HomeMy WebLinkAboutFile Documents.1315 Sage Ct.0082-2021-BRES (13) Residential Design Standards
Administrative Compliance Review Applicant Checklist - Single Family and Duplex
Address: 1315 Sage Court Representative: Zone 4 Architects LLC
Parcel ID:273501303002 Email:colleen@zone4architects.com
Zone District/PD: R-30 Phone:978.853.2110
Instructions:Please fill out the checklist below,marking whether the proposed design complies with the applicable standard as written or is requesting Alternative Compliance(only
permitted for Flexible standards).Also include the sheet#(s)demonstrating the applicable standard.If a standard does not apply,please mark N/A and include in the Notes section why
it does not apply.If Alternative Compliance is requested for a Flexible standard,include in the Notes section how the proposed design meets the intent of the standard(s).Additional
sheets/graphics may be attached.
Disclaimer: This application is only valid for the attached design.If any element of the design subject to Residential Design Standards changes prior to or during building permit review, the
applicant shall be required to apply for a new Administrative Compliance Review.
Standard MI Complies Alternative N/A 1 Sheet#(s)/Notes
Compliance
Refer to Existing Plans and Proposed Plans (A200 + A300). The existing home
B.1.Articulation of Building Mass is to remain with the detached garage being rebuilt and connected to the home.
(Non-flexible)
B.2.Building Orientationki Existing home.
(Flexible)
B.3.Build-to Requirement i Existing home on site with set backs.
(Flexible)
[1
There is an existing one-story entry element that is to remain.
B.4.One Story Element
(Flexible)
[
The garage is accessed via the driveway from a private street. The existing home
C.1.Garage Access has their garage accessed this way and the proposal is to rebuild the garage in a
(Non-flexible)
very similar location.
C.2.Garage Placement
(Non-flexible)
g The garage width is far less than the width of the living area on thRlE EIVED
C.3.Gara e Dimensions
(Flexible)
06/04/2021
Page 1 of 2 ASPEN
BUILDING DEPARTMENT
Residential Design Standardslir
Administrative Compliance Review Applicant Checklist- Single Family and Duplex
Disclaimer:This application is only valid for the attached design.If any element of the design subject to Residential Design Standards changes prior to or during building permit review, the
applicant shall be required to apply for a new Administrative Compliance Review.
--� Sheep#(s)/Notes
C.4.Garage Door Design 1 The new garage doors will be divided to give the appearance of two separate
(Flexible) garage doors. See Proposed Garage Elevation sheet in A400 series
D.1.Entry Connection
1 T
(Non-flexible)
D.2.Door Height 1 The existing front door is to be replaced in the same size which is 8'0".
(Flexible)
D.3.Entry Porch 1 The existing entry porch meets the one-story height requirement.
(Flexible)
E.1.Principle Window 1 There is an existing grouping of windows on the principle facade that meet this
(Flexible) requirement. See sheet A400 series.
E.2.Window Placement
1 T
(Flexible)
E.3.Nonorthogonal Window Limit The non-orthogonal windows are on the existing home and are not street
(Flexible) facing.
E.4.Lightwell/Stairwell Location The egress well is on a non-street facing facade and not visible from any
(Flexible) streets.
E.5.Materials ✓
Refer to Existing and Proposed Elevations (A400 series) for the barnwood siding.
and the standing seam metal roof. Existing barnwood is the material th 9 IVEJj)
(Flexible) and the new addition will have siding to match. a
06/04/2021
Page 2 of 2 ASPEN
BUILDING DEPARTMENT