Weight: With Large Clamps: 13.6 oz.(386,9 g.) With Small Clamps: 11.0 oz.(311,2 g.) 114 Enclosure: Non-Corrosive Composite Material Environmental Limitations: • NEMA 4 rated enclosure when proper electrical fittings are used.(1P67) • Temperature range:-40°F to 150°F(-40°C to 65°C) • Not for use in hazardous locations Housing Cover Tamper: Activated by housing cover removal US Patent No.6,945.509 (Stock No. 1000035 only) Contact Ratings: RBVS Stock No. 1000040(w/o Cover Tamper) SPDT Contacts: 10A at 125/250 VAC RBVS-T Stock No. 1000035(w/Cover Tamper) 2A at 30 VDC Optional Cover Tamper Kit Stock No.0090201 SPDT Cover Tamper: 3A at 250 VAC General Installation On Lever Handle(See Fig.2) The Model RBVS is designed to monitor the fully open position of a ball valve 1. Select clamps and clamping bolts based upon pipe Valve size,see Table 1. installed in a sprinkler system.The unit will fit on most ball valves installed on 2. Insert rubber clamp grippers into clamps,see Fig.2. back-flow-preventers and alarm trim lines of dry,alarm,and deluge sprinkler 3. Place one clamp on top of pipe/ball valve near the valve handle and valves.The switch operates if the ball valve handle is moved from the open insert clamping bolts through it. position.However,the switch does not track the position of the handle or ball. 4. Place other clamp over clamping bolts from beneath the installation and When the ball valve handle is in the open position,a spring-loaded switch button thread hex nuts onto the clamping bolts,but do not fully tighten,(be sure will contact the valve handle.When the handle is moved from the open position, hex nuts seat properly in clamp hex recesses).(NOTE:Some installations this switch button extends to the tripped position,and the RBVS contacts change may require one of the mounting bolts to be inserted from the bottom of state,thereby opening or closings circuit.A cover tamper switch is available and the brackets and then trimmed to allow the extension bracket to clear. is activated by the removal of the RBVS housing cover.If an attempt is made See Fig.4) to remove the RBVS by the removal of the mounting brackets,the unit will be 5. Attach extension bracket(if necessary to use for positioning)to top clamp set into the tripped mode by this action. using'/-20 X 3/"Hex bolt and washer,but do not fully tighten. The RBVS can be mounted to the hex portion of the ball valve or back-flow- 6. Attach"L"bracket(RBVS switch enclosure is loosely attached to"L" preventer or to the adjoining pipe via two clamps.The RBVS is shipped with two bracket)to extension bracket using''/e-20X3/."Hex bolt and washer,but sets of mounting clamps to accommodate various pipe and valve sizes,refer to do not fully tighten. Table 1.An"L"shaped and offset bracket for mounting the switch enclosure and 7. Be sure ball valve is in the fully open position. 8. Slide loosely assembled RBVS switch enclosure to a position that permits an extension bracket add to the mounting flexibility of the RBVS.See"Typical the switch button to contact the valve handle approximately I" from its Mounting Diagram"and"Installation and Operation"on following page. inside end.See Fig.1 for approximate location.Cut and remove the plastic Testing coating from the ball valve handle to allow the RBVS switch button to The RBVS and its associated protective monitoring system should be tested contact(and be activated by)the metal of the handle. in accordance with applicable NFPA codes and standards and/or the authority 9. Tighten clamping screws alternately to an eventual 30 in-lbs.(minimum) having jurisdiction(manufacturer recommends quarterly or more frequently). of torque. 10. Maintain position of switch enclosure over valve handle and secure bolt Fig.1 internal Components that holds the extension bracket to the clamping assembly. It may be NORMALLY OPEN necessary to close valve to access this bolt. 11. Position"L"bracket so that it contacts the back edge of the valve handle,and NORMALLY CLOSED r 11111111 , 1 �•� �I secure its bolt.It may be necessary to close valve to access this bolt. 1 COMMON 1111 �..r:=ft 12. With the actuator fully retracted, position RBVS switch enclosure to %,1-43:i 1 contact the valve handle squarely,see Fig. 1. ft�,�' SWITCH BUTTON STRAIN RELIEFZink t LOCATION 13. With RBVS switch enclosure held squarely in contact with valve handle, _ t7 ON HANDLE BLACK - N.O. �� 17 securely tighten the two tamper resistant screws on the backside of the COVER RED - N.C. 4%r�.�.+'--JJf enclosure. TAMPER WHITE - COM - -11 14. Close and open the valve to verify operation.The actuator should easily retract when the valve handle is in the open position. MOUNT SO 15. Fully open the valve. SWITCH BUTTON 16. Remove the cover and wire main switch and tamper switch if applicable. IS APPROX. 1" FROM PLASTIC COATING Carefully route tamper switch wires through strain relief channel in switch HANDLE INSIDE END REMOVED FROM enclosure.Fullyseat the wires into the bottom of the channel.See Fig.1. BALL VALVE HANDLE IN SWITCH BUTTON 17. Replace RBVS switch enclosure cover and securelyr(gp,c �� DWG #1086-1 CONTACT AREA REE Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 866-956-0988/Canada 888-882-1833 • www.potteisigllnal.com PRINTED IN USA MFG.#5401086-REV V 1 U f 44,1 41P,2 0 5,09 ASPEN BUILDING DEPARTMENT P POTTER RBVS UNIVERSAL BALL The Symbol of Protection VALVE SWITCH Fig.2 Typical Mounting Diagram Table l Clamp Sizing LENGTH Pipe Valve/Size Clamp Clamping Bolts 6" SWITCH 1/2"to 3/4"(12,5 to 19mm) Small 10-32 x 2 1/2 ENCLOSURE lilt'7 1"to 2"(25 to 50mm) Large 1/4-20 x 4" 1 1k11 ,i L" BRACKET / ___ 0 HEIGHT Switch Terminal Connections,Clamping Plate Terminal 1 �r == EXT. BRACKET 0� 5.2" w�� `-� (If NECESSARY) `�� A CAUTION m 1 11��\�E \-Loc I i CLAMPS /1 / Aounin of bedseped arosinglee termitor �frke] should not be loo ed around the terminal 11 r �1 10111 L,/ and scree as two scperatc connections.The t CLAMP �� N_,Or wire must he severed, thereby providing GRIPPERS WIDTH supervision of the connection in the event - 4" (SMALL) that the wire becomes dislodged from DWG #1086-2 5" (LARGE) under the terminal. Typical Electrical Connections LOCAL CIRCUIT TRANSFORMER OR BATTERY POWER STYLE 0 (CLASS A) SUPERVISED LOOP STYLE B (CLASS B) SUPERVISED CIRCUIT ��N..C. 'it] COM. COM. TO N.C. SIGNLE CONTROL CAM, END-OF-LINE RESISTOR N,O. oEv cE e` ND R N.O. UNIT N.O. N.C. R "•c• DWG. /loos-a Tamper Switch Connections Fig.3 COVER TAMPER & RBVS CONNECTED COVER TAMPER & RBVS WIRED 6mfCN ENCLOSURE TO THE SAME ZONE ON THE FACP TO SEPERATE ZONES -" COVER CON, N,O.COM. 'WIPER ® OFFSET BRACKET COM N.O. COAL / J 'ACP CWER COLR N.C. -�1/,/,.. I� Ir IJ TAMPER FACP E FACP £EOLR '* /'/� �1I, N.O.0 �' {j. / /l� k Ilik 1 ©f I OwC_Y1086-5 VC- � ��II 4. iInstallation on Tee Handle(See Fig.3) ` f� Sll ® 'i ,�• 1.1�1. Select clamps and clamping bolts based upon pipe/valve size,see Table 1. •\s N.,`V •LBRAME, L— IiI� `Iaii2. Insert rubber clamp grippers into clamps,See Fig.3. , AK ./ „I 3. Place one clamp on top of pipe/ball valve near the valve handle and `;.,, / �1,11��� insert clamping bolts through it. 1 4. Place other clamp over clamping bolts from beneath the installation GRIPPCLAUERS MG 11086-3 and thread hex nuts onto the clamping bolts,but do not fully tighten, (be sure hex nuts seat properly in clamp hex recesses). 5. Loosely attach "L" bracket to the "offset" bracket and "offset" Fig.4 bracket to the RBVS housing. 6. Be sure ball valve is in the fully open position. 7. Slide loosely assembled RBVS switch enclosure to a position that RBVS permits the switch button to contact the valve handle approximately O 1/2"from the end of the handle.Cut and remove the plastic coating II from the ball valve handle to allow the RBVS switch button to contact _ (and be activated by)the metal of the handle. I I 8. Tighten clamping screws alternately and''/4-20 X 3/4"bolt to 30 in-lbs. II Mill (minimum)of torque. SOME INSTALLATIONS MAY &m. WIIM 9. With the valve handle fully open, slide the RBVS housing down CAUSE INTERFERENCE imIt— until the switch o eratesplus 1/8 inch.Tighten the screws holdingBETWEEN MOUNTING BOLT AND t p g OFFSET BRACKET.INSTALL BOLT the RBVS to the"offset"bracket. FROM BOTTOM AND TRIM AS ILK PIPE 10.Remove the RBVS switch enclosure cover. NEEDED TO CORRECT. 11.Close and open the valve to verify operation.The actuator should easily retract up when the valve handle is in the open position. 12.Fully open the valve. 13.Wire main switch and tamper switch(if applicable).Carefully route tamper switch wires through strain relief channel in switch enclosure. DWGa .losrfi � �Eir�ED Fully seat the wires into the bottom of the channel.See Fig. 1. Y 14.Replace RBVS switch enclosure cover and securely tighten cover screw.PRINTED IN USA MFG.#5401086-REV V I(/(?1//`"4ji2 0 2 0 509 ASPEN BUILDING DEPARTMENT Click to see: Stainless Steel Check Valves in our Online Catalog FL_ j4T'IC VALVES i 2� • '....m.... ( I 1 ) cr(11 mir . it ,1 i I - r_ _ _ :.-.., lari:11 ' .: rr_s., --e..,:, : ,,..„..: , (i_ 1i a a. Illh , .... . ,4111 ilt • ', Stainless Steel Check Valves 1 Water and Industrial Applications '`ZO" idki,-,t;4 Certa-LokTM* Model 80S6CL FLZMAncVALVES • Threaded Model 80SS & 80S6VFD Hi h imlrn lohxs Buih m ln>•1... ��1 - Threaded Model 100SS Jl. f fir C,r Low Lead • FLON1ATiC vu`is� ille Threaded Model l 00M S UP Iv 11 iED Ilk krtr; it low lead law @� 1 *Certa-Lok'"is a registered trademark with a Certainteed Corporation. FlomaticaO 2 O High Quality Valves B€ a-1 st BUILDING DEPARTMENT America 's # 1 Unlead E_ Industry Proven Design = New Guide Leg Follower One of the most complete Stainless Steel When well water is pumped it can product line in the industrial valve marketlib cause potential failure to check valves. Industry proven design and millions in operation, Flomatic's new series "H" check valve patented WORT' (Warranted Check Reliability) eliminates start-up problems in water well poppet has evolved from Flomatic's pioneering k-.,,,.II systems due to sand and debris, work in stemless poppet design to eliminate _-lig The 'H.model is now standard problems associated with stem guided valves. 4...-- ° in all 7'check and foot values We believe our valves to be the best on the market today from any standpoint — poppet "H" model is now standard strength, head loss, long life, noiseless, and trouble-free operation. Flomatic Valve Advantages The patented WCR"' poppet is designed to float evenly in the water flow when the valve is open- With the WCRThs poppet, Flomatic valves give you these advantag( It will not flutter, spin, or wobble, this eliminates a • Stemless design eliminates sticking major cause of poppet wear and valve hang-up. • Incorporates patented features to maximize performance ■ Tapered valve seat is self-cleaning FimiltAinkr 1 helms Ietills Stable poppet reduces wear, eliminates noise wive Glide Stemless Design Eliminates Sticking IF Lowest head loss of any comparable valve Valve Seat todius Yahe Seat Self(leaning Vane Seat Itti FLO-FIN preventing pipe end from %W hipet Drop Slope Poppet Reduce hidioe loss blocking off flow (PATENTED) to lielloss larger Flaw areas fora Friction is y, Long wearing, corrosion resistant Poteoted FlO�MIWiwi Rao materials are used throughout— Enviro-Check" No hi $ stainless steel, Buna N rubber, Delrin" 100%Wale(Tested Wu ham end Sea lasted Ensured Dperatios I Can be used with water, oil or gasoline 5leor Warranty Nigher Gray Assume torn Ornashia(off 100% tested under water pressure i. s► Model BOSS Features Stainless Internalsw check w These New ick valves have durable Internals •,,, r 1 II far mare aggressive applications. They feature as i,,ii 1 - ' - i I all 316 stainless steel guide. The stainless ,Ir.'" j internal poppet system b also aeail@bl.oar an U .° i ••••11! t• I c 4 . _ option in off our E n ina-chede vottirply 2 02 0 rd ASPEN BUILDING DEPARTMENT d Valve Manufacturer Flomatic's check valves are made from the finest materials available to provide long life and superior performance. Poppets are of Delrina with Buna-N rubber sealing discs and stainless steel springs. These check valves are suitable for use in water, oil and gasoline, and are warranted for five years. 1110, [111 n ri ..v... .Ire ii 11 SIZE MODEL MODEL MODEL MODEL MODEL MODEL MODEL MODEL MODEL MODEL Female x Female 80S6 80SS 100SS 8OSSA 80SSC 80SSB 80SSXB 80SSHT 80S6CL 8OS6MCL Threaded F x F Hexed Shape F x F I/8"Tap on Inlet 4 Tops-I/8" 1/8"Tap on Inlet, 2-I/4"Taps High Temperature (FRTA-LON°' (ERTA-LOR'" on Inlet,2-1/4" 1/4"on Outlet on Outlet Poppet Male NPT Outlet,1/8"Outlet 1" 403156 4031SS2 4201552 4041552 40615S2 4051552 4031H155 - 1-1/4" 403256 4032552 4202552 4042552 4062552 4052552 7961552 4032HTSS - 1-1/2" 403356 4033552 4043SS2 - - 7963552 40330155 2" 403456 4034552 - 4044S52 - - 4034HTSS 793756(1 793756M(L 2-1/2" - - - - 4035HTSS - 3" 793856 - - - - - 4036HTSS 793856CL 793856M(L 4" 793956 - - - - - - - 793956(L 793956M(L 6" 408956 - - - - 408956(1 408956M(1 8" 4090XSS - - - - - - - 10 4091XSS - - - - - - - Boy • •FL4ATICVALVES -� EINJ,. . ,C -i-,FIE,-F', Er,�., F'r:=1- of-1T , it7:71:1111W ..,, . Heedoos Chat Modal KGSAOCISS IMAdla -chalrt MOM NN a MNc< • 1�1 r r ram. ee,arm • MI r so no r.r r so•a r�rrr.r�s r•.-S S��a =1::::: •:•• ��21 r..r•t•�4 iaI sx•t: ����� �•�� •�[�ta1•�I(•f(•�•�/AI��1� • t•• f�f•01t•f�••a11•11111N 1=1121fit/.__.al••a►•/off♦__. a "a �ae�rf�2if•Uaa�ffa!f•'I•Ifie/f•i•%e//��/.�■ .MuM..uus �1•."I11S11/ti•rrMIlfl.a i Nit�fl�Mititilef'AMNlr.IIar�M/.aalll��r.it■ i MI• ha slau1s)MMc11s1•Is1r aaNIr a111r�sM•u• ' MP •slMall01MMh11t►�IMMIA r./■I.a11/"/�Nosommumilmearannew.inemi_�/1M■ IIIILI MEa•/nimillise�1MIAM•I-i/1•/•aaf,�.af• �f•Mitfst�it�all�aft i,it�it►If•�r,�•f••��a■ a •• woolI�s Ma1)ImwAmmori.U�/11immism■ • u Nalal�M�i1)ICl/N/gal./al/I)Iaalt,>>al■ ■/i■u/!!11/%NIPAU uu11�%•uu • .• : ■■■IIMMIII11�IIAMINI/%111I#1•�0A ■��r���111I��►/i/.�IIIl����1 ■111Ili1111l111/4!%i11PAIII1[/M■IIII a, 111111!:iil�.C%;i11111111.1111111• �, 11:1ll11111AIrall:JI111',�i�11 • • • ••. a s s s ss! I I ! s s s sss !, ! ! ! !!! FLOW IN GALLONS PER MINUTE RCW RAT1NININ tJiEV UP-GRADE OPTION: RECEIVED 4 FLMAT1CvivsStainless on a1 models. I High Quality Valves BuiAtptt... BUILDING DEPARTMENT Other Flomatic Products .z Ia., , iiiii 111 _ /- I . i r' '. ,., Check Valves Model$OOWFD ;all %. I t Control Valves - Pi • . i -. ' - 1 et ` . A. %.......' Ji /11 . II 11, m, . • • r ....... I ilk 104,4,44: •_1 . . .......,_b. fariT. 410, 011* Unleaded Check Valves Wastewater Valves w fir• fot illk ig' i'' 1 :Illalti, ., • I 4. Stainless Steel Valves Ductile Iron Valvss Warranty:LIMITED ONE YEAR WARRANTY:The Flomatic Corporation warrants that its Check Valves in all sizes are free from defects in materials and workmanship.Flomatic will replace any valve covered by this warranty found to be defective within one year from time of sale.This warranty will be void if the product has been modified in any way by the purchaser,or is subject to unreasonable use. Flomatic can accept no responsibility for possible errors in catalogues,brochures and other printed material. Flomatic reserves the right to alter its products without notice.This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies.Flomatic and the Flomatic logotype are trademarks of Flomatic.All rights reserved��(E I\ /E D V Flomatic Corporation Telephone: 1-(800)-833-2040 Direct Telephone: 1-(518)-761-9797 FlomaifNa /2 0 2 0 FL,MATIC'VALVES 15 Pruyn's Island Drive Fax: 1-(800)-314-3155 Direct Fax: 1-(518)-761-9798 HiOr Qualm t4hcseAolAsL� Glens Falls,NY 12801-4421 www.flomatic.com ss the H Fi' UILDIN6tE ARTMENT